Buscar en el registro

A pallet jammed in palletizing machine B when the employee tried to remove the pallet a piece of the pallet broke off and EE's right hand hit the pallet above causing pain and swelling.

An employee felt pain in back during shift.

The employee was unblocking a feeder duct with water and air. When the employee applied air pressure, suddenly hot water comes out of the duct affecting his right forearm resulting in first and second degree burns.

EE se encontraba en el enfriador de clinker cortando con oxigeno y acetileno cuando un pedacito pequeno de escoria le cayo dentro del oido derecho. (EE was in the cooler of the clinker cutting with oxygen and acetylene when a small bit of slag fell inside his right ear.)

While the pump's material flew and hit right eye.

The employee was trying to repair a machine in movement and he was punctured with machine's grill.

EE was trying to start a welding machine. The machine backfired causing first and second degree burns in both ears, neck and top of the head.

EE attempted to dislodge a paper bag which was pinned in the packing machine. When opening the top to gain access to the pinned bag the electrical power automatically shuts down as a safety measure but apparently the air lines maintained pressure causing the rake to move foward when he was removing the bag causing him an open wound.

Employee was walking near a valve with controls heated powdered material at the Preheater area. Accidentally the valve failed momentarily and allowed the heated material to escape causing him burns in his right arm.

Employee was operating a forklift at the Packing House area. Suddenly he saw a defective cement bags pallet inside the palletizer. He entered inside the palletizer avoiding the safety devices used to stop the machine. The pallet continued its movement pinching accidentally his index finger between the pallet and a conveyor roller.

Employee was cleaning a forklift with a pressure washer. Accidentally he pointed the washer spray gun towards his left arm causing him an open wound.

Inj ee and another employee was adjusting the blades of packer machine #2 at the packing House area. Suddenly the employee just by him moved the blades manually pinching inj ee's middle right finger between the blade and the blade's housing. The equipment was electrically locked -out

EE was cutting with acetylene a piece of metal. Another worker ask him to use briefly the equipment. When EE received again the torch, he grabed it by a hot point causing him a burn in his right hand.

Employee was removing metal plates inside the cement Mill # 12, using a mechanical jack and a hydraulic jack for the removal of the plates. When pressure was applied to the plate the hydraulic jack slipped hitting him in the upper lip.

Employee was performing cleaning duties with a chipping hammer at Kiln area. After a while a hard piece of cement accumulated from a high part of the structure fell down due to vibration of the hammer. The cement struck employee in his right cheek.

Employee was repairing broken sampling equipment at the Preheat Tower. When he finished the task, suddenlly a pinion of the sampling equipment began to twirl pinching his left index finger.

Employee was using a crane to lift a metal drum filled with iron balls used on the Cement mills. Suddenly his little finger was pinched between the pulley and the wire rope of the crane causing him an open wound. He was using safety gloves.

EE WAS WASHING UNIT 003 WITH PRESSURED WATER. WHEN HE WAS CHANGING THE HOSE TIP HE ACCIDENTLALLY ACTIVATED THE HOSE HANDLE RECEIVING A JET OF WATER PRESSURE DIRECTLY ON HIS LEFT INDEX FINGER C AUSING HIM AN OPEN WOUND.

WHILE CUTTING DOWN A SCAFFOLD MADE OF PIPE WITH A CUTTING TORCH, THE EMPLOYEE TOUCHED A PIECE OFPIPE, RECIEVING A BURN IN HIS LEFT ARM.

EE WAS PACKING CEMENT BAGS AT THE PACKING HOUSE. SUDDENLY TWO FILLED CEMENT BAGS PINCHED HIS RIGHT FOOT AND TWISTED HIS KNEE WHEN THE BAGS MOVED ALONG THE CONVEYOR CAUSING HIM PAIN.

WHILE BUILDING A SCAFFOLDING THE WORKER BURN HIS RIGHT ARM WITH A PIECE OF PIPE HE JUST FINISHED CUTTING.

EMPLOYEE WAS CLIMBING DOWN FROM A DIGGER HE WAS WASHING WHEN HE ACCIDENTALLY GRASPED THE CONTROLTHAT ACTIVATES A HYDRAULIC JACK. WHEN THE JACK LIFTED UP, IT PINCHED HIS LEFT ANKLE.

