HARDING STREET QUARRY-SURFACE Metal/Non-Metal

Opening a sliding fence gate. Pinched right pinky in roller guide. Required an X-ray and stitches. Hairline fracture at base of pinky.

Windy and gusting weather conditions blew dust and debris into employee left eye

EE1 arrived at Hanson Harding Street, checked out a 775 haul truck and drove it over to the restroom. EE2 noticed EE1 slumped over steering wheel. EE3 stopped to check on EE1 and EE1 was unresponsive and EE3 called 911. Ambulance crew gave EE1 medicine to revive EE1, then took EE1 to the Hospital.

Employee hit right elbow causing contusion on metal frame while using hammer to dislodge built up material from screen.

Employee was lifting liner plate into chute above crusher, when wind caught plate turning it into metal guarding causing dust and dirt to come down onto EE and into EE's eye.

Employee was trying to knock loose stuck rock from a catwalk with a hammer when loose rock came back and hit EE in mouth damaging EE's left front tooth.

Employee was airing up a tire on a 40 ton haul truck when the tire blew. EE was taken to local hospital and received treatment for two fractures on the neck and two on the back and one on EE's knuckle.

Employee stated they slipped and scraped right lower leg on track of Cat 330 excavator.

Crane was holding the lock post cylinder 8"-10" above the platform as the emp was kneeling beside it EE was hitting the lock post cylinder rod trying to extend it out when the snap ring holding the top cap in place came out and allowed the cylinder body to come loose, hit the platform and fall onto the emp knee.

Emp was operating haul truck hauling shot rock to the primary crusher. While being loaded, the bucket of the loader contacted the truck bed and jerked the truck. The emp complained of back pain and told the super about incident but refused med attn at that time. On 9/21 the emp told the super was in a great deal of pain and needed to seek med attn for back pain.

Torque wrench was being used in a tight space making it difficult to remove from bolt.

Employee was doing maintenance on plant feeder. Debris blew into left eye.

Employee was changing oil in screen 2 at the stone plant. When he had completed the job he was attempting to lift the 5 gallon pail of used oil out of the back of the screen. He attempted to lift the pail while also turning to the side. During this motion, he felt a pinching sensation in his lower abdomen resulting in a groin strain.

While re-installing the belly pan the pry bar slipped the belly pan came open and hit his right eye.

Employee hit finger with a hammer.

While cleaning up tooling employee strained back.

Employee strained Left Arm while using sledge hammer

Bent over cutting up old conveyor truss with a cutting torch and a piece of rust popped up and went behind employee's cutting shield and safety glasses getting into his right eye, treated with eye drops.

Employee was manually removing material from C3A Conveyor beltline. Employee performed job and after job was finished said that his back was tight. Employee said Monday at work he had no complaints and back felt better. Monday evening approx. 6:30pm his back started hurting badly. He reported the injury to his supervisor on Tuesday August 5, 2008 in the morning.

EE twisted her knee while climbing onto a haul truck.

Employee was grinding a bore hole on a standard crusher mainframe. The employee put the grinder down, picked up the polisher, looked up to not hit his head on the mainframe and steel fell off his grinding shield. The steel fragments went behind safety glasses and into employees right eye.

Pulling electrical cable with pick-up truck for relocation, employee's right ankle became entangled, causing compression fracture to right ankle.

EE was pushing pile of dirt with the D8T dozer, he had his coat hanging in the back of dozer which created a blind spot, he went into reverse and backed up about 10 feet, when he back up he didn't see other ee coming in the A40D hual truck with a load of dirt to unload, he backed up into the haul truck, which caused the tracks of the dozer, to collide with front end truck.

EE utilizing utility knife, was trimming rubber skirting material to align with receiving hopper; location of accident was C-12 Stone Plant.

Employee was digging out the primary crusher. A rock rolled down from the feeder and struck the employee in the left lower back.

Employee utilizing Oxy Thermal cutting torch to remove wear parts from impact crusher; while cutting, a piece of slag landed on the employee's left knee and burned through his pants & subsequently burned the outside of left knee. Slag traveled down pant leg and burned top of left foot.

Employee changing ball valve on grease line(pressure side). Employee did not release/purge pressure from system prior to attempting to change ball valve. Employee received a high pressure injection injury(grease).

