Buscar en el registro

As employee was swinging a 4-lb hammer to remove a plug from the #1 flash dryer product line blower, he felt pain in right shoulder.

Employee was working on sifter blower. Shaft of the motor was turning due to draw from dust collector. Employee attempted to slow motor to a stop by creating friction against shaft with pair of pliers. Pliers slid down shaft and hung on keyway. Inertia of shaft jerked pliers resulting in injury.

Employee injured while removing guard, guard slipped out of co-worker's hand transferring weight to injured employee.

While employee was removing a 120# bearing off the raymond mill drive, the sprocket began to fall. He attempted to hold it up to keep it from falling.

EE was using pry bar to line up poly pipes for connection. Bar slipped.

Employee was helping with cleanup around the #2 Flasy Dryer when he picked up a scrap screw and felt a pull in his lower back.

While checking the #36 Raymond Mill Feed Belt Tail pulley, employee slipped and pulled his left knee. Restricted duty began 11/27/07.

He was opening a lid and turned it the wrong way and pulled lower back.

Employee tripped over a box sticking out from under a table in the maintenance shop. Placed on restricted duty 11/20/07.

Employee picked up butterfly valve and turned and dropped it to the floor. Placed on restricted duty 11/27/07.

EE was training a belt at shipping, when he cut his left index finger on a sharp edge of a guard near the belt adjustment.

Employee bent over to pick up empty bag. As he bent over he twisted and pulled a muscle in his back.

He was climbing under and around machinery and pulled something in the groin area.

Employee was backing away from forklift in operation when he backed into the safety chain across the dock doors. The latch gave and employee fell approx. 6 ft to the ground.

Employee completed loading truck and stepped from back of truck to ground. Had pulley in left hand and lanyard in right hand to prevent feet from entanglement. When he landed on ground the pulley retracted and jerked left arm backward.

Employee was using personal pocket knife to dislodge pencil stuck in his hard hat. Knife slipped cutting hand. Required stitches, was not work related.

6/30/07 employee stepped on a pipe and rolled ankle. The following night (7/1/07) he stepped on a water hose and turned ankle again.

Dropped table bushing on fingers. 3 mashed fingers.

Employee tripped on a piece of metal attached to floor at Plt 3 504 Bagger. Injured fell against the spout on the 504 Bagger cutting his upper lip. Required stitches.

Employee was using pry bar to put cribbing under pipe. Strained back.

Employee tripped on raised forks of forklift.

Employee was descending the steps on Plant 2 #3 tube mill collector when he twisted his right ankle.

Employee was stepping off stairs onto track #3. Twisted right ankle.

IE was coming down ladder. Lost balance. Grabbed piece of tin cutting hand. Required sutures.

Employee was working on a feeder and had to remove a 2 HP motor and then re-install it.

Employee was exiting company vehicle. Door of vehicle slammed on finger.

Employee was pulling and lifting boxes of bags out of a manlift. He injured both shoulders.

Employee had descended stairs and stepped onto floor grate. Caught toe in floor grate and twisted ankle.

EE was running under a catwalk and raised up too quickly. Struck his head on catwalk and fell backward onto ankle.

Employee got into company vehicle, pushed himself back, and knee popped.

Employee was washing floor using a water hose. As he was backing up he stepped off a low retaining wall, straining his back. Refused medical treatment at time of accident. Sought medical treatment 12/11/2006.

Employee was pushing against pry bar. Bar slipped and employee fell forward striking left jaw on angle iron. Required 4 stitches.

Plant power outage caused pump to quit for the sand grinders. Employee opened lid to add water to the sand grinder when steam came out and burned left upper arm. (minor Burn)

IE was assisting in changing a spout blower on a bagger. He helped lift and carry blower to designated area.

Employee fell down the stairs at Plant 3 Shipping.

Employee was cleaning out the cone crusher at the East washer. He placed rock into a 2-gallon bucket while a co-worker pulled bucket full of rock out of crusher. A rock fell out of the bucket and struck IE's hand.

While operating the rock breaker, employee noticed a rock hung up in between the tracks and the cab. He attempted to remove the rock. When it came loose it mashed his right thumb into the cab of the rock breaker.

EE had performed repairs on screw drive end assembly. When equipment started up, it locked down causing bolts to break that secured the drive assembly. The assembly rolled striking EE and knocking him to the floor.

Employee was carrying a keystone valve while he was walking on a chain conveyor. He fell off chain conveyor and mashed his finger.

EE was reaching for air supply cutoff valve.

EE was lowering lid of bulk truck when he noticed the seal was about to fall into the truck. He released the lid to grab the seal and the lid continued to fall, crushing his finger.

Employee stepped off railcar into hole or rut. Twisted ankle.

Employee was changing product hose at plant 2 ultra fine plant. Hose slipped and struck employee's left leg.

Employee was changing the motor on a Syntron feeder. He pushed the feeder with his right foot.

Employee was operating 992 shovel in hard packed ground. Shovel was vibrating and shaking badly.

EE was replacing fork on the spray dryer when the fork slipped out of his hand and mashed his finger.

EE slipped and fell on 2nd or 3rd step from the bottom, landed on floor. Back hit corner of step.

Employee slipped and fell on wet surface. Had rained previously.

Employee was standing next to floor heater with hands behind back. He moved and right hand contacted the heater.

EE MASHED LEFT INDEX FINGER WHEN HE MOVED CHAIR TOO CLOSE TO BAGGER. FINGER CAUGHT BETWEEN CHAIR AND BAGGER.