Buscar en el registro

EE was trying to clean the frozen ice and coal out of the chute for loading the pneumatic trucks at Wildcat. EE was standing below the chute mouth and had a long bar by which he was shoving up into the output mouth of the chute. While prying and probing, a piece of frozen material broke loose from the chute and fell, striking EE on the right hand upon the forefinger.

Employee was preparing to hook a shield for extraction from the face. He threw a chain/sling across the shield to be hooked up. When he stood up he wrenched/strained his back and was reporting to be in pain.

While using a hammer to remove a bearing on an underground truck, a small piece of metal was splintered off and it penetrated into the individual's right middle finger tip. Metal was removed by doctor.

While cutting the tape off of the leads in a cable splice, the individual slipped with the razor knife and cut his left hand palm. The laceration required 8 stitches to close.

While cutting open rock dust bags with a razor knife, individual was cutting towards himself and the knife came through the bag and it struck him in the right lower thigh, causing a laceration that required 2 stitches to close.

While cutting a flapper off the belt, the razor knife cut through the belt and then cut the individuals other hand. The laceration required 5 stitches to close.

The employee was setting a timber using a jack pot. The timber broke and hit him, and the jack pot hit him in the head.

The employee was cutting a "flapper" off the belt. The flapper was approx. 60' long and 14" wide. He needed to cut it into shorter lengths so he could drag it out of the structure. He was cutting towards himself and when the knife slipped it cut his thigh. He required 3 stitches.

The employee was removing an axle from a Pod Duster with a 48" pipe wrench. The pipe wrench slipped off of the axle and the employee's thumb was smashed between the pipe wrench and the frame of the duster.

EE REACHED UP TO CUT OFF A PIECE OF WIRE FROM THE ROOF AND FELT A SHARP PAIN IN HIS BACK (ROCK LOCKING FOR MICON).

THE INJURED EE WAS OPENING A BUNDLE OF RESIN GLUE CARTRIDGES WHICH WAS LOCATED ON TOP OF THE ROOF BOLTING MACHINE. HE WAS USING A UTLITY KNIFE. AS HE WAS CUTTING THE OUTER PLASTIC WRAPPER, THE KNIFE SLIPPED AND CUT HIS LEFT THUMB. SUTURES WERE REQUIRED.

EE WAS LIFTING HYDRAULIC JACK & HIS FINGER WAS PINCHED BETWEEN THE JACK & THE FRAME OF THE HEADGATE/STAGELOADER CAUSING A CUT TO THE RIGHT INDEX FINGER

INJURED EE WAS ROOFBOLTING AND WAS IN THE PROCESS OF BENDING A WIRE-MESH MAT WHICH HAD BEEN BOLTED TO THE ROOF. AS HE WAS BENDING THE MAT WITH A PAIR OF PLIERS, THE PLIERS SLIPPED OFF THE MAT AND STRUCK HIM IN THE MOUTH. THE EE FINISHED THESHIFT, BUT WENT TO THE DENTIST THE NEXT DAY. THE DENTIST REPAIR A BROKEN TOOTH AND THE EE MISSED THE NEXT REGULARLY SCHEDULED SHIFT.

EE WAS SITTING ON THE GROUND USING A SHOVEL TO REACH UNDER THE BELT.. HE WAS KICKING ON THE SHOVEL TO LOOSEN THE COAL WHEN HIS KNEE POPPED.

THEY WERE PREFORMING REPAIR WORK ON THE ROLLER PAN LINE UNDER THE 48" PRIMARY BELT THAT RUNS FROM UNDERNEATH THE ROTARY BREAKER AND OUT TO THE TRANSFER POINT. THEY HAD JUST FINISHED CUTTING O UT A SECTION OF OLD PAN LINE THAT HAD RUSTED THROUGH UNDER THE 48" RAW BELT. THEY HAD LIFTED THEINTO PLACE & EMPLOYEE HAD ATTACHED HIS END TO THE FRAME. THE HOLDING CLIP BROKE & MASHED FINGER.