Returning from dumping a load of rock, he hit a pot hole in the road, which jarred him in the truck & caused him to strain his back.

He hit a low area in the road which caused him to bounce around in the haul truck and hit his head and elbow on driver's side window.

Employee was grinding a piece of steel plate and something got into his right eye. Medication for eye was prescription.

Employee was bouncing in truck while driving and felt pain in right knee. *Transferred to another job assignment.

Employee was pulling steel out of hand box when it slipped catching hand.

EMPLOYEE FELL COMING DOWN STAIRS. TWISTED/SPRAINED HIS LEFT KNEE.

EMPLOYEE STEPPED DOWN FROM HAUL TRUCK ONTO A ROCK.

Employee was unraveling hose when the clamp cut his finger.

Employee was turning the steering wheel of a 773 truck when he felt a sharp pain in right elbow.

Employee was burned by a dropped cutting torch.

EE STRUCK RIGHT HAND WITH SLEDGE HAMMER WHILE PERFORMING MAINTENANCE ON A SPRAY BAR

EE WAS CUTTING RUBBER WITH UTILITY KNIFE. KNIFE SLIPPED, CUTTING EE'S LEFT FOREARM. SUTURES REQUIRED.

BEFORE SHIFT STARTED, EE WAS THROWING UP AS HE WALKED AWAY FROM JOB TRAILER. HE SLUMPED OVER, UNABLE TO RESPOND VERBALLY TO COWORKER. ONE SIDE OF HIS FACE WAS SAGGING. TAKEN TO HOSPITAL - ADMITTED FOR MILD STROKE.

While driving to get reloaded with sand he hit a pot hole, which caused him to bounce around causing him to strain his lower neck and upper back.

EE WAS HELPING INSTALL BELT FLAP WHEN CUTTER SLIPPED CAUSING CUT TO LEFT FINGER.

EE WAS CUTTING BELTING WITH KNIFE WHEN THE KNIFE SLIPPED CUTTING LEG. SUTURES.

EMPLOYEE WAS DIGGING OUT CRUSHER WHEN A ROCK FELL ON HIS FINGER. POSITIVE X-RAY AND RIGID SPLINT.

USING A PORT-A-POWER & AN ALL THREAD BOLT, OWNED BY ALLBRIGHT WELDING. ALLBRIGHT WAS INTALLING BUSHINGS ON A CAT 350 DIPPER STICK. THE ALL THREAD BOLT BROKE UNDER THE LOAD & THE END PIECE & NU T OF THE ALL THREAD BOLT STRUCK EE IN HIS UPPER RIGHT CHEST, WHILE HE WAS ASSISTING ALLBRIGHT, BY TAPPING BUSHINGS WITH A HAMMER.

EMPLOYEE WAS TAKING A CHAIN OFF A PUMP. THE PUMP SHIFTED CAUSING THE CHAIN HOOK TO CUT THROUGH FINGER.

EMPLOYEE WAS TIGHTENING BOLTS ON BASE PLANT CRUSSHER. THE WRENCH SLIPPED CAUSING STRAIN TO LEFT THUMB & HAND. ***RIGID SPLINT.

EE WAS DRIVING HAUL TRUCK, STRUCK A HOLE AT THE BASE OF RAMP CAUSING PAIN IN LOWER BACK. RESTRICTED DUTIES, TRANSFERRED TO ANOTHER JOB ASSIGNMENT.

EMPLOYEE WAS ON A LADDER TIGHTENING BOLTS ON AN OVERHEAD BEAM. THE LADDER SLID OUT FROM UNDER HIM CAUSING HIM TO FALL ON HIS BACK.

EMPLOYEE WAS CLOSING CRUSHER DOOR WHEN IT FELL CAUSING LEFT ARM TO OVER EXTEND.

EE WAS GOING DOWN AN INCLINE ROAD TO RELOAD WITH SHELL, THE INCLINE WAS WET, HER TRUCK STARTED TO SLIDE SIDEWAYS, SHE WAS GOING SLOW TO TRY TO CONTROL THE TRUCK, THE OPERATOR IN THE HAUL TRUCK BEHIND HER ENCOUNTERED THE WET ROAD ALSO AND SLID INTO HER TRUCK.

