USMC Ione Plant: 669 citaciones de la MSHA Metal/Non-Metal

Using a cutting torch and had a splitsecond flash/flare up. Went to clinic for evaluation. Placed on modified duty until follow up.

Repairing a machine guard, caught right forearm on a sharp piece of metal and lacerated it. Took to emergency room and they stitched it closed.

Replacing a small motor and right ring fingertip got smashed. Suffered a broken fingertip and laceration.

Working to remove an out of service apron feeder. Tripped and unexpectedly stepped off to the ground approx 30" below. Had significant left knee pain. Taken to ER for treatment. Placed off work, awaiting MRI for better diagnosis.

IW descending a fixed ladder and fell. Left leg got caught in ladder safety cage or possibly ladder rung and caused a fracture left femur. Ladder is approx 17' high, worker fell approx 15 feet. IW transported to hospital by EMS.

IW sacking pallets of clay, began having mid back pain.

IW was hooking up a small water trailer to a pickup truck. In the process EE fell and reached out to catch self. EE's left pointer finger tip was caught in between the trailer hitch and ball. Approximately 1/2" of the tip was amputated. Taken to ER where they performed surgery to properly close the wound.

Walking and stepped on a drain grating. Grating shifted, allowed EE's foot to slide through to the concrete gutter/drain bottom. The grating lacerated IR's right shin in the process. Had a tetanus shot and 5 stitches to close up wound. Returned to work/no restrictions.

Used hammer to jar jammed knife gate free and shoveled sand. Had gradually increasing shoulder pain. Clinic diagnoses shoulder sprain/impingement and placed on restricted duty until follow up.

Manipulating a dump bucket lever and struck in shoulder by the bucket. Had an old non-work shoulder injury that was reaggravated. Placed on

Moving roofing tinwork at ground level on 1/25, 1/26 and 1/27. At some point began feeling pain in their back. Pain became bad enough 1/27/22 that EE then reported it and wanted to be seen for medical treatment.

Greasing upper bucket pin on front end loader. Worker was standing on a step approximately 24" above ground level. Worker's foot slipped and worker landed with back on the bucket.

Dresco pipe ruptured, whipped to the side and struck employee in the leg. Left lower leg fracture.

Slipped getting out of office chair, plopped back down into chair and jarred EE's back. Mentioned it to supervisor, but did not want medical tx at that time. Requested medical tx 8/4 due to lingering back pain.

Slip and fall at ground level near the drier pad, per employee they "tripped over our feet". Twisted ankle and knee. Did not initially want medical evaluation, but pain grew worse and they asked to be seen on 7/26/21. No diagnosis yet, other than "nothing broken, possible sprain/strain". Doctor put them in a knee brace and off work until after follow up visit on 8/9/21.

Foreign material in left eye. Believed to have occurred while grinding metal to prep for welding. Small metallic fragment removed from worker's left eye at medical clinic, with no permanent damage done. Worker was wearing proper PPE while grinding.

Sacking and stacking clay sacks, developed pain in left quadricep over time during shift.

Slipped and fell on bulk tank platform, struck edge of scaffold step with back. *For the sake of clarity, fall and landing were on the same level of scaffold.

Operates heavy equipment daily, complains of lower back pain.

Moving motor shaft during repair of water pump BC-213. Lost grip of motor shaft, dropped it onto left foot. Placed in a walking boot and cleared to return to full duty EE's following shift.

Field service technician dispatched to mine location, arrived at mine near shop location to start work on a downed piece of equipment. Upon exiting vehicle, stepped out onto some uneven ground and rolled an ankle.

Washing loader bucket out near sand screen. A check valve had failed and allowed caustic to back flow into the hose prior to this use. The employee was hit with over spray in the process of washing loader. Suffered chemical burns to arms, hands, belly, knee and foot.

Opening pickup tailgate, thumb got caught in the handle as the tailgate swung down. Employee suffered a left thumb sprain.

Climbing out of loader cab, missed the step causing EE to come all the way down to the ground with EE's left leg fully extended. Felt pain in EE's knee, diagnosed left knee strain.

The scraper behind EE hit hard while the two scrapers were linking up. EE had an onset of back pain over the next 5-10 minutes. Diagnosed as a "Back contusion".

EE was lifting ~5lbs of samples out of a lab machine and felt a sudden sharp pain towards the rear of left shoulder. Shoulder sprain.