EMPLOYEE WAS PREPARING FOR THE 1450 DRAGLINE TO WALK BACK. HE WAS USING A POCKET KNIFE TO CUT A PIECE OF 1" HEMP ROPE TO MAKE A SLING THAT IS USED TO PULL THE TRAIL CABLE AS THE DRAGLINE WALKS BACK. HIS KNIFE SLIPPED CAUSING HIM TO CUT HIS LEFT FOREARM. HE RECEIVED A 2" LACERATION TO HISLEFT FOREARM MIDWAY BETWEEN HIS ELBOW AND WRIST.

TRYING TO DRIVE THE CONNECTING PINOUT OF A BELT HEADER DRIVE CHAIN WHEN A PIECE OF THE PIN BROKE OFF STRIKING HIM IN THE HAND. THE PIECE OF METAL HAD TO BE REMOVED & R SUTURES WERE NEEDED.

USING A WIRE ROPE TO PULL BELT STUCTURE THRU A MUDDY AREA. THE ROPE BROKE CAUSING IT TO SPRING BACKWARDS HITTING HIM IN THE CHEST. THIS RESULTED IN TWO PUNCTURE WOUNDS TO THE CHEST.

USING A BOW SAW TO CUT A ROUND TIMBER WHEN THE SAW SLIPPED OUT THE TIMBER & CAME IN CONTACT WITH HIS LEFT INDEX FINGER CAUSING A LACERATION THAT REQUIRED 6 SUTURES.

EE WAS HELPING INSTALL A PIN IN A CAT PAD. HE WAS HOLDING A HAMMER AGAINST THE PIN. AS ANOTHER EE HIT AGAINST EE'S HAMMER WITH ANTOHER HAMMER A PIECE OF METAL BROKE OFF OF EE'S HAMMERS STRIKIN G HIM IN THE RIGHT KNEE.

INJURED EE WAS USING A THREAD TAP TO CLEAN THE THREADS OF A BOLT HOLE. THE TAP BROKE & CUT HIS RIGHT INDEX FINGER. SUTURES WERE REQUIRED.

INJURED EE WAS CHIPPING SLAG OFF OF A WELD, HE HAD JUST COMPLETED. A SMALL PIECE OF METAL HIT HIS EYE. THE EMERGENCY ROOM DOCTOR REMOVED THE PIECE OF METAL & PRESCRIBED MEDICINE FOR THIS INJUR Y.

EMP WAS HELPING THE DRAGLINE CREW CHANGE A DUMP ROPE ON THE 1450W BUCYRUS ERIE DRAGLINE. WAS USING A 6' LONG PRY BAR TO SEPARATE THE DUMP SOCKETON THE ARCH OF THE BUCKET. AS THE SOCKET CAME AP ART THE BAR SLIPPED, STRIKING HIM IN THE LEFT CHEEK JUST BELOW LEFT EYE. RECEIVED TWO SUTURES ONTHE LACERATION.

EE WAS USING A HAMMER TO TIGHTEN DOWN A CONCRETE BLOCK BRATTICE WHEN HE HIT HIS FINGER WITH THE HAMMER MASHING IT BETWEEN THE CONCRETE BLOCK AND THE HAMMER.

USING A HANDY MAN JACK TO RAISE AND LEVEL AND BELTLINE WHEN HIS HAND SLIPPED OFF OF THE JACK HANDLE CAUSING THE HANDLE TO RAISE UP AND STRIKE HIM IN THE FOREHEAD OVER THE LEFT EYE.

EE WAS PERFORMING REPAIR WORK ONA CONE TANK INTEH WET PLANT. HE WA ATTEMPTING TO TRIM A SMALL PEG OUT OF A PIECE OF WOOD WITH HIS POCKET KNIFE TO PLUG A SMALL HOLE IN THE TANK. AS HE WAS PUL LING ON THE KNIFE, I SLIPPED OFF OF THE WOOD AND CUT HIS LEFT HAND IN THE PALM AREA. THE LACERATION RESULTED IN FIVE SUTURES.

EE WAS USING A COME A LONG WHEN THE HOOK SLIPPED CAUSING THE COME A LONG TO HIT HIM IN THE MOUTH.

