Buscar en el registro

Employee was using a cordless drill. EE was drilling and when EE got to the end of the hole it hung up and twisted EE's wrist causing a sprained right wrist.

did not follow correct procedures

While swinging the 103 hoist crane around with a load on the hoist, EE was pulling from a rope and co-worker was assisting to swing the crane by pulling from the hoist chain. The rope broke. EE fell backwards onto the Nordberg crusher. Adjustment ran. EE fractured left side ribs.

While cutting steel in a band saw a small amount of steel particles built up close to the blade drive pulley. Employee lift guard and went to clear build up with finger, saw blade caught glove and pinched index finger tip of the left hand on edge of saw frame.

Employee felt and heard a tearing sound from the left shoulder while working the lever back and forth of a 1/4 ton chain come along. Employee was in the act of removing a rod assembly from a hydraulic cylinder. The hydraulic cylinder was laying horizontally in the shop on the cylinder work bench.

While EE was filling 5 gal bucket with soap and exiting an area where other containers were stored, his foot was caught on said containers and caused ee to trip. As he was falling his left forearm contacted a hot muffler on steam cleaner. This caused 2nd degree burns to effected area.

EE was replacing the rear spray bar. On water truck 21-1003, after cutting old spray bar off. He was grinding to prepare for new spray bar. He was wearing safety glasses and face shield when foreign object got in right eye.

While changing batteries in a truck using a socket and butterfly air ratchet, the socket fell off of the air ratchet. When trying to put the socket back onto the rachet, he accidentally bumped the air rachet trigger mechanism, causing the socket to spin lacerating the palm of his right hand resulting in four stitches.

EE was adjusting dust control water valve at the blue rock jaw crusher as a loader dumped rock into the plants feed hopper, a small flying rock struck and scratched his left eye. EE's prescription glaases did not come with side shields.

EE was adjusting the open setting of a 48" gyradisc crusher to assist with the unplugging of the machine. When changing the position of the crusher's hydraulic ram his left long finger got caught between the cylinder and the ram head injury was diagnosed as a left long finger crush injury on 5/12/06. EE was placed on medical duty.

WHILE OPERATING ENGINE LATHE, A LONG, SHARP SHAVING FLEW OUT AND LACERATED EE'S RIGHT MIDDLE FINGER.

Operating a milling machine and handling various tools and materials a small piece of metal lodged into right hand.

EE BEGAN TO AIR TIRE UP. HE PLACED BEAD BLASTER TANK ONTO TIRE AND OPENED VALVE. EE FELT SOMETHING GO INTO HIS EYE UNDER HIS SAFETY GLASSES.

OPERATING 4 1/2' GRINDER FOR LONG PERIODS OF TIME. FOREARM WAS SORE AND PAIN NEVER WENT AWAY.

CUTTING WITH A TORCH AND A PIECE OF MOLTEN METAL BURNED THROUGH SOCK AND BURNED FOOT.

(EE WAS OPERATING LATHE.) CHIP WOUND DOWN INTO CHIP PAN, GRABBED THE CHIPS IN PAN AND THE ROTATING CHUCK ON THE LATHE CAUGHT THE CHIPS AND PULLED THEM OUT ONTO EE'S HAND, CAUSING CUT.

EMPLOYEE WAS IN TRUCK SHOP DEBURRING PUNCH HEAD ON BENCH GRINDER. PUNCH SLIPPED OFF OF GRINDING WHEEL AND LEFT LITTLE FINGER CONTACTED GRINDING WHEEL, CAUSING ABRASIONS TO HIS LEFT LITTLE FINGER.

DURING PLANT REPAIRS USING 3/4" DRILL, THE DRILL TWISTED & WENT INTO SHARP STEEL. CUT HIS RT. PINKY FINGER & HAD TO HAVE 4 STITCHES.

Grinding on excavator bucket when foreign object entered left eye.

EMPLOYEE WAS USING A HAND HELD GRINDER ON A SPLICE WHEN THE GRINDER KICKED OUT CAUSING LACERATION ON LEFT INDEX FINGER. EMPLOYEE HAD REMOVED GUARD FROM THE GRINDER PRIOR TO STARTING THE JOB.

Working on conveyer cutting frame with cutting torch, pushed hose away and right hand ran across torch.

WHILE CUTTING A PIN OUT WITH THE TORCH A HOT PIECE OF METAL FELL CENTO GLAREE AND BURNED RIGHT HAND.

WHILE GRINDING A PIECE OF STEEL FLEW IN RIGHT EYE.

HE WAS LYING ON HIS LEFT SIDE CUTTING SOME SUPPORTS WHEN SPARKS POPPED BACK AT HIM AND WENT DOWN HIS RIGHT EAR CANAL.

GREASING EQUIPMENT AND HAND WAS CAUGHT BETWEEN LEVER ON GREASE GUN, HOSE REAL RETRACTED, PULLING HAND BACK.

GRINDING ON WINDOW SEAL AND A PIECE OF METAL WENT INTO R EYE.

CLEANING THROAT OF CRUSHER ABOVE THE ROTOR WITH A 6 FT BAR. THE BAR SLIPPED AND HIT THE DISTRIBUTOR PLATE AND GOT INTO ROTOR - IT WAS STILL SPINNING. IT WAS STILL IDLING DOWN. SMASHED HIS RIGH T THUMB AND HIT HIM BEHIND LEFT EAR.