EMPLOYEE WAS CARRYING A HYDRAULIC CYLINDER, WHENIT SLIPPED CAUSING A CUT ON HIS RIGHT HAND FINGER.

EE WAS RUNNING HAUL TRUCK, THE TRUCK SLAMMED UP AND DOWN WHICH CAUSER HER TO SPRAIN HER BACK.

EMPLOYEE REACHED FOR BELT LAYING ON THE FLOOR UNDER CRUSHER GUARD WHILE CRUSHER WAS RUNNING.

EMPLOYEE STATED THAT HE BENT OVER TO PICK UP A ROCK FROM THE ROAD. EMPLOYEE DIDN'T REPORT THIS UNTIL DAYS LATER. NOT REPORTABLE UNTIL 9/11/01 (SURGERY).

EE WAS GOING DOWN A SMALL SAND RAMP TO RELOAD. LOST CONTROL OF HIS TRUCK WHICH CAUSED HIS TRUCKTO BOUNCE HARD AND HIGH. THE HARD BOUNCE CAUSED HIM TO STRAIN HIS BACK, NECK AND SHOULDER.

EE WAS DOING MAINTENANCE AT PLANT WHEN HE STRAINED HIS RIGHT SHOULDER. STRAIN OCCURRED ON 5-8-01 BUT WAS NOT REPORTABLE UNTIL HE RECEIVED INJECTION ON 6-1-2001.

EMPLOYEE PICKED UP A ROCK & SAID HE FELT NAUSEATED, BUT IT WENT AWAY. ***BECAME REPORTABLE W/SURGERY ON 12/10/01.

EMPLOYEE WAS WALKING TO THE PROMARY CRUSHER WHEN HE STEPPED DOWN AND HIS ANKLE POPPED.

EE WAS REMOVING A BOLT FROM A MOTOR WHEN HIS FINGER WAS PINCHED BETWEEN THE IMPACT AND THE MOTOR.

EE WAS WORKING ON PRIMARY ROTOR WHEN FINGERS GOT BETWEEN BELT AND BELT SHIVES.

EE WAS SPLICING BELT AND FELT IRRITATION IN RT EYE.

EMPLOYEE HAD ADJUSTED CHUTES AT THE STONE PLANT AND WAS WALKING DOWN THE STAIRS WHEN HE SLIPPED AND INJURED HIS THUMB CATCHING HIMSELF. EMPLOYEEIS IN A SPLINT.

EE WAS DOING CLEAN-UP WHEN HE TRIPPED OVER HOSE CAUSING HIM TO TRIP.

EE WAS ON CATWALK OF CONVEYOR 23. EE UNHOOKED THE CHAIN, TAKE-UP FELL AND DRAGGED EE OFF THE CATWALK CAUSING HIM TO LAND ON BOTTOM IDLER.

EE WAS DRIVING A PIN ON THE BACKHOE TRACK AND A PIECE OF METAL FROM THE PIN WENT INTO HIS SKIN. FOREIGN OBJECT REMOVAL FROM A DOCTOR.

EE WAS CUTTING OLD CONVEYOR BELT WHEN THE BLADE CAME OUT OF THE UTILITY KNIFE CAUSING HIM TO RUN HIS FINGER OVER THE BLADE.

EE WAS WALKING DOWN STEPS, LOST HIS FOOTING & CAUGHT RIGHT INDEX FINGER ON HANDRAIL STITCHES

EMPLOYEE LOST BALANCE WHILE GETTING OUT OF LUBE TRUCK REACHED FOR DOOR AND RIGHT HAND WENT THROUGH WINDOW.

EE STEPPED DOWN OFF LOADER & TWISTED RT KNEE.

EE WAS HELPING TO MOVE A DESK AND INJURED HIS WRIST AS HE WAS SITTING THE DESK DOWN.

EE WAS USING A SPRAY HOSE WHEN HE SLIPPED AND HIT HIS ELBOW ON ASTEEL BEAM.

EE WAS SERVICING A DOZER WHEN A LINE CUT LOOSE SPRAYING TRANSMISSION FLUID INTO HIS FACE. FLUID GOT BEHIND HIS SAFETY GLASSES AND INTO HIS EYES.

EE WAS SPRAYING WITH A HOSE AND HIT HER ELBOW ON CONCRETE WALL.