Driving water truck daily. Employee developed back pain over the course of several days and reported it on 8/12/19. Back strain.

Stacking clay sacks, heard a popping noise and felt back pain.

A Truck raised EE's bed near high power lines. The lines arced to EE's truck causing damage to the tires. The driver was not injured. Staff was inspecting the scene when a tire blew causing their ears to ring. They were sent to a doctor for medical exam. The driver was not injured.

A Truck raised bed near high power lines. The lines arced to truck causing damage to the tires. The driver was not injured. Staff was inspecting the scene when a tire blew causing their ears to ring. They were sent to a doctor for medical exam. The driver was not injured.

While working near the surge bin, EE fell off an A frame style ladder approximately 3-4 feet. EE suffered lacerations to EE's right arm and head. Treated and cleared to return three days later.

Operating Dozer on gravel when a pre-existing hernia worsened. *for clarity, original cause of hernia was not work related.

I am doing an investigation. LOTO procedures were not followed.

Employee was picking up a battery moved the wrong way and tweaked their back.

EE was covering a pile of clay with a tarp when EE stepped onto what EE thought was solid ground. EE soon realized that the ground was giving way. EE fell and when EE was able to get up EE had extreme pain from EE's ribs.(It was raining at the time). EE notified EE's boss and boss took EE to the emergency room.

EE said to another employee that EE had bent down and when rising EE had twisted back. EE said needed to go home.

A kaolin plant EE was emptying a dump hopper and put hand on the lower rail, when the hopper rolled forward and then back it pinched hand. EE went to the doctor on 9/18/17 and was excused from work till 9/20/17. EE was returned to work full duty. We have since talked about this incident in safety meetings and added guards to equipment.

Conditions were good. EE was climbing water pull truck using 3 point contact. EE placed foot on Top step and slipped off losing balance. EE lost footing and grip and fell to the ground with most of the weight focused on the left foot. EE heard it crack. EE called safety manager and I took EE to the hospital. Result is a broken L-ankle .

Build moist cabinet for US Mine corp lab. Work shifted off stand while adjusting. Strained left shoulder not a problem at first. Became very pain full as soon ass I went to bed. Pain increased over night. Went to ER 5-6-17

At approx 8:00 am EE was on the middle wet screen area and attempting to take off a cover plate approx 24"x24" on a wet screen with a pry bar. While creating a gap to wedge open the lid, movement with the pry bar in an up down or "vertical" motion, EE right hand thumb was struck between the pry bar and a handrail near the wet screen.

EE, working with two other EEs, was cleaning up area with scattered debris. While working from a clear area through a debris pile, EE moved around to opposite side of pile to pull out a cable. While pulling backwards EE stumbled against a broken porcelain insulator attached to a cross arm. Insulator had a jagged edge that cut through pant leg above ee's boot lacerating skin.

AS EMPLOYEE WAS WALKING TO THE MAINTENANCE TRUCK HE FELT A ''POP'' IN HIS LEFT KNEE. BY THE TIME HE DROVE UP TO THE MAINTENANCE SHOP HE COULD BARELY WALK.

Employee was greasing equipment with a pressure grease gun. The hose on the grease gun failed (pin hole in hose) and injected grease into employees right index finger

Employee was removing cutting edge from a 657E scraper. The straight pry bar was being use to lift the cutting edge over the bolt (to free cutting edge). When the cutting edge freed up it slid down pry bar striking employee in hand.

EE was adjusting the track of conveyor belt. He was bent over looking under the cover. He placed his left hand on the cover to brace himself. His hand slipped and was pulled half way through the troughing idler.

WORKER'S BACK STARTED HURTING HIM AT THE LAST JOB HE WORKED. HE DID NOT REPORT HIS INJURY THEN. ON 7/14/05 WORKER NOTED ON HIS TIME CARD THAT HE HAD BEEN INJURED & WAS NOW REPORTING AN INJURY. HE CLAIMS THE PAIN HAS BEEN GETTING PROGRESSIVELY WORSE & NOW NEEDS MEDICAL ATTENTION. THE INJURY IS A RESULT OF OPERATING A SCRAPER, WORKER DOES NOT RECALL ANY SPECIFIC INCIDENT.

WHILE EMPLOYEE WAS LIFTING A SPARE PART, HE FELT A PAIN TO THELEFT SHOULDER. THIS RESULTED IN A STRAIN TO THE LEFT SHOULDER.

