Avísenme cuando se presente un nuevo incidente de la MSHA en Black Oak 5.
A PIECE OF DRAW ROCK DISLODGED FROM MINE ROOF STRIKING THE EMPLOYEE IN THE MOUTH & SIDE OF FACE
THE FALL OCCURRED ON THE 002 SECTION IN THE #5 ENTRY BEGGINIGN AT THE LAST OPEN X-CUT AND GOING TO THE FACE APPROX 6' IN HEIGHT X20' IN WIDTH X20' LONG.
EMPLOYEE WAS CONSTRUCTING SEALS, HIS ARMS CAME IN CONTACT WITH CEMENT, THUS CAUSING ALKALI BURNS.
STRAINED BACK LOADING MINER CABLE IN MAN TRIP AND HURT BACK.
THE FALL OCCURRED IN THE #2 ENTRY AT SPAD #1145 APPROX. 7 FEET THICK, 6/ FEET LONG, 2/ FEET WIDE.
EMPLOYEE WAS BEING TRANSPORTED IN A RAILRUNNER WHEN A PICE OF DRAW ROCK FELL THEREFORE STRIKING EMPLOYEE IN THE CHEST.
THE FALL OCCURRED IN THE #2 ENTRY (RETURN) BETWEEN THE #5 + 6 HEADDRIVES APPROX. 20 FT INBY SPAD 1348. 40' LONG X 18' WIDE X 7' HIGH.
THE EMPLOYEE WAS PUSHING THE ROOF BOLT INTO THE HOLE WITH THE DRILL HEAD, HIS GLOVE CAUGHT BETWEEN THE ROOF BOLT HEAD AND THE END OF WRENCH. WHEN HE BEGAN TO ROTATTE THE DRILL HEAD TO MIX THE GLUE, HIS HAND TWISTED AROUND THE WRENCH.
THE SHUTLE CAR OPERATOR WAS PULLING UNDERNEATH MINER BOOM, HE BUMPED THE BACK OF THE MINER THEREFORE BOUNCING THE MINER OPERATOR INTO THE MINE ROOF.
EMPL WAS CUTTING COAL WITH THE CM VIBRATION BOUNCED THE EMPL INTO THE ROOF EMPL DID NOT MISS ANY WORK UNTIL THE 24TH
THE SHUTLE CAR OPERATOR RAN OVER A SPRAY PAIN T CAN USED TO MARK CENTER LINES ON THE MINE ROOF WHEN THE CAN RUPTURED THE PAINT CONTACTED THE EMPLOYEE ON THE LEFT SIDE OF FACE AND EAR.
THE FALL OCCURRED IN THE OLD WORKS AREA OF HTE MINE NEAR THE NO 4 HEAD DRIVE IN THE RETURN APPROX 20'X100'LONGX4' THICK STARTING IN THE NO 1 ENTRY AND EXTENDING THROUGH TO THE #3 ENTRY.
THE FALL OCCURRED IN THE OLD WORKS AREA OF THE MINE.NEAR THE NO 4 HEAD DRIVE IN THE RETURN APPROX 60'X20'X7' HIGH IN THE XCUT BETWEEN THE NO 1 AND 2 ENTRIES.
EMPLOYEE WAS PUTTING OIL IN THE ROOF DRILL WHEN HE EXPERIENCED PAIN IN LOWER BACK
EMPL LIFTED OXYGEN CYLINDER IN SHOP AREA & EXPERIENCED LOWER BACK PAIN.
THE ROOF FALL OCCURRED OUTBY THE 002 SECTION APPROX. 13 XCUTS IN THE (#6 ENTRY - INTAKE) 7 XCUTS OUTBY #1295 SPAD APPROX 150 FT LONG 18 FT WIDE APPROX 7 FT THICK.
EMPLOYEE WAS LIFTING MINE RAIL AND EXPERIENCED BACK PAIN.
THE FALL OCC. 40FT INBY #1140 SPAD IN THE #1 ENTY RETURN THE FALL MEAUSRES 110 FT. LONG 3 TO 7 FT THICK 18 FT W.
THE FALL OCCURRED TWO BREAKS INBY SPAD #1175 IN THE BELT ENTRY. THE FALL MEASURED 20 FEET WIDE, 40 FEET LONG, 5 FEET THICK.
THE FALL OCCURRED ON 002-SEC 90 FT OUTBY THE FACE. 40 FT INBY SPAD #1264 IN THE #5 ENTRY APPROX. 40 FT LONG 20 FT WIDE AND 6 TO 7 FT THICK.