EE WAS CUTTING AN IRON PLATE WITH OXY-FUEL GAS CUTTING EQUIPMENT. WHEN HE WAS CLEANING THE TORCH SCORIA WITH HIS HAND ACCIDENTALLY THE EE ACTIVATED THE TORCH AND THE FLAME BURNED THE WELDING G LOVE SEAM. THE FLAME PASSED THROUGH THE SEAM OPENING CAUSING HIM BURNS IN HIS FINGER.

EMPLOYEE WAS REMOVING A STEEL BEAM FROM KILN'S #6 CLINKER COOLER. THE BEAM WAS ATTACHED TO A HOIST AND HAD ONE OF ITS ENDS STUCK IN THE FLOOR. WHEN HE PULLED THE BEAM IT BECAME UNLODGED AND PU SHED HIM. HE LOST HIS BALANCE AND FELL TO THE FLOOR WHERE THE BEAM PINCHED HIS LEFT HAND WITH ANOTHER BEAM.

EE WAS WORKING IN THE START UP OF KILN #6 BURNER WHEN AN EXTENSION PIPE USED DURING THE START UP WAS BEING PULLED OUT OF THE KILN'S HOOD. HE OBSERVED THE PIPE SLIPPING INTO THE HOOD AND INSTIN CTIVELY GRABBED THE HOT PIPE CAUSING BURNS ON HIS RIGHT HAND.

EE WAS BUILDING A LUMBER MOULDS TO POUR CONCRETE INSIDE THEM. WHILE HE WAS DRILLING, THE AUGER TRESPASSED THE LUMBER CAUSING AN OPEN WOUND ON THE HAND HE WAS USING TO HOLD THE LUMBER.

EE WAS CUTTING AN IRON TUBE WITH AN OXYGEN-FUEL GAS CUTTING EQUIPMENT. SUDDENLY, SLAG FROM THE IRON TUBE, FELL INSIDE HIS LEFT WELDING GLO9VE CAUSING BURNS IN HIS LEFT WRIST. \

EE WAS WALKING BELOW A SCAFFOLD AT THE ENTRANCE OF KILN 6, WHILE OTHER EE WERE WELDING AT THE TOP OF THE SCAFFOLD. SUDDENLY WELDING SCORIA FELL ON HIS NECK CAUSING HIM A BURN.

EE WAS REMOVING CEMENT WITH A CHIPPING HAMMER IN THE MILL #12 AREA. WHILE HE WAS PERFORMING THE TASK CEMENT PARTICLES FELL ON HIS NECK, ARMS AND FACE CAUSING HIM ITCHING AND IRRITATION.

PLEASE, SEE ATTACHED: EE WORKING ON REINSTALLATION OF CEMENT MILL BEARING COVER WHICH WA RESTING ON THE FLOOR. WHEN IT WAS RAISED, IT SHIFTED SIDEWAYS & EE TRIED TO STABILIZE IT, & HIS RIGHT H AND WAS CAUGHT BETWEEN THE COVER & A BEAM. ER X-RAYS WERE NEGATIVE. RETURNED TO DUTY. FOLLOW UP VISIT X-RAYS REVEALED A MAYOR TRAUMA IN HIS RIGHT HAND FOR WHICH HE WAS PUT ON MEDICAL REST.

EE WAS REMOVING CEMENT FROM PIPES USING A GRINDER WITH A WIRE WHEEL BRUSH WHEN A WIRE FROM THE WHEEL BRUSH STRUCK AND EMBEDDED ITSELF INTO HIS LEFT LEG. HE DID NOT REPORT THE INCIDENT TO HIS S UPERVISOR OR OTHER PERSONNEL. ON 11/25/97 FOR THE FIRST TIME HE REPORTS HIS INJURY TO OUR MEDICAL PERSONNEL WHO SENT HM TO THE STATE INS FUND.

EE WAS GRINDING A METAL PLATE WHEN HEE FELT AN OBJECT IN HIS EYES.

EE WAS DRILLING OUT A BROKEN SCREW FROM A BOOSTER WHEN IT CAME OUT OF THE VISE IT WAS IN AND STRUCK HIM ON THE NOSE.