EE WAS CLIMBING DOWN THE LADDER OF HIS PIT TRUCK WHEN HE MISSED THE STEP CAUSING HIM TO FALL & INJURE HIS LEFT ELBOW & HIP.

EMPLOYEE HAD A MILD HEART ATTACK.

EE WAS TIGHTENING BOLTS IN CRUSHER WITH A RATCHET WHEN THE RATCHET SLIPPED CAUSING EE TO SMASH HIS FINGER.

EMPLOYEE WAS ENTERING HIS HAUL TRUCK WHEN HE STEPPED UP ON LADDER HIS FOOT SLIPPED CAUSING HIM TO FALL AND STRAIN HIS INGUINAL.

EMPLOYEE WAS STEPPING DOWN FROM LAST STEP OF HIS LOADER WHEN HE FELT A SHARP PAIN IN HIS LOWER BACK.

EMPLOYEE WAS WALKIGN ACROSS THE TIR EOF LOADER TO GET TOT HE BACK OF LOADER WHNE HE SLIPPED AND FELL.

EMP WAS CLIMBING LADDER. LADDER SLIPPED CAUSING EMP TO FALL AND SPRAIN RIGHT ANKLE.

EMPLOYEE ALLDGED STRAINED LOWER LEG WHILE DRIVING LOADER. SEAT WAS STIFF.

EMPLOYEE WAS CLIMBING UP ON HER TRUCK AFTER SHE HAD WASHED HER HANDS BUT HAD NOT COMPLETELY DRIED THEM. SHE SLIPPED INJURING HER KNEE.

EMPLOYEE WAS WALKING ON DEISTER FLOOR, SLIPPED AND TWISTED HIS LEG.

EMP LOST BALANCE ON ROCK AND JAMMED HAND INTO LOADER.

EMP WAS WALKING UNDER A CONVEYOR BELT AND HIT HEAD. LIGHT DUTY.

EE WAS OPENING A NEW WINDOW THAT WAS IN A BIND AND HURT HER HAND.

EE WAS USING A CUTTING TORCH WHEN THE TIP GOT CAUGHT ON HIS SLEEVE & BURNED HIS WRIST. SECOND DEGREE BURN.

EE STATED THAT HE HAD BEEN HELPPING TO LIFT A TRANSFORMER & PULLED A MUSCLE. EE REFUSED TREATMENT UNTIL 2/19/97.

TORN ROTATOR CUFF, EXACT CAUSE NOT KNOWN. CONFIRMED WORK RELATED BY CO. PHYSICIAN. SURGERY SCHEDULED FOR JANUARY 21, 1997.

EE WAS GOING UP THE LADDER OF HIS PIT TRUCK WHEN HE FELT A PAIN IN HIS BACK.

EMP WAS GRINDING METAL WHEN A PIECE OF IT HIT GLASSES AND BOUNCED INTO HIS EYE.

EE WAS SPLICING BELT WHEN HE SLIPPED AND HIT HIMSELF IN HIS LEFT TESTICLE.

EE STATED THAT HE WAS WORKING ON THE BOLTER WHEN SOMETHING FLEW IN HIS EYE.

EMPLOYEE WAS TIGHTENING A NUT WITH A RATCHET. THE SOCKET SLIPPED AND THE RATCHET HIT HIM IN THE LEG.

EE WAS REMOVING ROLLERS AND REINJURED LOWER BACK.

EMPLOYEE WAS HITTING HAMMER CAP WHEN HE FELL ANDLANDED ON THE HAMMER.

EMPLOYEE WAS WALKING UP A HILL TO CHECK FLOOD GATES AND FELL.

EMPLOYEE WAS TIGHTENING A NUT WHEN THE WRENCH SLIPPED AND HIT HIS FINGERS.

EMPLOYEE WAS PUTTING A FLOOR PLATE IN PLACE, LEG GOT CAUGHT BETWEEN FLOOR PLAT AND I-BEAM.

EMPLOYEE WAS TIGHTENING A BOLT.

EMPLOYEE WAS HOLDING ONTO A ROPE TO KEEP FROM BRAKING. THE CHUTE CAME LOOSE AND PULLED HIS ARM.