WORKING ON TROMMEL SCREEN AND PINNED HIS LEG IN IT AS IT ROTATED.

WHILE REPAIRING A LEAKING PIPE, THE INDIVIDUAL SLIPPED OFF A LADDER AND FELL APPROXIMATELY 3 FEET TO THE GROUND. THIS RESULTED IN A MINOR SPRAIN TO HIS BACK.

WHILE REPAIRING A MACHINE, EE BENT OVER TO PICK UP A BEARING. HE LIFTED THE BEARING HE FELT A PAIN IN HIS LOWER ABDOMEN. THIS INCIDENT WAS NOT REPORTED UNTIL 9/26/01. AT WHICH TIME HE WAS SEN T TO A DR & PLACED ON 14 DAYS OF MODIFIED DUTY

EE WAS LIFTING A GREASE BARREL AND FELT A PAIN IN HIS STOMACH. THE EE REPORTED THIS AT THE END OF THE SHIFT BUT SAID HE WAS OK. ON 10-24-01, EE SAID HIS TAOMCH WAS HURTING AND SAID IT WAS A RE SULT OF THE 9-14-01 ACCIDENT, EE WAS SENT TO THEDR ON 11-25-01 AND PUT ON RESTRICTED DUTY TIL 11-7-01.

EMPLOYEE WAS LYING ON HIS BACK LOOKING UP AT HIS WORK WHEN A PARTICLE FELL INTO EMPLOYEE'S EYE. HE RUBBED HIS EYE AND SCRATCHED THE CORNEA.

WAS PULLING ON ELECTICAL CABLE DURING A PIT MOV3& STRAINED HIS BACK

INATTENTION, LACK OF KNOWLEDGE, POOR POSITION OF SHUT OFF SWITCH, LACK OF OVERFLOW PIPING, POOR JUDGEMENT. EYE INJURY REQUIRED MEDICAL ATTENTION, SERIOUS.

WAS MOVING A SAW HORSE AND STRAINED HIS BACK WHEN HE MOVED IT.

SPRAINED LEFT WRIST WHEN PRY BAR KICKED BACK WHILE PRYING ON DRAGLINE TRAVEL GEAR.

WAS KNEELING ON FLOOR DOING SOME WIRE HOOKUP WHEN HE GOT UP SOMETHING PULLED IN LOWER BACK. TOOKMUSCLE RELAXER TO GET BACK IN SHAPE. TOOK NEXT DAY OFF AS SICK DAY

HAD A METAL BOX ON SAWHORSES AND WAS TRYING TO ROLL IT OVER AND GOT A STRAIN INLOWER BACK AREA.

SLIPPED OFF A PIPE WHILE PULLIING ON A WRENCH RETD TO WORK WITH 10LB LIFTING LIMIT UNTIL REPAIRED BY SURGERY Y

EE WAS CHECKING FEED ON AMINE INTO CONDITIONS-A DROP OF AMINE SPLASHED OFF OF CONDTIONS & INTO HIS EYE. EE WAS WEARING SAFETY GLASSES HOWEVER AMINE LANDED BEHIND THEM

WAS MOVING A BOX OF WELDING ROD & FELT SOMETHINGPULL IN GROIN AREA. WAS PUT ON WEIGHT LIFTING LIMIT OF 10LBS UNTIL SURGERY

LIFTING A PUMP & STRAINED STOMACH. HAD A 20LB WEIGHT RESTRICTION FOR 2 WKS

SCREWING SHEET METAL TO SIDE OF MILL, DRILL MOTOR CAUGHT FINGER.

LIFTING MAG ROLL AND TWISTED TO HAND TO ANOTHER PERSON AND STAINED LOWER BACK. 5 WEEKS THERAPY.

GROIN STRAIN WHILE JACK HAMMERING CONCRETE.

PULLING ON HEAVY ELECTRICAL CABLE AND PULLED BACK MUSCLES.

POURING CEMENT & TWISTED BACK. HAD TO GO TO THERAPY FOR 2 WKS.

PUT STEEL IN RACK WHEN SOMETHING POPPED IN LEFT RING FINGER. WENT BACK TO WORK, DIDN'T REPORT INJURY UNTIL 6/12/98. HAD TO HAVE SURGERY IN SEPT.

WORKER WAS WALKING TO JOB SITE WHEN HE STRUCK HIS HEAD ON LOW HANGING PIPE.

