Buscar en el registro

Right thumb caught in grinder. Right nail pulled off during incident. Required two stitches to stop bleeding.

Employee was cleaning shot cast nozzle and material blew into employee's right eye.

Employee was cleaning slots in division screen of #3 F/M using jackhammer. Small piece of metal went up under safety glasses sticking him on the right side of nose and a piece of metal ended up in left corner of right eye.

While using a jackhammer in cooler his left hand was on the handrail (scaffolding) and he was pulling back on the jackhammer with his right hand. When the jackhammer came loose the handle pinned his left hand between the handle and the handrail of the scaffolding.

Working on preheater with jackhammer, working in a rush. Poking on preheater and twisted in and upward motion & felt sharp pain on left side.

EMPLOYEE WAS DRILLING HOLES IN A PLATE OF 1/4" STEEL WITH A HAND DRILL MOTOR. THE DRILL BIT BOUND UP IN THE STEEL, CAUSING THE DRILL MOTOR TO KICK BACK, FORCING THE EMPLOYEE'S RING AND PINKY FINGERS BACKWARDS. HE WAS DIAGNOSED WITH A FRACTURE TO THE RIGHT RING FINGER.

Employee went to Stage #4 to blast an air cannon. He blasted the cannon and the sample port cap came off and sprayed employee with hot materials.

Employee was operating a jackhammer on the bypass at L2 preheater when he felt a sharp pain in his lower back. He immediately put the jackhammer down and started working with an air lance. The pain continued and employee was taken to doctor.

Employee claims he was using an oxyacetylene torch to cut duct work from top of finish mill. Pieces of hot slag allegedly entered employee's shirt through a gap in the sleeve and caused burns to forearm area. Employee failed to report injury and burns became infected, causing employee to seek medical treatment a week after injury.

EE WAS CLEANING BYPASS AREA. JACKHAMMER GOT STUCK IN BUILDUP. WHEN EE PULLED ON THE JACKHAMMER, THE LOCKING LATCH THAT HOLDS THE BIT OPENED AND THE BIT FELL OUT OF THE JACKHAMMER AND STRUCK THE TOP OF EE'S RIGHT HAND.

Employee claims that while air lancing sand silex, he got sand in both eyes.

WHILE FIRING THE CANNONS ON LINE #2, EE HAD TO LOOK UP AND REACH OVERHEAD. WHEN ONE OF THE CANNONS FIRED IT DISLODGED LOOSE MATERIAL THAT FELL INTO EE'S LEFT EYE.

EE WAS CUTTING WITH A TORCH & WAS HOLDING TORCH AT HIS SIDE. ANOTHER EE CLIMBED THRU SOME BRACING & HIS LEFT ARM CAME INTO CONTACT WITH LIT TORCH.

EE WAS POKING OVERHEAD WITH AIRLANCE AND CHUCK BROKE LOOSE & HIT HIS RIGHT KNEE.

LABORER WAS USING AN 8' JACK HAMMER. AS HE TURNED TO HIS RIGHT SIDE HE FELT A PAIN.

EE WAS CLEANING TAKE OFF DUCT. IT WAS FULL OF BUILD UP SO IT BLEW OUT AND COVERED HIM ON HIS GLOVES & COAT. THE MATERIAL GOT IN HIS GLOVE & BURNED HIS RIGHT HAND.

EE WAS CHECKING THE TOWER AND THE AIR CANNON WENT OFF - CAUSING HOT MATERIAL TO FLY OUT AND BURN HIS FACE & CHEST.

WORKING ON CUTTING UP A BIN. LOOKED UP IN THE BIN AND SOME DEBRIS FELL DOWN AND INTO EE'S RIGHT EYE. EYE PROTECTION WAS IN PLACE. HARD HAT WAS IN PLACE.

THREE WORKERS WERE REMOVING A FINISH MILL SHELL DOOR USING AN OVERHEAD CRANE TO SECURE THE DOOR ONCE THE CRABS HOLDING IT WERE REMOVED. AFTER EXERTING PRESSURE ON THE DOOR SO THAT IT WOULD FAL L A FEW INCHES INTO THE MILL, ONE WORKER GOT TOOCLOSE TO THE CRANE SHEAVE, WHICH HIT HIS SHOULDER. HE LOST HIS BALNCE & FELL HEAD FIRST 4-5' UNTIL CAUGHT BY HIS LANYARD: STRUCK PROTUDING NUTS

EE WAS USING A GRINDER TO SMOOTH OUT 1/8" STEEL PLATE. PLATE CAUGHT IN GRINDER AND PULLED LEFT THUMB INTO GRINDING WHEEL CAUSING SKIN ABRASION AND PARTIAL LOSS OF THUMB NAIL.