EE WAS REMOVING DRIVE SHAFT WHEN HIS HAND SLIPPED ON GREASE. HIS HAND WENT IN BETWEEN THE DRIVE SHAFT AND DIFFERENTIAL YOKE. THE DRIVE SHAFT FELL AND SMASHED HIS THUMB.

EE WAS GETTING HOUR METER READING FROM EXCAVATOR WHEN HIS PANT LEG GOT CAUGHT. HE REACHED UP TOE GRABE HANDRAIL AND HIT HIS HAND.

EMPLOYEE WAS CLIMBING LADDER ON 988, SLIPPED OFF CAUSING PAIN TO LOWER BACK.

EE WAS WORKING ON A CRUSHER WHEN HE SLIPPED AND STRAINED HIS LEFT SHOULDER.

EE WAS PULLING WATER HOSE UP THE SHORTHEAD DECK. THE HOSE WAS STUCK IN MUD.

EMPLOYEE LIFTED SCREEN CLOTH AND PULLED HIS BACK GOING UP AND DOWN THE STAIRS.

EE WAS REMOVING LINER FROM CHUTE PLATE WHEN IT FELL BACK ON HIS HAND.

EMPLOYEE WAS CLIMBING INTO A BOBCAT, SLID AND FELL. HIS BODY WEIGHT WENT ONTO THE SIDE OF HIS RIGHT HAND.

EMPLOYEE WAS WALKING TO THE MINE TRAILER AND SLIPPED ON ICE.

EMPLOYEE WAS WORKING IWTH FLOOR BEAMS & HIS FINGER WAS CAUGHT BETWEEN TWO OF THEM.

EMPLOYEE WAS DRIVING FROM THE PLANT TO THE SHOP WHEN THE EMPLOYEE, FOR NO APPARENT REASON, BECAME UNCONCIOUS. THE VEHICLE HIT A STOCKPILE & A CONCRETE POST.

EMPLOYEE WAS CUTTING THE TOP OFF OF A 1 GAL JUG WHEN THE KNIFE SLIPED & CUT THE RT THUMB

EMPLOYEE WAS TURNIGN A WRENCH TO BREAK LOOSE A NUT AND SLIPPED OFF THE WRENCH.

EMPLOYEE WAS INSTALLLING A LINERPLATE IN A CHUTE & STRAINED HIS BACK

EMPLOYEE WAS CUTTING AROPE FROMT HE DRAGLINE CABLE. THE KNIFE SLIPPED CUTTING HIS LEFT THUMB.

EMPLOYEE WAS CLEANING CONVEYOR BELT, HIS FOOT SLIPPED ON LOSOE ROCK STRAINING GROIN.

EMPLOYEE WALKED UNDER CONVEYOR & RAISED UP TO SOON. HE JAMMED HIS HEAD ON FRAME.

EMPLOYEE WAS KICKING ROCKS OFF THE UPPER 6 X 16 SHAKER FLOOR WITH HIS RIGHT FOOT WHEN HE PULLED HIS RIGHT UPPER THIGH MUSCLE.

EMPLOYEE WAS ATTEMTPING TO REMOVE A BEARING HOUSING FOR BEARING REMOVAL EMPLOYEE WAS STRIKING THE BEARING WITH A HAMMER & A PIECE OF THE HOUSING FLEW OFF & STRUCK HIS LEFT FIFTH FINGER

EMPOLOYEE WAS SHOVELING AT PRIMARY THE WIND BLEW SOMETHING INTO HIS EYE

EE WAS WALKING DOWN A DECLINED WLAKWAY AND SLIPPED LANDING CATCHING HIMSELF WITH HIS LEFT HAND.

EMPLOYEE WAS SHOVELING UNDER #2 CONVEYOR. WHEN SHOVELING SAND, SHOVEL STRUCK TIMBERS THAT PORTABLE LEGS SIT ON. IT IN TURN JARRED SHOULDER AND BACK.

EMPLOYEE WAS WORKING INSIDE OF CRANE WHEN HIS RIGHT EYE STARTED TO BURN. EMPLOYEE THEN TOOK HIS GLASSES OFF AND RUBBED HIS EYE. HE THEN WENT TO THE SHOP AND FLUSHED HIS EYE. WHEN THIS DID NOT WORK, HE WENT TO THE CLINIC.

