Avísenme cuando se presente un nuevo incidente de la MSHA en Tamaqua Breaker.
| Trimestre | Horas trabajadas | Citaciones | S&S | Por 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 3,023 | 1 | 1 | 330.8 |
| 2025 Q3 | 2,951 | 0 | 0 | 0.0 |
| 2025 Q2 | 3,469 | 1 | 0 | 288.3 |
| 2025 Q1 | 3,468 | 0 | 0 | 0.0 |
| 2024 Q4 | 3,318 | 0 | 0 | 0.0 |
| 2024 Q3 | 3,351 | 0 | 0 | 0.0 |
| 2024 Q2 | 3,402 | 0 | 0 | 0.0 |
| 2024 Q1 | 3,111 | 2 | 0 | 642.9 |
Employee was walking down to turn off plant water feed pump and slipped on ice
grinding steel and debris got in employees eye
While working in crushing plant, employee's finger was crushed between a rock and a railing
Employee slipped on ice and fell on right knee
While dismounting a ford utility truck he slipped off the step bumper and fell to the ground.
Employee was grinding steel when a piece of metal lodged in his left eye. Employee was wearing a face shield.
Employee was lifting a piece of I-Beam with right arm to put a block of wood under it.
Employee was holding angle iron between two piece of channel for x bracing while another employee welded. He was looking away from the welder but the arc was too close and caused welders flash.
He proceeded to grab the drag line trip cable, as he pulled a sharp frayed piece of cable pierced his glove and hand.
EE was grinding metal, when debris was blown into his face. He was wearing a face shield.
Shoveling coal
Employee was shoveling mud from under a conveyor belt. He twisted and popped a disc in his back.
Employee was inside a railroad car cleaning the car for loading and he slipped on ice and fell.
EE was grinding a piece of stainless steel. A piece flew into his eye from the grinding wheel.
Employee was emptying barrel used for burning trash. a piece of rust flew into his right eye. He didn't relaize it lodged there until his eye became uncomfortable, at which time he reported it to the employer.
Employees were removing drum separator from preparation plant. EE was on a ladder to reset come-a-long. The separator shifted and pinned him against a piece of steel.
Employee was grinding a plate for the vibrator in the preparation plant, something flew into his eye. It hurt a little at the time, but the pain went away, so he didn't report an injury. The pain returned a week later, he then reported the injury and went to the doctor. The doctor removed a particle from his right eye.
EMPLOYEE WAS CHANGING TEETH ON DRIVE SPROCKET OF CHAIN CONVEYOR AND PINCHED HIS THUMB.
EMPLOYEE WAS OPERATING TRUCK MOUNTED EXCAVATOR IN THE AREA OF THE CRUSHING PLANT. IT IS SUSPECTED THAT AN AIR OVER HYDRAULIC CONTROL DEVICE FAILED ON TRANSMISSION CAUSING THE VEHICLE TO GO OUT OF CONTROL AND CRASH INTO CRUSHER.
EE WAS DOING MAINTENANCE IN FINES PLANT. HE SLIPPED AND TWISTED HIS RIGHT FOOT. HE PULLED A LIGAMENT ON THE TOP OF HIS FOOT.
EE WAS GRINDING A POINT ON A CHISEL. A PIECE OF THE CHISEL GOT IN HIS EYE.
EE BENT OVER TO PICK UP TWO 55 GALLON EMPTY DRUMS, HE FELT A BURNING PAIN IN HIS LOWER BACK WHEN HE PICKED UP THE SECOND DRUM.
EMPLOYEE WAS LOOSENING STUCK CRUSHER IN PREPARATION PLANT WITH A PRY BAR. THE PRYBAR SLIPPED OUT OF THE CRUSHER GEAR AN DHIT HI IN THE FOREHEAD.
EE WAS REMOVING OIL FILTER BRACKET FROM LOADER IN AWKWARD POSITION FOR SEVERAL HOURS & AGGRAVATED PREVIOUS DISC INJURY.
EMPLOYEE WAS OPENING A GATE IN THE MORNING. HE DROPPED THE KEY,LEANED TO PICK IT UP.
EE WAS USING A SHOVEL AND POKING BAR IN BREAKER TO BREAK UP FROZEN LUMPS OF COAL.