USING HAMMER AND PLIERS TO BEND OUT STAMPED CONCRETE ANCHORS. INJURY- CRACKED BONE IN RIGHT HAND/ SMALL FINGER BELOW KNUCKLE.

INJURED WAS PERFORMING REPAIR WORK ON A 1000 WATT MERCURY HALIDE LIGHT FIXTURE ON THE B.E. 2550 DRAGLINE. HE HAD THE LIGHT FIXTURE CLAMPED IN A VISE ON THE WORK BENCH. HE WAS IN THE PROCESS OF TRYING TO DISMANTE THE FIXTURE WHEN IT SLIPPED OUT OF THE VISE AND STRUCK HIM IN THE FOREHEAD.

EE WAS CLEANING UP IN THE RAW COAL TUNNEL. HE WAS USING A 4FT PRY BAR TO MOVE A LARGE PIECE OF RROCK OUT OF THE WALKWAY AS HE PRYED HE FELT A SHARP PAIN IN HIS LOWER BACK.

EMPLOYEE WAS DRILLING A ROOF BOLT HOLE WITH A DRILL STEEL AND AN EXTENSION WRENCH, THE SOCKET PORTION OF THE WRENCH CAME OUT OF THE CHICK HOLDER STRIKING HIS HARD HAT. THE IMPACT OF THE SOCKE T FORCED HIS HARD HAT DOWN CUTTING HIS FOREHEAD.

USING HAND TOOL EMPLOYEE USING PRY BAR TO DISLODGE METERIL ANCHOR POINT SLIPPED CAUSING OPPOSITE END OF BAR TO STRIKE EMPLOYEE ON LEFT EAR

EMPLOYEE HAD SOME PLASTIC WATER PIPE CHAINED TO THE TOP OF A SCOOP WITH A CHAIN BINDER, WHEN HE WENT TO RELEASE THE BINDER, THE HANDLE SLIPPED OUT OF HIS HAND AND HIT HIM IN THE MOUTH.

EE WAS CUTTING A METAL BAND ON BUNDLE OF 2FT ROOF BOLTS. WHEN THE BAND CAME LOOSE, IT FLIPPED AND HIT THE EE ON THE BACK OF HIS HAND.

TWO EMPLOYEE'S WERE INSTALLING A SHEARHEAD JACK ON THE CONTINUOUS MINING MACHINE. ONE EMPLOYEE WAS USING A PRY BAR TO ALIGN JACK INTO POSITION THE SECOND EMPLOYEE WAS PUSHING ON THE JACK (APP LING PRESSURE) WHEN THE PRYBAR SLIPPED THE END OF THE SHEARHEAD JACK MOVED STRICKING THE SECOND EMPLOYEE'S HAND CAUSING IT TO BE MASHED BETWEEN THE JACK AND THE MINING MACHINE.

I.NAME WORKING ON PROPEL BRAKE ON DRAGLINE WITH A SLEDGE HAMMER.DRIVING BRAKE ASSEMBLY APART.SO-METIME DURING SHIFT REINJURED LOWER BACK.HURT LOWER BACK MOVING A TRAIL CABLE ON 2-26 BUT DIDN T RECEIVE MEDICAL ATTENTION.

EMPLOYEE WAS HOLDING PRESSURE ON PAD WITH PRY BAR.WHILE ANOTHER EMPLOYEE WAS REMOVING PAD BOLT.WHEN THE BOLT CAME OUT OF THE TRACK ROLLED OFF IDLERS THROWING EMPLOYEE OFF DOZER.

EMPLOYEE WAS PREPARING BELT TO MAKE A SPLICE IN BELTLINE WHILE TRIMMING EXCESS RUBBER OFF OF THE BELT THE KNIFE CUT THROUGH THE MATERIAL & CUT RT HAND (BASE OF THUMB) WITH WHICH HE HAD BEEN HO LDING PRESSURE ON THE BELT

EMPLOYEE WAS REPAIRING A SHUTTLE CAR CABLE SPLICE. HE PULLED THE OLD SPLICE FROM THE CABLE AND CUT HIMSELF ON HIS KNIFE.