WORKER WAS REMOVING FLASHING WHEN IT BROKE LOOSE AND STRUCK HIM ON THE HAND.

EE CLEANING OFF CONVEYOR ROLLER & HIS GLOVE GOT CAUGHT ON ROLLER AND PULLED HIS HAMP AROUND IT.

BEARING PULLER SLIPPED STRIKING EE ON THE FOREHEAD RESULTING IN 6 STITCHES.

EE LEFT HAND RING FINGER INTO MAG SEP WHILE CLEANING WITH AIR HOSE

REPEATED SAME MOVEMENTS. LEFT AND RT ELBOWS POP AND HURT ALL OF THE TIME.

PULLING ON A COME ALONG HANDLE AND IT BROKE AND A SHARP PIECE OF THE HANDLE CUT HIS FINGER.

EMPLOYEE WAS SITTING SIDEWAYS IN A CONTOUR CHAIR IN LUNCH ROOM. HE LEANED INTO THE BACK OF THE CHAIR AND DISLOCATED A RIB OR PULLED CARTILAGE.

CONVEYOR BELT TOUCHED PVC PIPE & WORE A HOLE IN PIPE.

EMPLOYEE REPORTED THAT HE FELT SOMETHING IN HIS SHOULDER WHILE SHIFTING DRAGLINE. FOREMAN REQUESTED HE GO TO DR. THEN, HE SAID NO & WENT HOME 1200 NOON. WE MADE DR. APPOINT FOR NEXT DAY. DR. P OUT HIS ON 30# WEIGHT LIMIT & LT DUTY FOR 2 WKS.

RT ELBOW HAS BEEN BUMPED AND STRAINED OVER THE POST 7 YEARS ELBOW IN PAIN ALL THE TIME.

WORKING IN DRYER AREA SLIPPED ON CATWALK WHILE PULLING ON WATER HOSE PULLED LEFT SHOULDER WHEN FALL DOWN.

EE CALL IN ON 04-30-94 REPORTED HIS BACK HAD A STEADY PAIN & WSENT TO HOSPITAL ER ON 04-29-94 WANTED TO SEE COMPANY DOC ON 05-02-94

LIFTING 5 GAL PALE FULL OF WET SAND. (APPROX 100 LBS).

MIKE REPORTED FRO ORK ON 4-26-94 AT 12:00 NOON, HIS FIRST DAY BACK AT WORK AFTER WEEKEND, AT THAT TIME HE REPORTED HIS HACK HURT. WE SENT HIM TO COMPANY DOCTOR.

BOB CALLED IN TO REPORT HE STRAINED HIS BACK AT WORK ON 4-22-94, LAST DAY WORKED. REPORTED ACCIDENT TO US ON 4-25-94 AT 10:00. WANTED TO SEE COMPANY DOCTOR.

STEPPED INTO A HOLE WHILE WALKING.

OPENING 6IN DRAIN VALVE

WELDING 2" AIR PIPE TO I-BEAM CLAMP CAME OFF, PIPE HIT FACE & TEETH.

DRIVING DUMP TRUCK, HIT HOLE [IN] ROAD WHEEL SPUN, STOPPED WHEEL & SPRAINED RT ARM.

BENT OVER?

SLIPPED ON TOP OF DRY SAND BIN #5. THIN FILM OF SAND ON TOP OF BIN. TWISTED LEFT KNEE WHEN HE FELL.

GRINDER HUNG UP AND KICKED BACK, HANDLE HIT LEFT RIBS.

SLIPPED ON STEEL GRATING ON STAIRWAY. FOOT WENT UNDER STEP, HIT FRONT OF LOWER RIGHT LEG ON TOP OF NEXT UPPER STEP.

INSPECTING NEW TRACK INSPECTION CATWALK TIME LOST HIS FOOTING WHILE LOWERING A MOVABLE CATWALK.

HE WAS MOVING AN ELECTRICAL LINE IN THE PIT AREA OF THE PLANT. THE GROUND WAS SLIPPERY. HE WAS PULLING THE LINE ALONG THE GROUND TO GET IT OUT OF THE WAY. THIS WAS ON 7-16-91 AND HE REPORTED T HE ACCIDENT ON 7-17-91.

THE PIT STATION (BLUNGER) HE WAS WALKING ON LOWER LEVEL OF PIPE STATION ENROUTE TO STAIRWAY, FOOT SLIPPED ON PARTIALLY DRIED SLURRY MATERIAL.

