Buscar en el registro

Employee was in the process of removing the cutting edge bolts from the bottom of a John Deere 324G skid steer, with leather Tillman gloves using a Milwaukee half inch impact. While removing the second bolt it spun, and caused a burr on the bolt to cut EE's ring and middle fingers on the bottom of EE's right hand. Employee was taken to clinic and received 14 stitches.

Employee was tracking the trommel plant to the pit. Something popped and struck the employee on the middle finger of the left hand.

Employee was cutting a piece of 2" angle iron with a Milwaukee grinder. A piece of the grinder broke off and kicked back into the employee's right leg cutting EE's knee. Grinder did have the guard on at the time of the incident. Employee went to clinic and received four stitches.

Technician was laying under machine to break back bead with a hydraulic ram. While utilizing ram, back bead broke then hydraulic ram fell and struck technician in the face resulting in 4 stitches to the upper lip.

Employee was welding up two guards when EE took welding helmet off because it was flickering on and off. Employee decided to finish the weld without helmet on. On 2/6/25 EE reported to Supervisor that EE's eyes were bothering EE and EE wanted to go to the doctor. Employee went to clinic and was diagnosed with welding burn and issued prescription eye drops.

Employee was using a wire wheel on a rusted piece of metal when employee felt something go into eye, underneath safety glasses. Employee flushed eye but still felt something in there. Went to clinic, where they removed a piece of metal and issued prescription antibiotics.

Employee was grinding on a piece of metal when a piece of metal went under EE's safety glasses and into EE's left eye. The employee went to the doctor where they removed the piece of metal on the surface of EE's eye and issued prescription eye drops.

Employee was adjusting impact crusher and one employee was raising and lowering cylinder and other employee was turning nut. When the one employee turned the nut the other employee pushed lever to lower cylinder, the other employee stuck hand back in quickly to re adjust and smashed two finger tips

Exact date of injury is unknown. Employee was using a welder when sparks penetrated through the long sleeve of EE's right arm. Employee cleaned the arm but pain and swelling increased. Employee went to doctor on 06/27/2020 and was diagnosed with cellulitis.

The employee was using a 8" hand held grinder to square up the excavator bucket pin boss face. When grinding employee got a piece of steel in left eye. Employee received medical treatment to have it removed.

Using a 1/2" drill to tighten a splice. The drill spun my right hand around when the nut bottomed out.

Holding a piece of metal while cutting it.

EE WAS DIGGING ROCK OUT FROM UNDER SCREEN PLANT. A ROCK FELL FROM THE PLANT AND HIT THE LOADER BUCKET AND BOUNCED AND HIT EE ON HIS RIGHT KNEE. CAUSED A BRUISE AND SPRAIN ON EE'S RIGHT KNEE.

CHECKING FOR CRACKS IN BARGA USING WIRE BRUSH AND TORCH GOT BRUSH CAUGHT IN GLOVES CUFF, TORCH FELL OVER ON GLOVE BURNING HAND.

CABLE FROM CRANE CAME UNHOOKED FROM FAR SIDE WHEN HOIST PRESSURE WAS APPLIED CAUSING BELT TO TOPPLE TO ONE SIDE, FALLING ON LEG.

EE WAS ASSISTING IN PUTTING A 120' CONVEYOR BELT ON WHILE THE GRADER WAS PULLING THE CABLE ATTACHED TO THE BELT. THE CABLE KINKED AND EE HAD HIS FOOT IN THE AIR & THE KINK CAUGHT HIS FOOT & RA ISED HIM IN THE AIR & WHEN THE GRADER BACKED OFFHE FELL ON HIS RIGHT SHOULDER & NECK.

WAS ENGAGING DRILL TO STEEL STOCK. WHEN THEY MEET THE DRILL BROKE CAUSING STOCK TO SHIFT AND IT MOVED AROUND AND CAUGHT HIS RIGHT RING FINGER WHEN IT SPUN.

WAS WELDING ON DREDGE. HAD WELDING HELMET AND GLASSES ON. HOT SLAG GOT INTO LEFT EYE.

EMPL CUTTING RUSTY PIPE FROM THE BOTTOM OF A HOPPER WITH WELDER WHEN A PIECE OF HOT RUST POPPED BEHIND SAFETY GLASSES STICKING TO LEFT EYE.