EMPLOYEE WAS PUTTING A BREAKER IN AT THE POWER CENTER WHEN HE GOT HIMSELF IN A BIND A HURT HIS BACK.

EMPLOYEE WAS TIGHTENING CAT TRACKS ON A 14CM CONTINUOUS MINER.WHILE THE CATS WERE BEING LIFTED OFF THE FLOOR BY THE BOOM AND STAB JACK,EMPLOYEE RELIEVED THE PRESSURE FROM THE TAKE-UP IDLER WIT H SOCKET AND RATCHET SET.AFTER THE PRESSURE WAS RELEIVED,EMPLOYEE TOLD ANOTHER EMPLOYEE TO LOWER THE MINER.AS THE MINER WAS LOWERED,EMPLOYEES LEFT FINGER WAS PINCHED BETWEEN WRENCH AND MINER.

EMPLOYEE WAS CHANGING A TRAM MOTOR ON A MINER WHEN THE WRENCH SLIPPED AND HE HIT HIS HAND. EMPLOYEE SUFFERED A HAIRLINE FRACTURE ON HIS RIGN FINGER OF HIS RIGHT HAND.

I NAME WAS REMOVING A ROLL BACK CYLINDER FROM THE #5-580 HE HAD HIS SERVICE TRUCKS BOOM HOOKED TO THE CYLINDERR I NAME WAS DRIVING OUT THE PIN WITH A 20LB SLEDGE HAMMER WHEN THE PIN SLIPPED FR EE THE CABLE ON THE BOOM BROKE CAUSING THE CYLINDER TO FALL KNOCKING I NAME BACKWARDS AS HE WAS FALLING HE CAUGHT HIMSELF WITH THE SLEDGE HAMMER HURTING HIS LOWER BACK

WAS HAMMERING ON TRACK IDLER AND A PIECE OF METAL CAME OFF HITTING HIM IN RIGHT KNEE.

EMPLOYEE WAS USING A PRY BAR TO REMOVE A WHEEL SPINDLE FROM A BACK DUMP. HIS HAND SLIPPED UP AND OVER THE END OF THE BAR CAUSING A CUT ON THE PALM OF THE RIGHT HAND BETWEEN THE THUMB AND FOREF INGER. TREATMENT: 3 SUTURES AND TETANUS INJECTION.

EMPLOYEE WAS ASSISTING THE OTHER SHUTTLE CAR OPERATOR IN ADJUSTING THE CONVEYOR BELT AT THE TSAILPIECE.HE WAS USING A PRY BAR TO RAISE THE LID OF THE TAIL PIECE,WHEN HE TRIED TO PUSH THE BAR A BOVE HIS HEAD HE FELT A SHARP PAIN IN THE MIDDLE OF HIS BACK.EMPLOYEE WAS TAKEN TO HOSPITAL ER ANDRELEASED AFTER EXAM.HE RETURNED TO WORK ON 02-19-91 BUT HAS MISSED WORK SINCE 02-21-91.

EMPL WAS CHANGING BRAKE DISC ON SHUTTLE CAR. HE WAS PRYING DISC WITH SCALING BAR WHEN IT SLIPPED HITTING HIMSELF IN RIGHT ELBOW. EMPL CONTINUED TO WORK NEXT FEW HOURS & THEN ASKED TO BE TAKEN TO HOSPITAL FOR TREATMENT.

EMPL WAS PRYING TRANSMISSION OUT OF DOZER & BAR SLIPPED INJ ARM & SHOULDER.

ATTEMPTING BELT SPLICE PULLING BELT WITH COME ALONG AND PORK CHOP PORK CHOP SLIPPED OFF BELT STRIKING HIM IN EYE

EMPLOYEE WAS DISMANTLING ENGINE PARTS (HEAD BOLTS). WHEN PRESSURE WAS APPLIED TO HAND TOOL, THE BOLT BROKE CAUSING THE HAND TO STRIKE THE ENGINE HEAD.