¿Le interesa? Suscríbase al canal RSS de muertes por electrical — cada nueva muerte de la MSHA, entregada a su lector tan pronto como se presenta.
Miner was on first floor of "New Office" working on a ladder changing a light. Miners co-worker went to basement to retrieve another new light. Co-worker heard a thump and a bang on the ceiling. Co-worker found miner sitting slumped on the floor unresponsive. Started CPR, called 911, deployed AED but the miner could never be revived.
The employee was performing routine preventative maintenance on a transformer when EE was fatally electrocuted.
Arc flash event involving electrical equipment that resulted in burns to the employee's arms and torso as well as electrical equipment damage. The employee was injured and hospitalized after the incident but, passed away in the hospital on 08/22/2024.
Crane lifting conveyor belt off of trailer using cable rigging employee was guiding rigging crane struck overhead power line employee was electrocuted
An employee operating a Caterpillar 770 haul truck hauling material to repair the road to the stripping area. As the employee dumped the load the bed contacted overhead powerlines. The employee exited the truck to extinguish a fire. Upon returning to the truck EE reached for the handrail. When EE touched the truck, EE was electrocuted.
Investigation is still under way and an autopsy is being performed to determine cause. *Per the prelim: Two contractors were electrocuted when a 14,400-volt overhead power line came in contact with their off-road dump trucks, and the contractors exited their trucks and contacted the ground.
Investigation is still ongoing, and an autopsy is being performed to determine the cause. *Per the prelim: Two contractors were electrocuted when a 14,400-volt overhead power line came in contact with their off-road dump trucks, and the contractors exited their trucks and contacted the ground.
An examiner was found unresponsive in an underground sump. As of this time the exact cause of the employee's death is still undetermined.
On 09/01/2022 at approximately 4:40 p.m. at 32 brk on 2 Belt track, employee came into contact with a 480 volt roof bolter cable and was fatally injured.
Contributing Factors: (1)Energized equipment. (2)EE failure to follow company LO/TO procedures. (3)Outer wire jacket showed signs of heating & cooling. (4)EE grabbed the live "C" phase wire.
Employee was working in a de-energized 4160 volt GFCI controller in an attempt to reverse the polarity of the wires when it somehow became energized.
EE was attempting to identify the problems with the scrubber motor on the JM 6911 continuous miner on the number one section in the number one entry when EE came in contact with electricity. The employee was brought to the surface and transported by ambulance to a Hospital where EE later passed away from the injury sustained from the incident.
A contractor died at the operation underground. The cause of death is unknown at the time of this report. MSHA issued a 103(k) order on the area. The information in this report is all we have at this time.
EE was working to replace a high voltage starter for the slope belt and was in the process of adjusting the mechanical linkage connected to the switch when EE came in contact with electricity. EE was transported via ambulance to CAMC Memorial where EE passed away from the injuries sustained from the incident.
Employee was electrocuted by transformer power.
Temporary contracted employee contacted the 12500 volt overhead power line with an irrigation pipe
Employee went to prime the diaphragm pump located outside the stripping machine building, adjacent to the hydraulic room. Eight minutes pass where EE is unaccounted for prior to being found unresponsive, kneeling in liquid, face against the stainless steel flange of the tank house return HDPE line.
The employee was working on a Fletcher roof bolter. He had the panel board off trouble shooting inside the electrical components of the machine. He apparently came in contact with electricity. The investigation is not complete at this time.
Employee pulled aluminum boat over three electric conductors in dredge pond. A patch on the bottom of the boat cut into one conductor and electrocuted the employee. The employee died as a result of the accident.
Employee was working near an energized Soft Start Component. Started convulsing or having a seizure. Possible electrocution. Still unknown.