EMPLOYEE WAS LIFTING A BAG OF ROCK DUST AND FLE TAPIN IN LOWER BACK AREA.
EMPLOYEE WAS UNLOADING BELT BOX OUT OF SUPPLY MOTOR OUTSIDE THEREFORE STRAINING BACK.
EMPLOYEE WAS UNLOADING A BOOM FOR A ROOF DRILL OUT OF THE SCOOP BUCKET IT OVERT URNED & MASHED HIS FINGER ON RIGHT HAND
EMPLOYEE WAS RIDING IN BUCKET OF SCOOP HE BUMPED HIS LEG AGAINST THE MINE ROOF AND BRUISED RIGHT THIGHT.
EMPLOYEE WAS RE5CHING BACK FROM HIS NORMAL POSITION TO GET A ROOF BOLT AND TWISTED HIS BACK.
EMP WAS GOING T2ROUGH AIR LOCK BELTS ON TRACK WITH MANTRIP, HE PUT HIS ARM UP TOKEEP AIR BELTS FROM HITTING HIM IN THE FACE. BELTS HIT EMP ARM AND RECEIVED A STRAIN IN RT ARM
EMPLOYEE WAS HO5DING A BELT AIR LOCK CURTAIN UP ON THE MAIN LINE FOR A MOTOR TO GO THROUGH.HE CAUGHT HIS ARM IN THE BELT AS THE MOTOR WENT THROUGH THEREFORE PULLING HIS ARM BACKWARD OVER THE M OTOR. 3
EMPLOYEE WAS DI8MOUNTING THE END LOADER HE MISSED A RUNG ON THE LADDER THEREFORE FALLING TOTHE GROUND HURTING HIS BACK.
EMPLOYEE WAS PU5LING BELT TOGETHER THE CLAMP SLIPPED AND STRUCK EMPLOYEE ON THE ARM.
EMP WAS UNHOOKI3G ROCK DUSTER FROM SCOOP AND ROCK DUST GOT INTO EYES
PULLING UP MINE9 CABLE SLACK USING ROPE ROPE SLIPED & CAUGHT RT.ARM OF EMPLOYEE THE AMOUNT OF TENSION ON ROP WAS SUFFIEIENT TO PULL THE MUSCLES IN EMPLOYEES RT.SHOULDER
MANTRIP WAS PRO7EEDING THROUGH AN AIR LOCK MADE OF BELT MATERIAL.EMPLOYEE PUT FOOTUP TOWARD AIR LOCK THEREFORE PUTTING PRESSURE ON KNEE AND LEG WHEN HE CAME IN CONTACT WITH BOARD THAT BELT WAS NAILED TO. 3
INJURED EMPLOYE9 WAS PUTTING IN A PIECE OF DRILL STEEL IN PINNER HEAD.WHEN STEEL ALREADY IN HOLE ,FELL OUT ,HITTING AND CUTTING OFF THUMB.
SETTING SPADS I3SIDE MINE WHEN TWISTED BACK.
EMPLOYEE WAS US3NG A HAMMER TO KNOCK A GEAR OFF A PINION SHAFT. A PIECE OF METAL SHEARED OFF AND BECAME IMPLANTED IN HIS LEG. HE WAS BROUGHT OUT OF THE MINE AND TAKEN TO THE HOSPITAL. X-RAYS S HOWED THE METAL3TO BE ABOUT 1 1/2 IN DEEP.
EMPL MOVING PIN3ER CABLE.SAT DOWN AND THEN RAISED UP AND KNEE POPPED OUT OF PLACE.RIGHT KNEE.
TAKING COVER OF0 PANEL BOARD WRENCH SLIPPED AND HIT I.NAME IN EYE.LEFT EYE.
HE FELL ON TIMB9RS WHILE LOADING THEM AT #4 ENTRY FACE AREA.
EE WAS WORKING 5ROUND BELTLINE GOT RIGHT FOOT CAUGHT BETWEEN BELTLINE AND BOTTOM ROLLER STRUCTURE OF COND. SYSTEM.
EE WAS PINNING 7OP SWUNG CANOPY OVER TO PUT NEXT BOLT IN AND CAUGHT HIS HAND AND HUNG IT ON CANOPY LEFT HAND
EMPL PINNING TO1 PINNER HEAD FEL CATCHING RIGHT FOOT.