CHANGING FROM #1 TO 32 PRODUCT WALKING BACK TO OPERATING LOCATION INJURED STOPPED/JUMPED OVER HISE LAYING ON THE GROUND,LANDED ON RIGHT FOOT TWISTING HIS ANKLE.

HIT HARD HAT ON STAIRWAY SUPPORTING BEAM AND JAMMED HIS UPPER SPINE AND NECK. MOUND OF DIRT WAS BUILT UP OUTSIDE.

DUCKING UNDER A CONVEYOR, HARD HAT BLOCKED VISION AND CAUGHT ON PIPE/BEAM AND JAMMED NECK.

HE WAS HOLDING METAL DOWN UNDER PRESSURE WITH A BAR TO BEWELDED, THE FLASH OCCURRED WHEN THE WELDING ARC REFLECTED OFF THE INSIDE OF THE DRYER CHAMBER.

HE WAS HOISTING THE BUCKET FROM THE MATERIAL HOLE TO THE HOPPER AND SOMEHOW THE HOIST LINE BECAME ENTANGLED IN THE CROWN POINT OR BOOM ASSY.THEREBY LIFTING THE ENTIRE BOOM UPWARDS UNTIL THE HO IST LINE PARTED DROPPING THE BOOM UNTIL IT WAS STOPPED BY THE BOOM SUPPORT ROPES,CAUSING THE MACHINE TO ROCK BACK AND FORTH THROWING HIM OUT OF HIS SEAT AND INJURING HIS NECK IN THE PROCESS.

HOLDING STOP BUTTON ,CHECKING PUMP COUPLING WITH LEFT HAND,PUMP STARTED UP AND MANGLED HAND REQ MEDICAL ATTENTION.

WHILE OPENING BOTTOM GATE ON BIN #4 WITH GATE TOOL HE SLIPPED & RIGHT HAND HT GATE SUPPORT STRUCTURE & INJURED HAND.

CLIMBING LADDER SLIPPED WENT TO GRAB THE LADDER WITH R HAND TO STOP FALL STRAIND R. WRIST FOREARM R SHOULDER.

SLIPPED ON WET FLOOR OF MILL, FLOOR HAS SLOPE FOR WATER DRAINAGE. CHECKING WITH TWO HOURLY EMPLOYEES IN BASEMENT OF WET MILL, WHILE THEY WERE WORKING ON WATER BOOSTER PUMP.

HOOKING TRAILOR TO TRUCK. FINGER WAS CAUGHT BETWEEN HITCH AND BALL, SPLITTING MIDDLE FINGER OF LEFT HAND.

PULLING A BOAT OUT OF AREA F WATER SUPPLY POND USING A ROPE BACK POPPED WHILE PULLING ON BOAT.

IN DRAGLINE WALKING ON DRAGLINE FLOOR, STEPPED ON ONE OF THE FLOOR HOLE COVERS AND IT FELL THROUGH INTO AREA UNDER FLOOR, HE FELL THROUGH FLOOR AND TWISTED RIGHT KNEE.

REPLACING DRAG CABLE IN 150B DRAGLINE PRY BAR. PRY BAR SLIPPED AND DRUG TOP OF HAND OVER EDGE OF DRAG DRUM.

REMOVING BEARING RACE FOR 10" PUMP SHAFT, APPLYING HEAT WITH TORCH USING 3 1/2 LB HAMMER A SLIVER OF STEEL LODGED IN LEFT SIDE OF BODY, JUST UNDER ARM.

KNIFE SLIPPED AND HE CUT TOP OF RIGHT THIGH WHILE REMOVING LIDS FROM USED OIL BUCKETS.

WHILE STRECHING3UPWARD TO THE UTMOST TO LIFT CABLE OVER OBSTACLE, LEFT FOOT SLIPPED AND LEFT KNEE POPPED CAUSING INSTANT PAIN AND STIFFNESS.

WALKING DOWN A WALKWAY SURROUNDED BY HAND RAILS THE EMPLOYEE TURNED THE CORNER ON THE WALKWAY AND BUMPED HIS LEFT ELBOW ON THE END OF THE HAND RAIL.

HE WAS HAMMERING ON THE SIDE OF A PLUGGED UP ELEVATOR. THE HAMMER CHIPPED A FRAGMENT OF STEEL OFF THE ELEVATOR & WENT INTO HIS FINGER.