EE WAS GRINDING A SHIM ON A GRINDING WHEEL WHEN HE ACCIDENTLY GRINDED HIS RIGHT INDEX FINGER.

EE REMOVED HIS WELDING GOGGLES CAUSING DUST ACCUMULATED ON THE GOGGLE AND HIS FOREHEAD TO FALL INTO HIS RIGHT EYE. EE HAD JUST FINISHED CUTTING, WITH ACETYLENE/OXYGEN EQUIPMENT, A HOLE IN THE PRIMAR ELECTROSTATIC PRECIPITATOR SCREW CONVEYOR WHEN HE REMOVED THE GOGGLES.

EE WAS DOING CLEANING DUTIES IN THE HAMMERMILL THAT WAS GRINDING CLINKER. CLINKER PARTICLES FELL ON NECK AND HAND CAUSING ABRASSION.

HE WAS POLISHING A METAL SHEET WHEN SUDDENLY THE POLISHING MACHINE STUCK AND HIT HIM ON HIS LEFT LEG.

EE WAS PULISHING A WELDING ON A BRIDGE FROM CRANE. AND USING HIS SAFETY GLASSES A FOREIGN OBJECT WAS IMBEDDED ON HIS LEFT EYE. HE FELT DISCONFORT AFTER THE JOB WAS COMPLETED.

INJURED WAS DOING WELDING DUTIES INSIDE NO.6 KILN COLLER WHEN SUDDENLY SLIDE WITH A SMALL CLINKER BALL AND TEARING HIS RIGHT ANKLE.

HE WAS CUTTING WITH ACETYLENE A METAL MOBILE CRANE PART. WHEN HE WAS MOVING THE PIECE OF METAL, THE HOT SIDE OF THE CUTTING AREA TOUCH HIS RIGHT FOREARM.

EMPLOYEE WAS CUTTING WITH ACETYLENE A SHAFT IN NO. 3 OVERHEAD CRANE WHEN SUDDENLY A HOT METAL PART SLIDE IN HIS RIGHT BOOT.

EE WAS CUTTING IWTH ACETYLENE EQUIPMENT FORM #10 MILL NORIA SOME SCREWS WHEN SUDDENLY A HOT METAL PART INTRODUCED IN THE LEFT SAFETY BOOT, INFLICTING A SECOND DEGREE BURN ON HIS LEFT FOOT.

EE WAS HOLDING A METAL PART TO A WELDER, WHEN SUDDENLY LITTLE PIECES OF HOT MATERIAL SLIDE INTO HIS RIGHT BOOT.

EE WAS DISCONNECTING THE NUMBER TWO DRIVE COOLER AT KLIN NO. SIX WITH AN AIR PRESSURE HAND TOOL, WHEN SUDDENLY THE AIR LINE PIPE CAME OFF FROM THE OTHER LINE CONNECTION, HITTING HIM ON THE CHI N.

EE WAS CUTTING NUTS FROM THE AIR SLIDE OF NUMBER SIX BALL MILL NORIA, WHEN SUDDENLY THE AIR SLIDE MOVED AT ONE SIDE HITTING EE WITH A SMALL PIPE WITH A CAP HAS OUTSIDE OF THE CAGE AND INFLECTE D HIM AN INJURY.

HE INFORMS HE WAS CUTTING SOME METAL PLATES, WHEN SUDDENLY A METAL PARTICLE GOT INTO HIS RIGHT EYE.

DRILLING A STEEL BEAM WITH A HAND DRILL. SUDDENLY A METAL PARTICLE INCRUST LEFT EYE.

HE INFORMS HE WAS HELPING HIS PARTNER CUTTING A CLINKER NORIA WITH ACETYLENE & SOME HEAT PARTICLE FALL AWAY CAUSING HIM BURNS OF FIRST & SECOND DEGREE ON HIS RT ANKLE

CLEANING KILN #6 ALKALI BY-PASS AREA,SUDDENLY A FOREIGN BODY HIT RIGHT EYES.

HE AFFIRMS HE WAS WELDING AND A PIECE OF HOT PARTICLE GOT INTO HIS LEFT EAR.