Avísenme cuando se presente un nuevo incidente de la MSHA en Enumclaw Pit & Plant.
| Trimestre | Horas trabajadas | Citaciones | S&S | Por 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 4,746 | 0 | 0 | 0.0 |
| 2025 Q3 | 4,715 | 5 | 0 | 1060.4 |
| 2024 Q4 | 6,063 | 0 | 0 | 0.0 |
| 2024 Q3 | 1,033 | 0 | 0 | 0.0 |
| 2024 Q2 | 7,635 | 0 | 0 | 0.0 |
| 2024 Q1 | 7,167 | 6 | 0 | 837.2 |
| 2023 Q4 | 598 | 0 | 0 | 0.0 |
| 2023 Q3 | 6,582 | 1 | 0 | 151.9 |
Driving a haul truck, pinched right thumb in door frame.
Wrench hit finger between wrench and truck frame.
EE had been suffering from cough, on 1-8-20 EE was jacking up a truck when EE felt a pop in back and ribs.
While installing drive shaft into loader, drive shaft slipped and smashed middle finger on right hand.
Placing punch plate in place, plate slipped and smashed left ring finger between screen and boot. 6 stitches were received at Enumclaw ER. IE was immediately released to return to work.
Had just completed using electrical testing rod. Stood up. Went to put on hard hat with rod still in hand. Rod went under safety glasses and poked eye.
Employee was welding using Arc welder. When finished he removed his hood. He then stood up. As he was standing up he bumped the rod causing it to turn on. While it was on he received a flash burn to his eyes. Employee did not go to the doctor until 3/21/2015
Two employees were removing a screen when the injured employees crow bar slipped and hit him in the hip.
Employee pinched his finger between a cone and the wedge he was using to secure the cone still while he was turning the bolts on the cone. EMPLOYEE DID NOT REPORT THE INCIDENT UNTIL THE NEXT DAY. HE DID NOT SEEK OR RECEIVE MEDICAL TREATMENT UNTIL 5/24/2012. I FOUND OUT ABOUT THE MEDICAL TREATMENT WHEN THE DOCTOR CALLED ME DIRECTLY ON 5/25/2012.
A snap ring was coming off of a radial stacker tire. The employee was trying to repair/reset the snap ring when it popped off the tire, hitting the employee in the right ring finger. The employee needed stitches for the laceration on his finger
Strained his lower back when lifting a piece of a machine. Employee did not report this accident officially or visit to doctor. We were made aware of his trip to the doc on 9/2/11 when we received workers comp information from L&I. Employment was termed for unrelated issues on 8/17/11, employee saw doc for first time on 8/20/11. No return to work due to layoff, not injury.
Employee was hitting a part with a rubber mallet. He was holding the part with his left hand. He hammered down catching his left little finger, smashing it.
working in shop, removing spacer on piece of equipment being worked on, top rail slipped, upper piece slipped smashing third and fourth finger on left hand
Employee was working in a fuse box and did not properly shut off the power to the fuse box first. Caused an arc that caused flash burns to employees hands.
Employee was using a torch to cut a conveyor frame. When he cut away one portion of the conveyor frame the other portion where he was tied off to began to collapse and slide down a hill. As he tried to jump free, his safety harness pulled him into a conveyor cross member, striking his back and right side. He was taken to the local hospital by ambulance.
Employee was getting out of a truck, jumped to ground, acute lumbar sprain.
Employee was driving a loader and ran over pot holes that jolted him. Jolt caused lumbar strain.
Employee was unloading concrete blocks out of the back of a truck when his left thumb got squeezed between the chains used to lift the ecology blocks. Pressure caused a cut in his thumb.
One employee was lifting a steel plate with a forklift; injured employee was standing on the ground spotting and giving direction. Forklift got caught on the steel plate underneath the one being lifted. The steel plate being lifted slipped off of the forks and hit the injured employee in the chest and on the chin. Caused bruising to the ribs and slight fracture of the collarbone.
INDIVIDUAL WAS CUTTING A BELT WITH A UTILITY KNIFE.HE WAS CUTTING WITH A MOTION TOWARD HIS BODY WHEN THE KNIFE RELEASED FROM THE BELT. HE STRUCK HIS LEG WITH THE BLADE.
Employee was climbing down from a conveyor when he stepped down he twisted his knee.
A ROCK LAUNCHED FROM #1 CONE AND HIT EMPLOYEE ON THE LEFT ARM (ELBOW).
WAS RUNNING A 4" GRINDER AND SOMETHING GOT UNDER HIS SAFETY GLASSES.