EE WAS USING METAL LATHE. HE WAS DISTRACTED FOR A MINUTE WHEN HIS HAND CONTACTED THE TURNING LATHE.

EE WAS LAYING ON HIS SIDE IN THE SHOP TO CUT MATERIAL WITH OXY/ACE TORCH. HE WAS WEARING A WELDING HOOD. MOLTEN MATERIAL SPLATTERED AND RICOCHEYED OFF ADJACENT SURFACE AND FELL INTO HIS LEFT EAR.

ELECTRICIANS WERE INSPECTING A THERMOCOUPLE ON THE LINE 1 ALKALI BAGHOUSE INLET. THEY DESCENDEDA LADDER TO REACH THE THERMOCOUPLE. WHILE WALKING ALONG THE WALKWAY TO THE THERMOCOUPLE, EE WAS EXSPOSED TO A COUPLE OF "PUFFS" OF BAD SMELLING HOT GAS. BAGHOUSE AND DUCT IS NORMALLY UNDER A SLIGHT VACUUM. HE FELT NO DISCOMFORT AFTER THE EXPOSURE, BUT REPORTED IT TO HIS SUPERVISOR.

THE EE WAS WELDING OVERHEAD WHEN A HOT BEAD OF METAL WENT INTO HIS LEFT EAR AND BURNED THE INNER CANAL BACK TO THE EARDRUM.

EE WAS GRINDING W/4" GRINDER THAT HAD A WIRE WHEEL ATTACHED. EE WAS WEARING A PLASTIC PONCHO TO PROTECT FROM WEATHER. GRINDER GOT CAUGHT IN PONCHO & EE LOST CONTROL CAUSING GRINDER TO STRIKE H IS CHIN. THE FACE SHIELD HE WAS WEARING PREVENTED MORE SERIOUS INJURY.

EE WAS USING JACKHAMMER TO CLEAR PREHEAT TOWER ON LINE #1 WHEN HE FELT A STRAIN IN HIS LOWER BACK.

EE RAISED HIS LEFT HAND TO PROTECT HIMSELF FROM BEING STRUCK BY A FALLING AIR LANCE (10' LONG, 1INCH STEEL PIPE). HIS LEFT THUMB WAS BENT BACK, STRAINING THE MUSCLES IN THAT AREA.

EE WAS REMOVING REFRACTORY FROM THE DAMPER AT THE RAW MILL DUCT & THE JACKHAMMER SLIPPED OFF THEREFRACTORY CATCHING EE'S RIGHT INDEX FINGER BETWEEN THE DAMPER & JACKHAMMER

AT APPROX 8AM ON 6/14/00, EMPLOYEE REPORTED SORE MUSCLE IN RIGHT ELBOW AREA FROM JACKHAMMERING THAT WAS DONE ON THE LINE # PREHEATER ON 6-13-00.

WHILE EE WAS JACKHAMMERING ON FLOOR C ATOP PLATFORM @ PRHEHEATER JACKHAMMER CAME LOOSE FROM BIT & EE FELT A TWIST IN BACK WHEN TRYING TO KEEP HIS BALANCE JACKHAMMER BIT POSITIONED TOO CLOSE TO EDGE OF HOLE. BIT CLIP HIT EDGE OF HOLE LOOSENING BIT

EE WAS WELDING PATCH OVER CRACK IN EAST END OF COOLER WHEN DRAFT WENT SLIGHT POSITIVE SLINKE DUST BLEW OUT OF CRACK AND BOUNCED BEHIND WELDING HOOD AND SAFETY GLASSES AND INTO RIGHT EYE.

EE WAS GRINDING & GOT DEBRIS IN HIS R EYE & FAILED TO REPORT THE ACCIDENT FOR 5 DAYS

EE WAS RUNNING A GUNNING MACHINE. THE COMPRESSED AIR LINE SEPARATED AND STRUCK EE ON THE SIDE OF HIS FACE. GUNITE MACHINE WAS BRAND NEW. APPEARS TO BE MANUFACTURING ERROR.