DOING NORMAL WORK IN PIT STATION-DOESNT KNOW HOW IT HAPPENED.

TRYING TO CLOSE TIGHT BUTTERFLY VALVE WITH NO HANDLE.HE SLIPPED AND HIS FOREARM HIT PART OF THE STEEL STRUCTURE.

MOVING 12\\ IRON PIPE AND PIPE FELL ONTO LEFT FOOT.

HITTING A ROCK THAT WAS JAMMED IN A CHUTE.

PUTTING VARIOUS STORE ITEMS ON SHELVES PAIN JUST STARTED IN BACK

WHILE OPERATING DRAGLINE SOMETHING GOT INTO HISEYE.

USING HYDRAULIC CONDUIT BENDER, I NAME REMOVED A PIPE LUG TO CHECK THE OPERATION OF THE HYDRAULIC RAM, AND GOT A EYEFUL OF HYDRAULIC FLUID.

EMPLOYEE TURNED TO REVERSE DIRECTION WHILE FOOT WAS COVERED WITH SAND AND KEPT THE FOOT FROM MOVING CAUSING THE KNEE TO POP

CHANGING CABLE ON 150 DRAGLINE IN MINING AREA. HE WAS PULLING DEAD END OF CABLE, TO STRAIGHTEN CALB ERUN OUT TO THE FALL BLOCK WHILE BACKING UP AND STEPPED OVER THE EDGE OF THE PIT AND FELL AB OUT 12 FT. WHILE HOLDING ON TO CABLE HE BOKE LEFT SHOULDER BLADE.

WALKING AWAY FROM DROP BALL, WHEN HE TRIPPED OVER A ROCK FALLING ON HIS RIGHT KNEE & TWISTING IT.

WORKING ON Y FILTER TABLE CHANGING DRIVE SPROCKET-USING PRY BAR, SLIPPED AND JAMMED LEFT HAND-MIDDLE FINGER. CHIPPED BONE IN MIDDLE FINGER.

WORKING ON PUMP IN MILL AND SAND BLEW IN EYE

THE EMPLOYEE WAS PULLING A WELDING CYLINDER CART UP SOME STAIRS AS HE WAS PULLING THE CART UP STAIRS HE FELT A PAIN IN HIS LOWER ABDOMINALS.

MOVING SHETS OF CORRUGATED METAL SIDING AND SINS HHLLING ON SIDE OF NEW ELEC SHOP HE SOMEHOW TWISTED HIS BACK

4 MEN WERE LIFTING A 200 LB DISK ONTO A SHAFT. NEAL TWISTED HIS KNEE WHILE WALKING WITH IT.

SLIPPED ON MUDDY SURFACE AND TWISTED LEFT KNEE.

USING CHANNEL LOCK PLYERS HE WAS TIGHTENING PACKING GLAND ON A SAND PUMP.

WHILE GETTING OFF THE 46A CAT HIS FOOT SLIPPED OFF THE DOZER BLADE PUSH ARM & HE GRABBED THE HANDLE ON THE SIDE OF THE FLOORBOARD & TWISTED HIS BACK WHILE FALLING.

WHILE PUSHING CART & SHAFT INTO MILL WHEELS HIT CONCRETE APRON & JAMMED PUSH CART HANDLE INTO RIGHT SIDE OF GROIN AREA.

EMPLOYEE LIFTED A FULL LOADED BUCKET HIGHER THAN SHOULD BE AND TIPPED THE LOADER OVER PINNING HIMSELF BETWEEN THE LOADER AND RAIL

WORKING IN AREA WHERE WELDING WAS BEING DONE

GOT THUMB CAUGHT BETWEEN PUMP BOWL AND SUCTION STUBB ON X-19 PUMP.

PULLING ON A WRENCH AND IT SLIPPED HITTING LEFT ELBOW ON ANGLE IRON BEAM.

CROUCHED UNDER BELT GUARD,TIGHTING VEE BELT DRIVE PUSHING UP ON 18\\ PIPE WRENCH,FELT DISCOMFORT IN LOWER/MIDDLE PART OF BACK.

WALKING ACROSS WET MILL FLOOR ,STEPPED ON FILTER TABLE CLOTH DROPPED ON FLOOR CAUSING HIM TO SLIP AND FALL.BROKE THIGH BONE AND COMPLAINS OF BACK PAIN.