Buscar en el registro

Trying to close trailer gate - hinge portion would not close - pinched finger in gate.

Employee did not report a new injury at this time. Employee requested information on a previous injury from 2012. Stated the condition from the previous injury had returned, Old insurance company reported that the employee stated they picked up a bag and felt something in the same location of the previous injury.

EE states that he picked up 25 kilo bags and put them on a pallet. While lifting the bags something pulled in his groin area.

Employee states that ee felt twinge in back while pushing pipes around on floor with a cart and setting hoists up.

Employee was getting into his work truck, went to sit down and felt alot of pain in his back.

Employee was cleaning under the mixer, While shoveling he strained his back.

Employee was working on Door400, the 400 ton hopper Mega door. While working on the door, the fabric lifting strap that raises and lowers the door broke and the door fell 8-10' down and struck employee on the head knocking his hard hat off. The door then struck his left shoulder and forearm that was on the railing of the scissor lift.

Employee was working on classifier 230B trying to move a bound up part when his hand slipped off and collided with the classifier housing in an area that was worn to a sharp edge. Employees right hand grazed the sharp edge causing a laceration at the base of his right thumb that required sutures.

On 10/24/12 EE strained his rgt. side back and hip area while installing a water line. EE declined medical attention at that time. EE reports that on 11/28/12 he further aggravated the injury while performing the same task. He worked through the day. Worked 11/29/12 then sought medical treatment that evening in the emergency room and was placed out of work.

On 5/7/12 employee reported that on 4/29/12 he aggravated prior work related back injury while working in Beneficiation changing pipes. Back pain worsened so he sought medical attention on 5/1/12.

EE was putting expanded metal away in rack - it kicked up and cut left hand which required stitches.

EE was pulling stones out mill, lot of twisting and turning.

EE was pulling and pushing trying to get bag oof rolls.

Employee was going to fix a leaking transporter line. He was waiting for the line to depressurize when the line came apart blowing wollastonite all over him and into both eyes.

On 2/4/10 EE was trying to get ton bag off the run. He squatted, put his back to bag and pushed and felt pain in right knee (he declined medical attention on that day). On 3/3/2010 EE reaggravated knee, while stepping off portable ladder to the ground his knee gave out. Sought medical attention on 3/3/2010.

When rotating the classifier wheel pinched his finger between wheel and an obscure lip on the classifier body behind the wheel.

While employee was working on mill, he pinched palm of his left hand causing a laceration which required sutures.

While employee was installing shims in the ACM Mill classifier wheel he cut his thumb on one of the shims.

While employee was putting supplies away his hand brushed across the sharp edge of a bracket causing a gash to back side of left hand.

Employee states that while he was working on the tail pulley bearing on elevator 015 he went to turn around and ran his knee into a piece of steel jutting out.

EE STATES THAT HE WAS CHANGING THE AIRLOCKS ON LINE 2 (PLT. 2). WHEN HE LIFTED AIRLOCK HE HURT HIS BACK.

EE WAS CHANGING SEAT AND FLOP GATE ON VAC., VALVE ACTIVATED AIR PISTON AND END OF FINGER ON RT. HAND GOT CAUGHT.

EMPLOYEE STATES THAT WHILE BRUSHING SCREENS HE FELT A SPASM IN HIS LOWER BACK. STATES THAT HE STOPPED UNTIL SPASM WENT AWAY. HE STARTED BRUSH-ING SCREENS AGAIN AND THE SPASM CAME BACK. THIS TIME IT DIDN'T STOP.

WHILE TWO OTHER EMPLOYEES WERE PULLING EE OUT OF #1 PEBBLE MILL (ONE ON EACH ARM), THE MAN ON HIS LEFT ARM PULLED TOO HARD.

WHILE EMPLOYEE WAS DUMPING 99 LB. BAGS OUT BACK, HSI SHOULDER PULLED OUT.

WHILE EE WAS WORKING ON #2 PEBBLE MILL--NEW FEED SPOUT--DUST WAS FALLING AND GOT INTO HIS EYES.

WHILE EE WAS CHECKING AN AIRLOCK THE TIP OF HIS MIDDLE FINGER, LEFT HAND, GOT CAUGHT BY THE AIRLOCK 211A AND WAS CUT OFF.

EMPLOYEE STATES THAT WHEN PULLING ON BAG LOPS HIS BACK CAUGHT.

