Buscar en el registro

EE was helping install safety chains on the presip catwalk. he was holding a latch for EE White to weld. The welding rod accidentally while showing another ee were he should hold the part, and touched the part. a spark came off and went over EE safety glasses into his left eye lid.

Employee was removing masking tape from an air line in the bag house, when the air system was turned on. This employee's head was right next to an air vent when the system came on next to his left ear.

The subject was washing truck scales with high powered pressure washer, when he inadvertently struck the palm of his left hand, subject's hand is swollen and aching with a small laceration in the center.

Employee was sitting in a chair at the valve-bagger station. You push foot pedal then a bag fills up, slide the bag off, slide the next one on, then press the foot pedal down. He said he pushed the foot pedal down then he felt a pain go from the bottom of his left leg up to his lower back.

Employee saw plastic caught in two of the small belts by the knife on machine #137 and tried to remove it while belts were still running fracture of left index finger.

EMPLOYEE WAS WELDING PIPE IN PLACE ON ELEVATOR & A PIECE OF SLAG DROPPED IN RT.BOOT & BURNED RT. ANKLE.

WELDING BUILDING MATERIAL PIPES & GOT WELDER BURN TO RIGHT EYE.

Grinding and welding on feed hood when foreign object got in left eye.

EE WAS INSPECTING EAST MILL & PIN SHEARED & ARM KICKED BACK & STRUCK RIGHT HAND & FOREARM.

AIR HOSE CAME OFF CAUSING EMPLOYEE TO DROP JACKHAMMER, CAUGHT WITH RIGHT HAND AND BROKE RIGHT THUMB.

EMPLOYEE WAS USING 90 LB. JACKHAMMER TO BUST OUT REFRACTOR IN KILN.

CUTTING ON HOPPER CONE WHEN IT GAVE WAY AND WHILE PREVENTING HIMSELF FROM FALLING FELT SOME PAININ ABDOMEN AREA.

WHILE CHECKING POWER SUPPLY, BELT CAME ON AND TWISTED RIGHT ARM IN BELT DRIVE AND REDUCER SHEAVE.

EMPLOYEE WAS CUTTING BOARD WITH A TORCH OVERHEADAND A FOREING OBJECT BOUNCHED OFF GLASSES AND ENTERED RIGHT EYE.

EE WAS CUTTING WITH TORCH HELPING WELDER. THE WELDER FLASHED CAUSING A BURN TO BOTH EYES.

EE WAS USING A CUTTING TORCH TO CLEAN SLAG OFF OF CASTINGS--A PIECE OF SLAG POPPED UP AND HIT EE IN THE RIGHT EYE. EE HAS EXTENSIVE ABRASION TO RIGHT CORNEA.

EMPLOYEE WAS SETTING MILLS- MILLS HAD BEEN SHUT OFF & ELECTRICAL DISCONNECTS HAD BEEN PULLED. OPERATOR [WITH GLOVE] ON RIGHT HAND & HOLDING GAUGE 1/2" FROM END OF GAUGE. HE STUCK GAUGE INTO MI LL. MILL ROLLS HAD NOT COME TO A COMPLETE STOP & EMPLOYEE RIGHT FOREFINGER WAS CAUGHT IN MILL ROLLS.

WHILE USING THE COP SAW, EMPLOYEE GOT A SPARK IN HIS RIGHT EYE. EMPLOYEE WENT TO HOSPITAL AND WAS EXAMINED. NO METAL WAS FOUND, BUT THERE WAS A SLIGHT BURN. SAFETY GLASSES WERE BEING WORN.

EE WAS CUTTING A PIECE OF METAL WHEN A HOT SLAG LANDED INTO HIS LEFT EAR EE DOUSED WITH WATER IMMEDIATELY. PROPER SAFETY EYE AND GLOVE PROTECTION WAS USED.

EMPLOYEE WAS WELDING VERICLE & OVER HEAD STRUCTURAL BEAMS.

EMPLOYEE WAS REMOVING A ROCK FROM A ROLL MILL. THEMILL DRIVE HAD BEEN DE-ENERGIZED AND LOCED OUT. HE THOUGHT THAT THE ROLLS HAD STOPPED COASTING. INSTEAD OF USINGA SCREW DRIVER TO REMOVED THE ROCK HE REACHED FOR IT WITH HIS HAD. THE MILL CAUGHT HIS THUMB AND FOREFINGER AND PULLED THEM BETWEEN THE ROLLS. HE LOST APPROX THE FIRST JOINT OF HIS THUMB AND ALL OF HIS INDEX FINGER ON R

CUTTING IRON ON CHOP SAW. A FOREIGN OBJECT FOT INTO LEFT EYE.

WHILE USING A TORCH TO HEAT A SPROCKET TO REMOVE SPROCKED FROM SHAFT. A CAN OF WD-40 SPRAY LUBRICANT FELL. THE CAN HIT THE SPROCKET PUNCTURED, AND THE CONTENTS FLASHED. THIS CAUSED NO PROPERTY DAMAGE AND 1ST AND 2ND DEGREE BURNS TO FOREARMSAND FACE.

INJURED WAS STANDING NEAR THE TRUCK HE WAS DRIVING WHILE IT WAS BEING LOADED WITH WET CLAY FROM A SETTLING POND.SOME FOREIGN PARTICLE GOT INTO HIS LEFT EYE.