Buscar en el registro

Employee backed into a lit cutting torch and burned the top portion of his right calf. He was taken to the doctor the following day and diagnosed with 1st and second degree burns.

Employee glared at welding arc and eyes began to burn.

Two EE's were placing 6" PVC pipe at a tire wash. After gluing into place, they were back filling a Bobcat. As EE swung the backhoe for more material, injured EE reached down and pulled up on the pipe, the bucket of the backhoe passed, caught the tip of EE's right index finger between it and the end of the PV pipe, cutting a piece of skin.

Employee was greasing rollers on dragline with an air accuated grease gun. Hose developed pin hole & grease filled his glove and (L) thumb because of extreme pressure. Employee had surgery to remove grease from around bone. He is off work presently.

EE was working with a zip gun removing material from a pipe. He felt sore afterwards, which he later complained the day after. He was taken to the workers comp Dr. who mis-diagnosed him with B-Lat Carpal Tunnel. He the went to orthopedic surgeon who diagnosed him with tendinitis.

While working on removing bucket pin on a 992 loader, dust went into employee's eyes, possibly from the exhaust from the Impact wrench while working in a confined area (employee was wearing prescription safety glasses with side shields).

Employee got finger caught between a belt and a shieve (fan). Finger was injured while employee took eyes away from hands direction causing the finger to get caught.

EE was attempting to tighten a bolt on the drag friction with a hand wrench. The wrench was struck by a drum bolt causing EE's ring finger on L. hand to become pinched between the wrench and drag friction. A fracture to the last digit of the ring finger on the L. hand was realized.

THE SWING CABLE FROM DREDGE STRUCK EE ON LEFT LEG.

OPERATOR WAS RAISING UP THE BOOM. HE GRABBED THE MASS PIPE AND THE BOOM STABILIZER CRUSHED HIS FINGERS.

EMPLOYEE WAS GRINDING A FLANGE WITH AN 11000 RPM ELECTRIC GRINDER. HE WAS PUTTING THE GRINDER DOWN WHEN IT BUMPED HIS RIGHT LEG JUST ABOVE HIS KNEE. IT TOOK SIX STITCHES TO CLOSE THE WOUND.

EE WAS GRINDING ON A SIDE WALL HOLDING GRINDER OVER HIS HEAD IN FRONT OF HIM. HE HIT THE FRAME OF UPPER DECK CAUSING GRINDER TO JUMP, TWISTING HIS ARMS CAUSING GRINDER TO STRIKE HIS WRIST, LAC ERATING IT REQUIRING STITCHES.

WHILE REMOVING A CYLINDER ON A P&H DRAG LINE A BOLT FLEW OUT AND HIT RIGHT CHEEK OF EE CAUSING LACERATION.

EE WAS CUTTING A PIECE OF 1 1/4" PIPE WITH A PORTABAND SAW. WHEN THE SAW CUT THROUGH, EE'S HAND WAS CUT BY PIPE.

EE WAS OPERATING DREDGE WHEN HE INADVERTENTLY STRUCK RIGHT ELBOW ON A LEVER CAUSING TEMPORARILY NUMBNESS TO RIGHT ARM.

DRILLING BOULDER, WENT TO MOVE THE BOOM OFF THE BOULDER, IT SLIP DOWN AND PINCHED HIS FINGER.

EMPLOYEE WAS LUBRICATING THE WALKING CAM OF THE DRAGLINE. EMPLOYEE'S HAND WAS PINCHED BETWEEN THE CAM AND FRAME.

EE WAS MOVING DRILL FROM ONE SHOT TO ANOTHER, HE STOPPED, AT THE TOP OF THE HILL FOR TRACKS TO MOVE, HE PROCEDED DOWN THE HILL ABD STARTED TO MOVE FASTER, HE ATTEMPTED TO APPLY THE BRAKES BUT DRILL WAS MOVING TOO FAST TO STOP. HE DROVE IT ONTO THE BERM TO STOP IT. DRILL STOPPED IN SLOW MOTION AND ROLLED OVER.

AFTER HOLED DRILLED, DRILLER FORGOT TOREMOVE RUBBER DUST COVER FROM ROD; LOOKED UP TO WATCH HEAD OF DRILL & SWING ROD INTO CAROUSEL. AS HE LOOKED UP THE FALLING RUBBER COVER STRUCK HIM THE FAC E KNOCKING OFF HIS SAFETY GLASSES & HARD HAT. HEWAS TAKEN BY CO. VEHICLE FOR EMERGENCY CAREA; WAS RELEASED WITH NO BROKEN BONES; NO STITCHES; NO CONCUSSION. WAS TOLD BY ATTENDING PHYSICIAN HE

WHILE USING A GRINDING WHEEL, THE WHEEL CAME OFF AND CUT EMPLOYEE ON LEFT FOREARM.

