Buscar en el registro

Overcast skies, temperature is 70 degrees, little to no wind, work area clean of debris with a little buildup in the chute. Technician was welding in the chute, lost balance and fell to the screen below.

Little to no debris on or around accident

Operator had drilled approx. 16 feet of a 45 foot face when he noticed that part of the face had caved off to his right. He raised the drill stem and began to raise the outriggers when the drill slowly slid off the face and turned on its side. Since the boom was fully extended, it stopped the drill on the caved off material 20 feet from the floor.

Welding lifting eye on railcar and eye broke loose and hit employee on cheek.

EE was welding in the same area as two other welders and flash burned his eyes.

Employee was working inside the crusher on his hands and knees on a steel surface and bruised his knee.

Employee was holding a steel plate in place while another employee cut it with an acetylene torch. The torch slipped and burned his arm.

EE WAS WORKING IN THE PLANT AREA AND FELT SOMETHING BLOW INTO HIS EYE.

EE WAS OPERATING A SCRAPER AND STATED HIS BACK BEGAN HURTING EARLY IN THE WEEK AND CONTINUED TO GET WORSE AND THAT THE CAUSE WAS ROUGH ROADS, JERKY SHIFTING AND A BROKEN SEAT.

EMPLOYEE WAS WELDING WITH AN ARC WELDER, LIGHT FROM THE ARC CAUSED SKIN BURNS WHICH BECAME INFECTED.

EMPLOYEE WAS OPERATING A BOULDER BRAKER AND THE BIT SLIPPED OFF A BOULDER JOLTING THE MACHINE, EMPLOYEE FELT PAIN IN HIS ABDOMEN AND AGAIN LATER WHEN HE CLOSED THE CAB DOOR, THE PAIN CONTINUED TO GET WORSE DURING THE DAY.

EMPLOYEE WAS USING AN OVERHEAD CRANE TO SEPARATE TWO PIECES OF PLATE STEEL. THE CHAIN HOOK SLIPPED OUT AND HIT HIM ON THE LIP.

EMPLOYEE WAS WELDING INSIDE A HAMMER MILL WWITH ANOTHER WELDER AND FLASH BURNED HIS EYES.

EMPLOYEE WAS USING AN AIR CHISEL WHILE REPARING THE CRUSHER AND GOT A STEEL CHIP IN EYE.

EMPLOYEE WAS OPERATING A POWER GRINDER AND A PARTICLE CAME UNDER HIS HOOD AND HIT HIS EYE.

EMPLOYEE WAS LOADING MATERIAL ONTO A TRUCK WITH A CATERPILLAR EXCAVATOR, THE BANK HE WAS DIGGING COLLAPSED BREAKING HIS WINDSHIELD. THE FRAME ON THE WINDSHIELD HIT HIS KNEE BREAKING HIS KNEEC AP.

EMPLOYEE STATES HE FELT HIS NECK JERK WHILE HE WAS OPERATING A BOULDER BREAKER - HIS ARM AND SHOULDER BEGAN TO HURT WITH THE PAIN INCREASING OVERNIGHT.

EMPLOYEE WAS WORKING IN THE WELDING DEPARTMENT WHEN A PARTICLE OF RUST WAS THROWN INTO HIS EYE BY A HAND GRINDER BEING OPERATED BY ANTOEHR EMPLOYEE.

EMPLOYEE WAS CLEANING METAL PRIOR TO WELDING,THE HAND GRINDER SLIPPED AND CUT HIS KNEE.

EMPLOYEE WAS HELPING A WELDER REPAIR THE PLANT THE WELDER WAS MOVING THE TORCH TO THE OTHER SIDE OF THE EMPLOYEE & THE FLAME CROSSED HIS ARM

EE WAS SHARPENING A KNIFE ON A GRINDER AND GO T APIECE OF STEEL IN HIS EYE.

EE WAS REPAIRING A HEAVY METAL CHUTE IN THE SHOP HE WAS SUING AN OVERHEAD CRANE TO LIFT AND TURN THE CHUTE WHEN A CHAIN SLIPPED AND THE CHUTE FELL ON HIS FOOT.

EE WAS USING A POWER GRINDER WITH A CUP BRUSH TO CLEAN A PIECE OF PIPE, IT KICKED BACK AND HIT HIS KNEE CAUSING A CUT ON HIS KNEE.

EMPLOYEE WAS WELDING WHEN A SPARK BOUNCED INTO HIS EAR

DRILLING FOR CONSTRUCT, DRILL DRILLED IN VOID COMPRESSED AIR BLEW DILL CUTTINGS IN EMP FACE

EE WAS MOWING GRASS WHEN A PIECE OF DIRT FLEW INTO HIS EYE.

EMPLOYEE WAS WORKING IN THE SHOP WHEN HE NOTICED AN EYE IRRITATION THAT GRADUALLY BECAME WORSE

EMPLOYEE WAS RE1LACING A GUARD ON MOTOR PULLEY HE WAS USING THE POINT OF CHIPPING HAMMER TO LINE UP THE BOLT HOLES AND HIT THE CHIPPING HAMMER WITH ANOTHER HAMMER A PIECE OF STEEL BROKE OFF AND EMBEDDED IN3HIS HAND

EMPLOYEE WAS OP9RATING A GRADALL WHEN HIS BACK BEGAN TO HURT.

AFTER ADJUSTMENT WERE MADE ON A NEWLY INSTALLED OVERHEAD CRANE I,NAME WAS OBSERVING THE UNIT IN OPERATION. I,NAME STANDING ON THE CATWALK NEXT TO THE TROLLEY RAIL HAD HIS LEFT ARM AND HAND RAN OVER BY THE TROLLEY WHEEL, BREAKING BONE IN HAND AND DAMAGE TO SKIN ON HAND, FOREARM.

EMPLOYEE LOST THE DRILL STEM IN THE DRILL HOLE. HE RECOVERED IT BUT IN THE PROCESS ROCK FELL INTO THE CENTER HOLE BLOCKING IT. HE REMOVED THE DRILL BIT AND THOUGHT THE AIR PRESSURE HAD BEEN BL ED OFF, WHEN HE REACHED OVER TO COVER THE END OF THE BIT WITH A CLOTH, ROCK BROKE LOOSE INSIDE THE DRILL STEM AND BLEW OUT HITTING HIS HAND.

THE EE WAS DRILLING A BOULDER WITH A JACKHAMMER--THE BOULDER SHIFTED & THE EE LOST HIS BALANCE & FELL HITTING HIS HEAD ON A ROCK.