WHILE EE WAS CHIPPING THE FEEDER PAN A LARGE ROCK FELL FROM THE EDGE AND STRUCK HIM IN THE BACK.

EE WAS DISASSEMBLING TURNBUCKLES FOR HAUL TRAILERS DUMP DOORS WITH A ROSEBUD TORCH AND A LARGE PIPEWRENCH. HE WAS HEATING THE TURNBUCKLE JAM NUT WITH TORCH IN LEFT HAND WHILE TURNING THE NUT W ITH THE WRENCH IN HIS RIGHT HAND WHEN HE PULLED THE TORCH AWAY FROM NUT. THE FLAME PASSED OVER HIS RIGHT HAND.

WORKING TO REMOVE ESSENTRIC WITH IMPACT TOOLS & PRY BAR, SHOULDER STARTED ACHING.

GRINDING STEEL PLATE FOR SIDE OF BUCKET. GRINDING DUST FELL IN LEFT EYE. HE THOUGHT IT CAME OUT, BUT EYE STARTED TO FEEL WORSE OVER THE WEEKEND.

RT HAND STRUCK AGAINST HARD SURFACE WHILE HOLDING GRINDER.

WHILE DRILLING ON THE DRILL PRESS A PIECE OF SHAVING WAS GATTING BIGGER AND BIGGER IN AN ATTEMPT TO PUSH IT OUT OF THE WAY IT CURLED AROUND MY FINGER RESULTING IN A SEVERE CUT.

EMPLOYEE WAS GRINDING ON A PIECE OF STEEL, WITH SAFETY GLASSES IN PLACE WHEN A PARTICLE SOMEHOW FOUND ITS WAY INTO HIS LEFT EYE. THE EMPLYEE WENT TO THE DOCTOR AND HAD THE PARTICLE REMOVED.

TAKING OFF A CUTTING EDGE ON LOADER #17-365, HOLDING THE BOLT WITH HAND AND USING IMPACT WRENCH TO TAKE BOLT OFF AND THE BOLT CUT THOUGH MY GLOVE AND CUT MY HAND.

WHILE WORKING ON THE PRESS AT THE MACHINE SHOP, A PIECE OF STEEL SLIPPED OUT AND HIT HIM IN THE LEFT HIP.

BULLDOZER PUSHING SCRAPER & HIT SCRAPER TOO HARD& BUMPED IT. THIS CAUSED THE OPERATOR TO BUMP HIS KNEE CAUSING A CONTUSION ON LEFT KNEE Y

EE WAS GRINDING PIPE TO FINISH WELDING WHEN THE PIPE BROKE IN TWO. IT SPRUNG TO THE LEFT WHERE HE AND HIS LEGS AND IT KNOCKED HIM BACK IN THE DITCH.

EE WAS WELDING AT RECYCLE PLANT WHEN SOME WELDING SLAG GOT BY HIS SAFETY GOGGLES AND WENT INTO HIS LEFT EYE. EE STATES THE DISCOMFORT LEVEL IN HIS EYE GREW STEADILY WORSE AND ON 4-1-99 HE REQ UESTED TO BE SEEN BY A PHYSICIAN.

EE WAS BURNING OUT A PIN ON A PIECE OF EQUIPMENTWHEN HE HIT A GREASE POCKET WHICH BLEW HIM OUT OF THE AREA HE WAS WORKING CAUSING HIM TO STRIKE HIS HEAD ON THE EQUIPMENT & BURN HIS HAND.

WHILE WELDING RECIEVED FLASH BURN BY OTHER WELDER, TO CLOSE TO ME.

HE WAS USING A 1?2" ELECTRICAL HAND DRILL A BRACKET FOR AN ASPHALT VALVE THE BIT GOT HUNG AND HIS LEFT THUMB WAS CAUGHT IN THE HANDLE OF THE DRILL.

PULLING PLOW BOLTS OUT OF CUTTING EDGE. EE WAS HOLDING THE BOLT FROM THE BOTTOM, WHEN IT CAM OUT OF THE SLOT & IT SPUN, WHEN IT SPUN IT CUT THE MIDDLE FINGER ON THE LEFT HAND. HE WAS USING AN IMPACT WRENCH & HOLDING THE BOLT & WHEN IT SPUN HE WAS HOLDING THE BOLTS.

WHILE CHANGING A TIRE ON EQUIPMENT #71-917 THE HYDRALIC JACK SLIPPED OFF & THE BEAD HIT HIS HAND CAUSING INJURY.

EMP SLIPPED WHILE CRAWLING WITH A LIT TORCH BURNING OPPOSITE HAND.

EMPLOYEE REPORTED SORE BACK TO SUPERVISOR AT END OF SHIFT WHILE CUTTING WEEDS. EMPLOYEE DID NOTO REQUEST MEDICAL TREATMENT 5-28-96.

WHILE WELDING HE SCRATCH RIGHT ELBOW ON A PIECE OF IRON.

EMPLOYEE WAS GRINDING METAL FOR CONVEYORS IN THE BLENDING PLANT WHEN A PIECE (SPARK) FLEW INTO HIS EYE.

FLASH BURN OF EYES WHILE WELDING.

34339NG PIECE OF METAL IN THE MAIN PLANT SHOP. WHEN PIECE HE WAS CUTTING OFF STARTED TO FALL, HE HAD THE TORCH IN HIS LEFT HAND AND AS HE STEPPED BACK TO AVOID METAL, HE BURNED HIS RIGHT HAND 69380TORCH.