SUPERVISOR WAS HELPING ANOTHER DEPT TO DISABBEMBLE A PUMP. THE BRAKE ASSEMBLY BREAKING WERE STUCK. WHEN THE ASSEMBLY WAS LOOSENED IT WENT TO REVERSE CATCHING HIS THUMB DUE TO UNKNOWN PRESSUR E IN THE BASE OF THE PUMP.

EE WAS HIT ON HIS HARD HAT BY A ROCK WHICH WAS THROWN OUT OF THE CRUSHER.

EMPLOYEE WAS WELDING WHEN A PIECE OF SLAG FELL INTO HIS BOOT AND BURNED HIS RIGHT FOOT.

EMPLOYEE WAS CUTTING A BOLT OFF IN THE PLANT ANDA PIECE OF HOT METAL FELL INSIDE HIS RIGHT BOOT AND BURNED HIS FOOT.

DRILLER WAS PUTTING A NEW BIT ON THE ROD, THE WRENCH SPUN AROUND AND HIT HIS HAND CUTTING THE POINTER FINGER ON HIS LEFT HAND.

EE WAS WAITING TO BACK UNDER RIP RAP LOADER. HE WAS SETTING ABOUT 50 TO 100 FT AWAY FROM HAMMER BREAKER. EE HAD WINDOW DOWN ABOUT 6 INCHES ON PASSENGER SIDE. HE HAD PIECE(SMALL) ROCK FLY INTO SIDE WINDOW. IT HIM ON HIS RIGHT SIDE OF HEAD.

EE DEVELOPED BACK PAIN WHILE OPERATING BULLDOZER.

EMPLOYEE BURNED LEFT FOOT WHEN A PIECE OF HOT METAL FELL INTO HIS BOOT. HE WAS CUTTING METAL WITH A TORCH.

EE WAS USING A GRINDER TO CLEAN OFF A PIECE OF PIPE & CAUGHT HIS LEFT INDEX FINGER

EMPLOYEE WAS GUIDING FAIRLEAD INTO POSITION ON DRAGLINE AS CRANE WAS MANEUVERING IT IN GOT HUNG UP MOMENTARILY AND WHEN IT SLIPPED INTO POSITION, IT CAUGHT HIS RIGHT THUMB.

EMPLOYEE WAS CHECKING VIBRATION IN AN ELECTRICAL MOTOR (CONVEYOR DRIVE). WHEN THE V-BELT TOUCHED HIS FOREARM CAUSING A LACERATION WHICH REQUIRED FIVE STITCHES.

WORKING IN THE WELDING TO CLOSE CAUSED FLAHS BURN TO EE EYES. SAFETY SHIELD, NEEDED THE EVENT THIS HAPPEN AGAINST AS MEANS OF PREVENTION.

EMP WORKING WITH WELDERS. FAIL TO COMPLY WITH SAFETY RULES AND RECEIVED FLASH BURN FROM WELDERS,YET LIED ABOUT REPORT FOR 2 WEEKS CLAIMING INJURY CAME FROM DUST IN EYE UNTIL DR STATEMENT WAS F LASH BURN.

EE WAS LIFTING A 375 LB CRUSHER HAMMER WITH A WINCH. HE WAS GUILDING THE THE LOAD WITH BOTH HANDS. SUDDENLY THE WINCH CABLE SLIPPED ABOUT 5 INCHES CAUSING EE TO JERK FORWARD AND STRAIN HIS NEC K AND LOWER BACK.

EMPLOYEE WAS WORKING INSIDE OF A STEEL ROCK CHUTE TO DISLODGE A PIECE OF STEEL LINER PLATE WHICH WAS WEDGED IN THE CHUTE. HE CUT OFF A PIECE OF THE STEEL PLATE WITH A CUTTING TORCH AND THE 10 0 POUND PLATE FELL AGAINST HIS LEG CAUSING INJURY.

EE WAS MESSING WITH SOME WIRE ON THE MOTOR OF A HYDROSEEDER WHEN HIS HAND SLIPPED & GOT CAUGHT IN THE FAN MOTOR. CUT HIS INDEX FINGER.

THE DRILL RIG DOG CHAIN BROKE ON THE RIGHT SIDE. THIS CAUSED THE KELLY HEAD TO BECOME DISENGAGED FROM GUIDE CHANNELS. IN THE PROCESS OF TRYING TO DISLODGE THE CHAIN FROM AROUND THE SPROCKET, A GUIDE ROLLER FROM THE KELLY HEAD FELL APPROX 35FT STRIKING EMPLOYEE IN THE LEFT SHOULDER.

