Buscar en el registro

EE REPORTS WHILE WELDING ON TAILIN BOX, AN EXPLOSION OCCURRED.

EE REPORTS WHILE WELDING ON TAILING BOX, EE STRUCK ARCH WITH WELDER AND AN EXPLOSION OCCURRED.

EMPLOYEE REPORTS WHILE RUNNING BUFFALO MACHINE, HE SMASHED HIS RIGHT THUMB.

EE REPORTS WHILE REMOVING NUT WITH IMPACT WRENCH, WRENCH SPUN OFF HITTING EMPLOYEE'S FINGER.

EMPLOYEE WAS HOLDING TH THROTTEL OPEN ON A MILLER WELDING MACHINE SO ANOTHER EMPLOYEE COULD CHECK THE VOLTAGE OF THE MACHINE WHEN HIS HAND WEN TINTO THE FAN AND GOT CUT.

EMPLOYEE REPORTS WHILE GRINDING HE STOPPED TO CHECK PROGRESS, GRINDER CAUGHT THE EDGE OF THE STRUT EYE AND KICKED BACK, HITTING HIS ARM.

TIP OF STEAM CLEANING MACHINE BROKE OFF STRIKING EE IN LEFT EYE.

EE REPORTS WHILE PULLING BOOM OFF LOADER, PULLING CALLETES OFF BOOM PINS WITH IMPACT WRENCH, CALLETT WAS TIGHT, WHEN BROKE LOOSE IT SMASHED FINGER AND HAND AGAINST IMPACT WRENCH.

PERSON WAS WORKING AROUND A PLACE WHERE SOMEONE WAS WELDING AND LOOKED AT ARC.

EE CAME UPON PIPE GROVER ON A PIPE IT LOOKED AS IF IT WAS CLAMPED ON PIPE & TURNED ON GROVER & IT CAME OFF PIPE & GRABED FINGER OF EE.

EE WAS COMPLETING A 3516 ENGINE INSTALLATION. HE PLACED AJACK BETWEEN THE FRAME AND BELL HOUSIGN PUTTING TENSION ON THE JACK. HE USED A CRANE AND A CABLE WIHTA CAT LIFTING INK & BOLTED IT TOT HE CONVERTOR. HE WANTED TO PICK ENOUGH WEIGHT UP SO THEENGINE WOULD SLIDE. HE WAS FOSCUSED ON THE ENGINE MOUNT BUMPING THE CRANE UP WHEN HE HEAD OF THE BOLT CAME.

OPERATOR MOMENTARILY RAN TIP OF WATER BLASTER NOZZEL OVER HIS FOOT CAUSING AN APPROXIMATELY 2" LACERATION TO HIS BIG TOE. OPERATOR FOLLOWED ALL SAFETY PROCEDURES EXCEPT HE DID NOT WEAR STEEL T OED BOOTS.

EMPLOYEE WAS STARTING THE POWER TROWEL WHEN HE PULLED THE CORD ON THE POWER TROWEL THE CORD KICKED BACK & BROKE HIS RT HAND RING FINGER

WAS CHANGING BUSHING BIT ON CHIPPING GUN DID NOT SHOT AIR SUPPLY BUSHING BIT BROKE(SHARP PART) & STRUCK EMPLOYEE SAFETY GLASSES RIM OF SAFETY GLASSES CAUSED LACERATION UNDER RT EYE

EMPLOYEE REPORTS THAT HE WAS OPERATING A CAT PUSHING MATERIAL WHEN HE BACKED UP HE STATED THAT HE FELT SOMETHING SNAP & A SHARP PAIN START ED IN HIS BACK

THE JOB INVOLVED OVERHEAD WORK. DESPITE THE CONSTANT USE OF SAFETY GLASSES & FACE SHIELD, GRINDING PARTICLES ENTERED THE EYE & SCRATCHED THE CORNEA.

EE PUT PIPE WRENCH ON DRILL ROD TO BREAK IT LOOSE. DRILL ROD WAS STILL TURNING HE GOT HIS LEFT RING FINGER CAUGHT BETWEEN PIPE WRENCH TO DRILL MAST. SMASHING IT AND BREAKING THE BONE ON THE TI P OF HIS FINGER.

EMPLOYEE REPORTS THAT #4 SHOVEL WAS PULLING OUT TO MAKE ANOTHER SET UP ABOUT 400 FT. BACK TOWARD #1. EMPLOYEE WAS FLIPPED ON HEAD BY SHOVEL CABLE AT #4 SHOVEL.

EE REPORTS THAT 7 SHOVEL HAD A RUNAWAY IN SWING MODE CAUSING LOADED SHOVEL DIPPER TO SLAM INTO WABCO 18 WABCO 18 HAD ONE DIPPER OF MUCK IN IT WHEN THIS HAPPENED. EE WAS JARRED AROUND ROUGHLY I N CAB.

EE REPORTS THAT WHILE REMOVING TOOTH WITH DOUBLE JACKHAMMER TOOTH SHATTERED AND PIECE FLEW OFF AND ENTERED EE S LEFT ARM ON TOP OF ELBOW.