EE WAS WALKING THROUGH AN AREA WHERE PEOPLE WERE GRINDING. HE FELT SOMETHING IN HIS EYE BUT THOUGHT HE HAD GOTTEN IT OUT. 3 DAYS LATER HE REALIZED HE HAD NOT. HE DID HAVE ON HIS SAFETY GLASSES .

EE GRINDING AND METAL BECAME EMBEDDED IN EYE.

EMPLOYEE REACHED THROUGH ACCESS DOOR ON THE SIDEOF THE PRIMARY CRUSHER HOPPER AND WAS CHIPPING ON A LARGE ROCK WHEN ANOTHER ROCK FROM UP ABOVE FELL CRUSHING RIGHT THUMB BETWEEN ROCK AND CHIPP ING GUN.

EMPLOYEE STANDING IN FAB AREA WHILE ANOTHER EMPLOYEE WAS GRINDING AND DEBRIS FROM THE GRINDER GOT INTO HIS RIGHT EYE.

MISSED STEP ONTO BEAM AND STRUCK SHIN ON BASE PLATE.

EMPLOYEE WAS HOLDING AN AIR HOSE FOR A MAN USING AN AIR GRINDER, A PIECE OF SHAVING BLEW INTO HIS EYE.

WHILE LOWERING THE CATWALK ON DRILLING RIG, EE WAS PRYING THE CORNER OF THE CATWALK. THE WELD ON THE HINGE BROKE CAUSING THE CATWALK TO GIVE WAY EE FELL APPROX 4 FT. STRIKING THE RIGHT SIDE OF HIS HEAD ON THE HANDRAIL BRACE OF HIS HEAD ON THE HANDRAIL BRACE

EE WAS INSTALLING GUARD ON BUCKET ELEVATOR 09-046, WHEN HE LOST HIS BALANCE. HE LAID HIS RT HAND ON THE RAIL TO REGAIN HIS BALANCE AND A WHEEL RAN IT OVER,CAUSING A FRACTURE TO HIS RT THIRD FI NGER.

WHILE ARC GAUGING A PIECE OF HOT SLAG FELL INTO EE'S EAR.

EE WAS LEADING A PIECE OF PLASTIC WITH LEFT HANDIN TOWARDS SAW BLADE TO CUT IT WHEN THE PIECE OFPLASTIC JERKED & PULLED INJ LEFT HAND TOWARDS BLADE CUTTING TIP OF MIDDLE FINGER.

AFTER WELDING PIPE NIPPLES ON WATER TANK, EE REMOVED SAFETY GLASSES AND LAID HEAD ON FLOOR TO LOOK UP AND INSPECT WELD WHEN SLAG POPPED OFF AND HIT EE IN THE INSIDE CORNER OF HIS RIGHT EYE.

CLEANING PRE-HEATER WHEN FAN FELL CAUSING SYSTEM TO GO POSITIVE & BLOWING DUST.

EMPLOYEE LOST CONTROL OF AIR HOSE AND KNOCKED HIMSELF OFF 6' SCAFFOLD. EMPLOYEE WAS FURNISHED A SAFETY HARNESS BUT HE WAS NOT WEARING IT.

EMPLOYEE WAS CLEANING BUILT UP CASTABLE FROM PADDLE TYPE MORTAR MIXER. ASSUMPING THAT HE HAD IT CLEAN ENOUGH FOR THE PADDLE TO TURN THE EMPLOYEE CRANKED THE MIXER WITH THE BARREL OF THE MIXER IN THE DUMP POSITION AND ENGAGED THE PADDLES WHILE HOLDING THE BARREL OF THE MIXER. PADDLES WERE NOT FREE TO MOVE, RESULTING IN THE BARREL RETURNING TO ITS UP RIGHT POSITION, KNOCKING THE EMPL

EE WAS DRILLING HOLES IN A STEEL GUARD FOR THE TRIPPER 04-004 USING A BLACK AND DECKER 1/2" T HANDLE DRILL WHEN THE DRILL BOUND UP. THE DRILL SPUN AROUND AND HIT THE EE IN THE SIDE OF HIS HEAD ABOVE HIS LEFT EYE CAUSING A LACERATION WHICH REQUIRED FIVE STITCHES.

WAS WALKING BY PREHEATER & AS HE WAS PULLING DOWN FACE SHIELD A PORE HOLE SHOT OUT DUST & HIT ON LEFT EYE AROUND GLASSES

WHILE WORKING IN AREA AROUND THE RAW MILL, EE GOT SOMETHING IN HIS RIGHT EYE.