THISL ACCIDENT WASN'T REPORTABLE WHEN IT OCCURRED, HOWEVER THERE HAS NOW BEEN LOST TIEM DUE TO THE ACCIDENT. IN JUNE EMPLOYEE SAID THE FRAME WHICH THE TRUCK SEAT SITS ON NEEDED TO BE REPAIRED BECAUSE IT ROCKED WHILEHE WAS DRIVING AND CAUSED HIM TO HAVE A MUSCLE STRAIN.

EMPL GOING DOWN INCLINE TOWARD TUNNEL ON WET SNOW.LOST FOOTING AND FELL AGAINST CONVEYOR SYSTEM ON BACK.

EE WAS STANDING ON HANDRAIL TO ASSIST IN MAKING A CUT IN SOME PLATE. HE STARTED TO GET DOWN AND HIS FOOT SLIPPED CAUSING HIS SHOULDER TO TWIST.

EMPLOYEE WAS USING HIS RIGHT HAND FOR SUPPORT WHILE USING HIS LEFT HAND TO KNOCK MATERIAL OFF CONVEYOR PAN. HE HIT HIS RIGHT THUMB WITH THE HAMMER IN HIS LEFT HAND.

EMPL CLEANING BASEMENT OF PRIMARY WITH SHOVEL.WIND CAUGHT MATERIAL AND BLEW IT BACK INTO FACE.MATERIAL GOT IN RIGHT EYE AROUND SAFETY GLASSES.

EE WAS GRINDING ON AN EXHAUST PIPE. HE HAD HIS GLASSES ON, BUT STILL HAD METAL INHIS HAIR, BROWS AND SHIRT. HE WENT HOME TO SHOWER BUT HIS LEFT EYE STILL FELT SCRATCHY.

EMPLOYEE WAS AT STONE PLANT USING WATER HOSE TO DO HOUSE-KEEPING & CLEAN-UP HE TURNED & WALKED INTO A PIPE CUTTING THE BRIDGE OF HIS NOSE

EMPLOYEE WAS WALKING AROUND FRONT OF CONTROL POWER TO TURN PLANT OFF. EMPLOYEE SLIPPED ON WET MATERIAL IN FRONT OF POWER UNIT. WHEN HE FELL HE GRABBED UNIT WITH HIS LEFT HAND, CUTTING HIS MIDD LE FINGER.

BRUSHING OFF RUST WITH A WIRE BRUSH. A FOREIGN OBJECT WENT INTO HIS EYE. (RIGHT EYE)

CLEANING PAN OF BELT WHIEL BELT STILL MOVING GLOVED RIGHT HAND GOT PINCHED BETWEEN ROLLER AND BELT DRAGGING HIS HAND BETWEEN BOTH

CLEANING UP CONVEY IN PAN STANDING IN FRONT OF CONV DRIPPING AWAY MATERIAL WITH SHOVEL BECAME EWEDGED BETWEEN MATERAIL AND BELT CAUSING SHOVEL WHILE STILL IN HAND TO RIDE UP BETWEEN BELT AND AN IDLER CAUGHT L HAND INJ TO L THUMB

EMPLOYEE TURNED TO STEP OFF OF THE DOZER, HE SLIPPED OFF OF THE PUSH ARM AND FELL TO THE GROUND.

EMPLOYEE WAS WELDING ON PRIMARY DUMP HOPPER WHEN HOT SLAGE ROLLED INTO HIS BOOT, AND AT THE SAME TIME, EMPLOYEE RECEIVED FLASH BURNS FROM ANOTHER EMPLOYEE WELDING. THE FALSH BURNS WERE NOT DI SCOVERED UNTIL 3:00 A.M. ON 4-13-90. EMPLOYEE RECEIVED BURNES ON LEFT FOOT, ADN FLASH BURNS TO HIS EYES.

EMPLOYEE BENT OVER TO PICK UP MOTOR BASE. FELT SOMETHING PULL IN THE BACK OF NECK.

INSTALLING IDLER ON CONVY 25.

RAISED UP JABBED RIBS ON ANGLE IRON CONV 20

EMPLOYEE WAS LOWERING ROLLER TO GROUND.

