Buscar en el registro

EE had performed repairs on screw drive end assembly. When equipment started up, it locked down causing bolts to break that secured the drive assembly. The assembly rolled striking EE and knocking him to the floor.

Employee was operating 992 shovel in hard packed ground. Shovel was vibrating and shaking badly.

DRAWSTRING OF A RE-TIED BAG HUNG ON A BELT MOTOR CAUSING THE BAG TO BECOME UNBALANCED. WHEN THE BAGGING CYCLE ENDED THE BAG RELEASED AND FELL TOWARD EMPLOYEE. HE STEPPED BACK AS THE BAG FELL ON HIS FEET.(APPROX 2000#)AS HE MOVED HE FELT PAIN IN LOWER BACK. RESTRICTED DUTY REQUIRED.

EE WAS INSPECTING RELIEF VALVE ON #6 ATOMITE SILO. SILO HAD BUILT UP PRESSURE CASUING THE CAP TO BLOW OFF HITTING EE IN THE MOUTH

EE and coworker were welding to repair handrail. As they finished welding, there was a flash which burned ee's face and both forearms.

Employee was starting pump after repair. Pump seal failed causing product liquid (hot) to be blown onto employee's right abdomen,thigh,groin, and forearm resulting in burns; requiring medical treatment and restricted work duty.

EMPLOYEE ATTEMPTED TO ADJUST THE WEIGHT ON THE ATOMITE BAG PLACER. WHEN THE AUTOMATIC ARM TRIED TO PLACE A BAG, IT STRUCK EMPLOYEE SEVERAL TIMES. RESTRICTIONS BEGAN 8/19/04.

Ee was attempting to clean out the rotary air lock feeder by using his index finger. Resulted in amputation of end of right index finger. Ee will be out approx six weeks.

Employee was piggling line out to ultra fine. He was bleeding the pressure off the line. When he opened the cam-lock, pressure blew the line back and struck employee on the hand and wrist.

EE WAS PUTTING THUMPER ON #26 TUBE MILL WHEN IT TURNED, CAUSING ARM AND SHOULDER TO TWIST AND PULL. DID NOT REQUEST DR. VISIT UNTIL 12/8/03.

EE WAS INSTALLING A HAND RAIL. CUT A PIECE OF STEEL WITH A TORCH & ACCIDENTALLY LEANED AGAINST IT RESULTING IN 2ND DEG BURN TO RIGHT CHEST AREA

EE WAS CHANGING THE BAG CHAIR CYLINDER HEIGHT. ACCIDENTLY HIT START BUTTON ACTIVATING BAG CHAIR CYLINDER. MASHED THUMB, PULLED OFF THUMBNAIL.

EMPLOYEE HAD CUT METAL WITH TORCH. AFTER MAKING THE CUT, HE REMOVED GOGGLES TO INSPECT CUT. PIECE OF METAL "POPPED" OFF AND STRUCK HIS EYE.

EE WAS TURNING ROTATING ASSEMBLY IN RUMMING SEPARATOR. HE PINCHED HIS FINGER BETWEEN THE BLADE ON THE CLASSIFIER AND A BOLT INSIDE THE HOUSING. REQUIRED STITCHES.

EMPLOYEE WAS DISCONNECTING LINE FROM PUMP. LINE WAS UNDER PRESSURE AND BLEW OFF WHEN EMPLOYEE DISCONNECTED THE COUPLING. EMPLOYEE SHOULD HAVE TURNED OFF PUMP BEFORE DISCONNECTING LINE. SLURRY BLEW OUT OF LINE AND BURNED ARM.

EE WAS ADJUSTING THE BAG SADDLE ON THE MARBLEMITE BAGGER. THE CYLINDER PULLED IN, PINCHING HIS RIGHT THUMB BETWEEN THE CYLINDER AND THE METAL SADDLE.

EE WAS ATTEMPTING TO UNCLOG THE CS-11 VACUUM RECEIVER. HE REMOVED THE PLUG FROM THE AIRLOCK AND TRIED TO SHAKE OBSTRUCTION FREE BY HAMMERING THE CS-11 CONE. WHILE DOING THIS HE ATTEMPTED TO ST ABILIZE HIMSELF BY HOLDING ON TO THE AIR LOCK. HE ACCIDENTALLY PLACED HIS FINGER IN THE PLUG HOLE WHERE THE ROTOR CUT OFF THE END OF HIS FINGER.

EE WAS CHANIGNG A BLOWER PIPE IN SHIPPING WHILE THE BLOWER WAS ON. AS EE "WRESTLED" WITH THE PIPE, HE FELT SOMETHING PULL IN HIS BACK.

EE WAS BLOWING OFF AN AREA WITH AN AIR HOSE. COATED CALCIUM CARBONATE GOT INTO HIS RIGHT EYE.

EMPLOYEE WAS OPERATING THE 504 BAGGER AND WAS STANDING IN THE FOOTREST BAR ADJUSTING HIS SEAT. HIS FOOT SLIPPED OFF THE BAR, HE FELL ON THE CHAIN BELT AND HIE THUMB GOT HUNG IN THE BELT, WENT AROUND ONE OF THE DRIVE ROLLERS AND WAS RELAEASED.

OPERATOR WAS LOADING TRUCKS WITH 984 LIEBHERR SHOVEL WHEN A BOULDER FELL FROM TOP OF THE PILE. OPERATOR SWUNG HIS MACHINE AROUND AND CAUGHT THE ROCK IN THE BUCKET. WHEN THE ROCK HIT THE BUCKET THE WINDSHIELD SHATTERED AND A SMALL PIECE OF GLASS HIG EE IN THE EYE.

EMP WAS TIGHTENING THE LUG NUTS ON HAUL TRUCK WITH A ONE INCH DRIVE IMPACT WRENCH WHEN THE NUT BOTTOMED OUT AND WRENCH SNAPPED BACK AND TWISTED WRIST.

EE WAS UNDER THE #7 RAYMOND MILL ISNTALLNG BEARING AND BOTTOM PLATE. THE AIR HOSE TO THE WRENCH BLE WOFF AND WAS SHIPPING AROUND BLOWING DUST. ALL EMPLOYEES WERE GETTING OUT OF THE WAY OF TH E HOSE. THE BOTTOM PLATE AND BEARING FELL AFTER BEING HIT BY THE HOSE, INJURING EE'S LEFT LEG.

EMPLOYEE WAS WORKING ON AN 80G6 DUST COLLECTOR. WHEN THE SCREW DID NOT START HE PUT HIS HAND INTO TURN PULLEY. THE MOTOR STARTED AND THE BELT CAUGHT HIS FINGER.

EE WAS APPLYING HARD SURFACING TO THE FLIGHTS OF A CENTRIFUGE. HE DROPPED A RED HOT SECITON OF THE ROD ON HIS LEFT THIGH RESULTING IN A BUR AREA APPROX. THE SIZE OF A QUARTER.

WELIDNG IN WASHER DRUM INJ PROLB. CASUED BY RFECTING ARCS OFF OF DRM WALLS. WASHER DRUM IS 17'6 L BY 10' IN DIAMETER. BOTH EMP WEARING WELDING HELMETS