Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
EE HAD JUST COMPLETED DRILLING A HOLE & INSTALLING A ROOF BOLT. WHEN MOVED BACK TO THE INCH TRAM STATION A ROCK ABOUT 2'X 2'BY 3-6" FELL FROM BETWEEN THE ROOF BOLTS & THE RIB STRIKING HIM ON THE HEAD CAUSING THE INJURY.
THE R-BOLT OPERATOR HAD INSTALLED HIS BOLT IN THE CURTAIN BOARD, ND WAS REPOSITIONING THE MACHINE TO INSTALL A BOLT. SOMEONE CALLED WHICH DREW HIS ATTENTION AWAY AT THE SAME TIME THE MACHINE WAS MOVING. HE FAILED TO MOVE AWAY WHICH LET THEMACHINE COME IN CONTACT WITH HIS FOOT.
EE WAS ON HIS KNEES WATCHING THE MINER CABLE WHEN A PIECE OF ROCK 3 FT LONG BY 2 1/2 FT WIDE BY 2 TO 4 INCHES THICK FELL FROM THE TOP STRIKING HIM AND PUSHING HIM TO THE BOTTOM.
EMPLOYEE PUT THE DRILL STEEL AGAINST THE TOP TO BEGIN DRILLING THE HOLE. HE THEN TURNED AROUND TOWARD THE BACK OF THE MACHINE BEFORE STARTINGROTATION. A FEW SECONDS LATER HE TURNED AROUND TOWARD THE WORK AREA TO BEGIN DRILLING. AFTER HE STARTED THE ROTATION A PIECE OF ROCK 3'LONG BY 15' WIDE BY 2' THICK FELL FROM THE TOP CAUSING THE INJURY.
EMPLOYEE HAD JUST MOVED HIS DRILL BOOM TO THE INSIDE BOLT AND STARTED DRILLING THE HOLE WHEN A PIECE OF ROCK, 3'L X 4'W X 3"T FELL FROM THE INBYSECTION OF THE CUT TO THE AREA WHERE HE WAS WORK ING, STRIKING HIS LOWER LEG AREA CAUSING INJURY.
EMP WAS POSITIONING THE MACHINE TO BEGIN THE BOLTING CYCLE AND IN THE PROCESS OF DOING SO HE ATTEMPTED TO RAISE THE BOOM WITH HIS HAND ONT HE FRAME OF THE BOLTER WHICH IS A PINCH POINT. THERE WAS A SIGN ON MACHINE WHICH IDENTIFIED THIS AREAAS A POTENTIAL PINCH POINT AREA.
EE WAS WALKING ON THE CONTINOUS MINER WHEN THE GATHERING HEAD SAT DOWN ON HIS FOOT.
EE WAS PUSHING A BOLT AP TOWARD THE TOP WITH THE DRILL BOOM, WITH HIS RIGHT HAND ON THE LEVER. AND USING HIS LEFT HAND HE ATTEMPTED TO THROW A MADE UP BOLT AND PLATE FORWARD TO THE NEXT POSITI ON WHEN THE BOLT AND PLATE STRUCK THE ATRS BOUNCING BETWEEN THE BOOM THE TOP CATCHING HIS LEFT HAND AGAINST THE TOP. THE HEIGHT IN THAT PLACE WAS 38 INCHES.
EE WAS ATTEMPTING TO RAISE HIS BOOM UP FROM THE BOTTOM TO TRAM ACROSS THE SECTION WHEN HE PLACED HIS HAND IN A PINCH POINT CAUSING THE ACCIDENT.
EE WAS IN THE PROCESS OF BOLTING HTE 6 RIGHT FACE AND WHILE MOVING THE MACHINE FROM ONE BOLT TOO THE NEXT ONE IN THE PATTERN TO CONTINUE THE BOLTING CYCLE HIS KNEE SLIPPED BETWEEN THE BOTTOM DECK PAN AND THE RIB CAUSING THE INJURY.
EE IS EE AS A ROOF BOLT OPERATOR AND THE CONDITIONS WARRENT BENDING THE BOLTS BEFORE INSTALLATION AND WHILE BENDING A BOLT HE PULLED OR STRAINED A MUSCLE IN THE LEFT SIDE OF HIS BACK.
EE WAS BOLTING TOP WHEN HIS GLOVE BECAME CAUGHT ON ROTATING DRILL POT. THIS ACCIDENT DID NOT SEEM SERIOUS AT THE TIME SO THE EE DIDN'T REPORT THIS IN TIMELY MANNER. EE DID NOT REPORT THIS ACCI DENT UNTIL 12-5-95.
THE CANOPY ATTAFCHED TO THE MACHINE AFTER BEING RAISED AGAINST THE TOP BROKE THE CAP COAL LOOSE FROM THE TOP STRICKING THE VICTIM ON THE RIGHT HAND CAUSING THE INJURY
WHILE BOLTING TOP GLOVE GOT CAUGHT ON DRILL STEEL. INJURED RING FINGER ON LEFT HAND.
EMPLOYEE WAS PUTTING ROOF BOLT IN HOLE AND PUSHED WRONG LEVER. EMPLOYEE STATED THAT HE PUSHED SPIN LEVER INSTEAD OF UP PRESSURE LEVER. BOLT CAUGHT GLOVE AND PULLED WRIST (SPRAIN).
EE WAS PULLING LOOSE ROCK DOWN AS HE WAS BOLTING UP TO IT. HE WAS DRILLING HIS MIDDLE BOLT HOLE WHEN A PIECE OF ROCK FELL AND STRUCK HIM ON LOWER LEG.
PIN IN FOOT JACK BROKE ALLOWING BOOM WHICH ALSO SUPPORTS CANOPY TO MOVE DOWNWARD APPROIMATELY 10 INCHES STRIKING EE ON HEAD.
EMPLOYEE SAID HE SPRAINED LOWER BACK WHILE LIFTING DRILLPOT FOR BOLTER.
INJURED WAS OPERATING ROOF BOLTER & LOWER BOOM ON FOOT.
INJURED WAS WATCHING MINER CUT # 4RT BRR WHEN A PIECE OF ROCK OR COAL FLEW INTO HIS EYE.
INJURED WAS SITTING UP PINNER TO START PINNING WHEN A PIECE OF DRAW SLATE FELL SLIDING DOWN HIS BACK WEIGHT APPROX 40 TO 60 POUNDS MEASURING 2 1/2 FEET AWAY AND 1 1/2 FOOT WIDE AND 2 1/2 IN TH ICK ACCIDENT OCCURED IN 4 RIGHT BREAK SECOND CUT OF COAL WAS TOOK OUT OF IT.