EMPLOYEE WAS CHANGING V-BELTS TO LOCATE SIZE & GOT HIS FINGERS CAUGHT BETWEEN V-BELTS & THE SHEAVE

EMPLOYEE WAS PULLING TORCHES UP INCLINE TO TUNNEL. HE LOST HIS FOOTING AND STRAINED LOWER BACK TRYING TO HOLD TORCHES.

ROCK CAME OUT OF THE MOUTH OF CRUSHER & LANDED ON HANDRAIL WHERE EMPLOYEE HAD HIS HAND.

EMPLOYEE WAS INSTALLING A DRIVE SHAFT ON AN R-35 HAUL TRUCK WHEN DRIVE SHAFT SLID DOWN & CAUGHT HIS FINGER BETWEEN YOKE & THE SHAFT

EMPLOYEE WAS CLEANING FLOORS WITH A SHOVEL AROUND FEEDER AND CRUSHER AREA. AN EXHAUST FAN USED TO REMOVE FUMES FROM THE WELDING AREA BLEW SLAG INTO EMPLOYEE S RIGHT EYE.

EMPLOYEE WAS LOADING HAUL TRUCKS THAT WERE STOCK PILING. BACKED UNDER CONVEYOR AS THEY REVERSED IT.

EMPLOYEE WAS CL9ANING OUT A RETURN ROLLER. BELT CAUGHT HIS LOOSE CLOTHING AND PULLED HIS HAND OVER TOP OF OUTSIDE ROLLER.

EMPLOYEE WAS MO5ING EUCLID TRUCK FROM ONE SIDE OF THE SHOP BUILDING TO THE OTHER

EMPLOYEE STAES 2E WAS CLEANING ROCKS FROM FEEDER & INJURED HIS LOWER BACK

EMP WAS DRIVING3A TRUCK AND DUST FLEW INTO HIS LEFT EYE

EMPLOYEE WAS RE5CHING DOWN THE CABLE TO PULL ON IT AND STARY WIRE WENT INTO THE PALM OF HIS HAND.

EMPLOYEE BENT O5ER TO PICK UP A OLD SCREEN STRAINED STOMACH MUSCLE.

EMPLOYEE WAS US3NG A PRY BAR TO LOOSEN A HAMMER AT THE PRIMARY CRUSHER WHEN IT SLIPPED AND HIS HAND WAS CAUGHT IN BETWEEN

EMPLOYEE WAS HE5PING OPERATOR REMOVE LARGE PIECE OF STONE FROM A 5 1/2 INCH PRIMARY CRUSHER GOT H IS FINGER CAUGHT.

EMPLOYEE WAS LI0TING LOADER BUCKET TOOTH AND ADAPTER OUT OF LOADER BUCKET.

EMP WAS GETTING3OUT OF THE TUB OF THE MARION 7400 DRAGLINE

EMPL OPERATING 8OZER WEEDS BLEW FROM ENGINE FAN IN HIS FACE.PARTICLES OF WEEDS WENT INTO HIS EYE.

EMPLOYEE WAS RE4OVING LEAF SPRING BOLTS FROM REAR END OF DUMP TRUCK USING BREAKER BAR & SOCKET HIS FINGER BECAME JAMMED BETWEEN TRUCK FRAME & BAR-INJURY TO RT INDEX FINGER

WHILE EXITING F9OM CAB OF PIT TRUCK HE WAS OPERATING HIT KNEE OF RIGHT LEG ON THE DOOR FRAME.

EE ALLEGES POSS3BLE EXPOSURE TO TOXIC FUMES.

EMPLOYEE WAS USING A HAMMER TO STRIKE BUCKET PIN ON 175B MICHIGAN LOADER WHEN A METAL SLIVER ENTERED EMPLOYEES RIGHT EYE.

EMP SPRAINED ANKLE WHEN HE STEPPED OFF THE PATION AT THE 522 SHOP WHILE WALKING TO HIS TRUCK

CAUSED HYDRAULIC JACK TO BLOW UP, THROWING STEEL WEDGE AT EMPLOYEE.

EMP WAS HELPING TO LOAD STEEL BEAMS OFF GROUND ONTO TRUCK METAL WAS FROZEN TO THE GROUND WHEN HE SLIPPED ON ICE

EMPLOYEE SLIPPED ON ICE AND FELL WHILE GREASING HEAD PULLY OF CONVEYOR EMPLOYEE BROKE ANKLE