Mesabi Metallics Company LLC Metal/Non-Metal

EE was putting a 3/8" x 4' x 2' piece of steel into the scrap bin when it fell and partially landed on the outside of their right foot.

EE and a partner were moving 60-80-pound return rollers from the staging area to a cart for transport to the work area. While lowering one roller onto the cart, EE's partner set down their end first which caused the roller to shift and slip from EE's hands. EE's gloved left hand became caught between the return roller and rack resulting in pain and swelling to left index finger.

EE arrived onsite past check in shack, hit pothole which caused tire to blow. While changing tire, jack slipped out causing the vehicle to fall, pinching a hand between tire and fender.

Tweaked while moving an 18" piece of duct on the ground.

EE was coming down stairs which were wet from rain. EE stated EE headed down the stairs and the handrail was wet, EE stepped wrong and rolled EE's ankle. This caused pain to the outside of EE's ankle and to the top of the foot.

EE was in the process of cleaning the shaft of the fan. Crew recognized the hazards of the insulation pins prior to starting work and had bent them down to decrease the potential of sticking themselves. During the cleaning of the fan shaft EE bent elbow to move and caught back of arm/elbow with the pin causing sharp point to impale the tip into skin. Caused a small puncture wound.

kneeling while wiring a vfd, this building has concert floor, dry and level.

Welding when a piece of slag fell and burned through EE's jeans.

EE was walking on grating that had been installed in slurry bridge. Crew was in the process of lifting the slurry tank agitator gearbox to do a test fit for the millwrights. Piece was overhead, EE was watching the piece and not watching where they were in relation to the open hole. EE stepped off the grating, there is a clip on the beam that EE struck shin on causing cut about 3".

Employee was cleaning out the thickener tanks on the south end. While cleaning, employee slipped on mud. Employee fell and twisted left knee.

Employee lost control of grinder and cut EE's leg.

EE and crew were turning a floor brace using a sleever bar in one of the bolt holes. Brace was on flat side. EE standing on E side of the N/S aligned brace pulling on the bar toward EE. In the line of fire when piece reached tipping point where crew needed it for rigging to put in place. Piece reached tipping point, EE lost footing. The sleever bar struck EE's leg causing cut.

EE and partner were setting up a jig to assist in fit up of the ring to the duct work. EE was holding the piece low to assist in getting the jig welded to the duct. EE's partner stuck EE's weld rod to tack up the piece and rod got stuck. When EE went to remove the rod, the piece fell and landed on EE's pinky fingertip which caused a laceration. EE did have gloves on.

While moving a skirt that goes on to a conveyor, weighing approx. 150-200 pounds, while on a skate it slid off and pinched left thumb. EE was rushing and did not wait for other staff to secure it before moving it.

EE was assisting spreading a telehandler forks, while they tilted mast down to facilitate tine adjustment, the right tine was moved, after EE began sliding the L tine outward. During this process, the R tine slid back unexpectedly. EE attempted to reposition the R tine w/EE's gloved L hand, EE L middle finger got pinched between tine and mast's lower bar. Skin tear on L finger.

Employee was using an oxygen/acetylene torch to heat and shape rebar material. The worker inadvertently tripped over the torch hose, which resulted in a loss of balance. As a result of the trip, the worker unintentionally made contact with the active torch flame, causing a burn to the left wrist, just above the cuff of the glove.

Cable pull, picking up cable for refeeding into vault. Cable was being fed into vault and pulled out by hand to get it prepped for next pull into building from this vault.

Employee was holding a bull pin with their right/dominant hand and missed, hitting it with a hammer with their left hand and instead hit their right hand with the hammer.

EE first said EE had been experiencing soreness for sometime but no specific event occurred, then EE changed EE's story and now claims EE lost EE's footing a bit while climbing a column, and noticed soreness later that day. However, EE failed to inform anyone until Sunday, March 29th.

EE hit EE's left index finger with a hammer while aligning a piece of steel.

EE was positioned beneath the outlet duct assisting coworker with placement of a stiffener ring onto duct. Two manual chain falls were used to maneuver the ring. Ring weighed about 1000 lbs. Each chain fall was rated for 2200 lbs. A chain fall load chain broke, causing the ring to drop. EE states they felt the stiffener ring brush their forearm before landing on their thumb.

EE preparing to remove rigging from pad eye. EE was lowering hook using overhead crane. EE was detaching the shackle from the pad eye with gloved hands. The chain from the hoist had accumulated above the shackle and became caught on structure above pad eye. The hook from hoist rotated downward, EE's L thumb caught between the hook/housing and shackle. Contusion to thumb pad.

EE was moving a pallet jack loaded with iron when EE encountered a piece of 1/2 inch by 4 inch plywood covering an expansion joint on the floor. The pallet jack became stuck and as EE pulled hard to get it over the plywood, EE slipped and fell to the floor. EE also noted that there was salt and sand in the area where EE was maneuvering the iron.

The injured worker states that EE has right elbow pain. Today, while adjusting the pipe bender with a coworker, EE felt/heard a "pop" in EE's right elbow. There is no appreciable bruising at this time. There is no numbness/tingling into EE's hand or fingers. There are no open wounds

EE in a seated position had completed grinding and set grinder down. They then placed a hand on the duct next to the grinder that had not completely stopped spinning. As they applied weight to their hand to assist in standing up. The weight caused the grinder to slide toward their hand. The spinning wheel contacted the back of left hand resulting in a burn and laceration.