SHEAR BLADE CAME DOWN TO CUT A PLATE,KICKED THE PLATE UP THEN THE HOLD CAME DOWN PUSHING THE PLATE ON FINGERS.

54736YEE REPORTS THAT WHILE HOOKING UP TRACTOR TO RIPPERS ON GRADER 16 WITH TOW CABLE EMPLOYEE STEPPED BETWEEN GRADER AND TRACTOR,OUT OF SIGHT OF OPERATOR.BEFORE HE COULD STOP GRADER PINNED EM 73685E BETWEEN RIPPERS AND BUMPER.

EMPLOYEE REPORTS STANDING UP HOLDING A DRILL WITH RIGHT HAND AND DRIVING THE DRILL ONTO WOODEN POLE, EXPERIENCED A SUDDEN SHARP PAIN OF THE MUSCLES ON BOTH SIDES OF BACK FROM ABOVE WAIST UP TO SHOULDER BLADES. PAIN MADE HIM GO DOWN ON KNEES.

EMPLOYEE REPORTS GRINDING OUT A WELD INSIDE THE CAR BODY OF SHOVEL #1, A PIECE OF METAL IN LEFT EYE.

EMPLOYEE REPORTS TAKING OFF NUTS WITH IMPACT WRENCH, SMASHED RIGHT THUMB BETWEEN IMPACT WRENCH AND BEAM.

EMPLOYEE REPORTS STINGER HOLDING CABLE ON BACK OF SHOVEL SLIPPED INJURING 3RD, 4TH AND 5TH FINGERS.

EMPLOYEE REPORTS AT WASH RACK & AFTER FINISHING STEAMING LOADER SHE WAS STEAMING OFF HER RAINSUIT & RUBBER BOOTS ALLOWING STEAM TO GET DOWN INSIDE R UBBER BOOT

AT WELDING SHOP CUGTTING EXHAUST SYSTEM FORM WABCO CUT THROUGH SOONEER THAN ANTIC AND FELL ON L KNEE CASUSING LACERATION.

EMPLOYEE REPORT8 IN S4 SHOVEL, WAS SWINGING SHOVEL TO RIGHT AND HIT BOULDER CAUSING JARRING.

AT MACHINE SHOP3WORKING WITH A HYUDRAULIC PRESS WAS PRESSING A BUSHING IN END OF A TIE-ROD WHEN PRESSURE WAS RELEASED THE TIE-ROD TWISTED & ROLLED ONTO THE LEFT INDEX FINGER

EE WAS GRINDING3OVERHEAD. THE GRINDER DUG INTO A CRACK CAUSING IT TO TWIST OUT OF HIS HANDS & WHILE CAOSTING AT HIGH SPEED THE GRINDER STRUCK THE INSIDE OF HIS RT LEG CAUSING A LACERATION.

GOT FLASH BURNS3DIDNT USE ADEQUATE PROTECTION.

EMPLOYEE SAYS H9 WAS REMOVING A LUG NOT FROM A WABCO 170 WHEEL MOTOR WITH AN IMPACT WRENCH WHEN THE LUG STUD CAME LOOSE & BEGAN TO BACK OUT PINCHING FINGER BETWEEN WRENCH & LUG

EM 3 EMPLOYEE REPORTS LAYING HIS HAND ON TURBO TO BE CHECKED,FINGER WAS SUCKED INTO THE FAN BLADES.WO

A 572 G SIDE BOOM HAD CAUSED THE GROUND TO BE UNLEVEL. AS THE EMPLOYEE WAS CUT 36" PIPE HE TURNED ON HIS RIGHT FOOT AND TWISTED HIS KNEE.

EMP WAS ATTEMPT3NG TO REMOVE A MIXER SHAFT FROM AN ELECTRIC MOTOR USING A PIPE QRENCH WITH THE HELP OF ANOTHER EMPLOYEE. THE OTHER EMPLOYUEE PLUGGED IN THE MOTOR WHILE SHE WAS HOLDING ON THE P IPE WRENCH CAUS3NG IT TO FLIP AROUND AND HIT HER RIGHT ARM

EMPLOYEE WAS RIGGING A LOAD WHEN HE GRABBED THE LOAD CABLES WITH HIS LEFT HAND FOR SUPPORT AND BALANCE THE CABLE RAN HIS HAND INTO THE LOAD BLOCK PULLEYS

WHILE CUTTING 1/2 IN. PIECE OF PLATE, THE END THAT WAS CUT FELL FROM THE BACK OF THE WELDING TRUCK STRIKING THE LEFT FOOT.

OPERATOR WAS PUSHING UP A STOCKPILE OF DIRT FOR A FRONT END LOADER AND POSTIONED THE RT TRACK TOO CLOSE TO THE EDGE OF THE STOCKPILE THE DIRT SUPPORTING RT TRACK COLLAPSED CAUSING THE DOZER T O ROLL 180 ONTO ITS BACK

WELDING IN THE PIT AREA LEFT EYE FELT IRRITATED AS IF SOMETHING WAS IN IT