EMPLOYEE WAS WELDING AT THE PRIMARY JAW CRUSHER ALONG WITH TWO OTHER WELDERS. AS A RESULT, THE EMPLOYEE BELIEVES THAT WHILE REMOVING HIS HELMET TO NOTICE HIS WORK HE RECEIVED A FLASH BURN FRO M OTHER WELDERS IN THIS AREA.

EMPLOYEE SAYS THAT WHILE CLEANING A VEHICLE WHEEL WITH HIGH PRESSURE HOT WATER, THE HOT WATER SPLASHED INSIDE OF HIS RUBBER OVERBOOT, WHICH WAS NOT FASTENED AT THE TOP. T HE HOT WATER SOAKED I NTO HIS LEATHER BOOT AND CAUSED A SERIOUS BURN HE COULD GET THE BOOTS OFF.

EMPLOYEE WAS USING A HOLE SAW IN A DRILL PRESS. HE LEFT THE CHUCK KEY IN THE CHUCK. WHEN THE DRILL STARTED, THE KEY KNOCKED HIS THUMB INTO TH E SAW, CAUSING INJURY.

EMPLOYEE WAS INSIDE OF 6'X12' CHUTE UNDER PRIMARY CRUSHER WHILE CHUTE WAS BEING LIFTED INTO PLACE FOR REWELDING TO THE BASE OF THE CRUSHER. AN UNSEEN FLANGE OF STEEL AT THE TOP OF THE CHUTE R ESTRICTED THE CHUTE FROM MOVING UPWARD. THE CRANE HOOK WAS ATTACHED TO ONE SIDE OF THE CHUTE. AS THE HOOK PULLED UP. IT CAUSED A 20# PIECE OF THE STEEL CHUTE TO BREAK OFF. THE PIECE RICOCH

EMPLOYEE WAS USING A STATIONARY GRINDING WHELL TO GRIND OFF A BURR ON THE END OF A BRASS HOSE FITTING. HIS LEFT INDEX FINGER GOT CAUGHT BETWEEN TEH TOOL REST AND THE GRINDING WHEEL, RESULTING IN A DEEP ABRASION.

WHILE MOVING ABOUT INSIDE DRAGLINE HOUSE, THE EMPLOYEE LOST HIS BALANCE DUE TO THE MOTION OF THE DRAGLINE AND CAUGHT HIMSELF WITH HIS RIGHT HAND ON CENTER SHAFT. HAND WAS PINCHED BETWEEN SHAF T AND A MACHINE GUARD. GUARD PREVENTED MORE SERIOUS INJURY.

EMPLOYEE WAS CUTTING BOLTS WITH A CUTTING TORCH TO REMOVE A CONVEYOR IDLER WHEN A PIECE OF HOT METAL FELL INTO HIS LEFT EAR, RUPTURING EAR DRUM. REQUESTED TREATMENT 8/27/92.

WHILE USING PNEUMATIC IMPACT WRENCH, RETAINING PIN HOLDING SOCKET TO WRENCH SLIPPED PAST HOLDING RING, LACERATING RIGHT HAND PALM AND RIGHT MIDDLE FINGER.

RECEIVED FLASHBURN FROM NEARBY WELDING ACTIVITY.

EMPLOYEE WAS PROJECTED FORWARD INTO THE WINDSHIELD OF HIS GRADER WHEN THE GRADER BLADE CAUGHT ON A RAIL JOINT, WHICH STOPPED THE MACHINE ABRUPTLY. HE WAS OPERATING IN A STANDING POSITION W/O A RESTRAINING DEVICE. A STANDING HARNESS WAS SUBSEQUENTLY INSTALLED.

EE WAS HOLDING A STRIP OF METAL WHILE ANOTHER EMPLOYEE DRILLED A HOLE IN IT. WHEN EE APPLIED TO MUCH PRESSURE, THE 1/8" BIT BROKE AND THE DRILL SLIPPED TO ONE SIDE, WHERE THE BROKEN BIT PENETR ATED HIS LEFT FIFTH FINGER.

EMPLOYEE WAS ASSISTING WELDERS IN REPAIRING 7X20 SHAKER. REFLECTIONS OF ARC WELDING FROM WALLS OF SHAKER CAUSED FLASH BURNS TO BOTH EYES. EMPLOYEE WAS WEARING SAFETY GLASSES BUT NOT WELDING HO OD OR GOGGLES.

EMPLOYEE WAS USING AN IMPACT WRENCH TO TIGHTEN BOLTS WITH AN IMPACT SWIVEL SOCKET AN 0-RING WHICH SECURES THE LOCK PIN OF THE SOCKET TO THE WRENCH SLIPPED OFF ALLOWING THE PIN TO FALL FROM THE SOCKET THE SOCKET THEN SPUN OFF THE WRENCH STRIKING EMPLOYEE ON THE LEFT HAND CAUSING LACERATIONS