WHEN EMPLOYEE WAS PULLING AN EMPTY BAG ON BAGGER HE REACHED OVER AND PULLED HIS BACK.

WHILE EMPLOYEE WAS GETTING OFF THE FORKLIFT HE CAUGHT HIS FOOT UNDER THE GAS PEDAL CAUSING HIM TO TWIST HIS RIGHT KNEE.

EE WAS HELPING ANOTHER EE PICK UP A 20' PIECE OF HEAVY WALL PIPE(USING THE PROPER LIFTING TECHNIQUE) BUT TWISTED ONE THE PIPE WAS IN A RAISED POSITION CAUSING LOW BACK MUSCLE STRAIN. EE DID NO T BEGIN LOSING TIME UNTIL 5/29/98.

EMP STATES THAT WHILE HE WAS WASHING A GLASS BEAKER THAT HAD A CHIP ON THE TOP WHICH HE DID NOT DETECT BEFORE WASHING IT HE CUT THE PALM OF LEFTHAND WHICH REQUIRED STITCHES.

EE WAS ATTEMPTING TO CALIBRATE A BULK SCALE. HE & ANOTHER EE WERE USING A FORK LIFT TO PUT A 2000 LB. TEST WEIGHT ON SCALE. HE PUSHED ON WEIGHT.

EMPLOYEE STATES THAT HE WAS SHOVELING AND SWEEPING GARNET AND ROCK WASTE WHEN HE FELT A SUDDEN PAIN IN HIS RIGHT LOWER BACK, RIGHT SHOULDER AND ELBOW.

EE STATES THAT WHILE HE WAS CLEANING UP AROUND BAGGER PICKING UP OLD PALLETS 70LBS AND CARDBOARD HE FELT SEVERE PAIN IN HIS LOWER LUMBAR AREA.

WHLE EMPLOYEE WAS UNLOADING BARRELS OF 200 & C101 OFF DOCK INTO LOADER BUCKET, A BARREL DROPPED AND LANDED ON HIS RIGHT FOOT.

WHILE EE WAS UNPLUGGING FEED CHUTE ON #1 PEBBLE MILLE HE STATES THAT HIS HAND SLIPPED AND SCRAPED A SHARP PIECE OF METAL (ANGLE IRON).

WHEN EMPLOYEE BENT DOWN TO PICK UP A SAMPLE KNIFE THAT HE DROPPED ON THE FLOOR HE PULLED HIS BACK.

WHILE EMPLOYEE WAS WORKING ON PEBBLE MILL A MAN INSIDE MILL HOLLERED TO HIM TO HAND HIM A BOX OF TILE WHEN EMPLOYEE TURNED HE RAN HIS HEAD INTO BOLT

EMPLOYEE WAS MOVING TRUCK TIRES AROUND ON THE STOCKPILE WHEN HE FELT PAIN IN HIS BACK.

EMPLOYEE PULLED BACK WHEN LIFTING ON AUGER OF SCREW 54.

EE TRIED TO MOVE A GAYLORD BOX BY HAND & PULLED A MUSCLE IN HIS BACK.

EMPLOYEE WAS CHANGING PLATES IN F-1 MILL HE CUT HIS INDEX FINGER IN LIP OF HEAD. EDGE OF HEAD IS SHARP. EMPLOYEE RECEIVED 4 STITCHES.

WHILE EE WAS TRYING TO INSTALL SLIDE TO WORK ON FEEDER HIS HAND SLID ACROSS SLIDE TEARING HIS LEFT PALM OPEN. SLIDE HAS BEEN HAMMERED ON SO MUCH THAT THE FLAT EDGE HAS BECOME RAZOR SHARP. EE R ECEIVED 4 STITCHES.

EMPLOYEE WAS ROLLING A BARREL OF SCREEN OVERSIZE ONTO A PALLET WHEN HIS BACK GAVE WAY. EMPLOYEE WAS UNABLE TO STRAIGHTEN UP.

EMPLOYEE WAS SHOVELING UNDER CONVEYORS WHEN HE PULLED MUSCLE IN BACK.

WHEN EMPLOYEE BENT DOWN TO PICK UP AN EMPTY PALLET HE PULLED A MUSCLE IN HIS BACK.

WAS CLEANING MAGNETS ON EXOLONS AND PERMROLLS. WHILE REMOVING MAGNET FROM 23 PERMROLL HE FELT A TWINGE IN HIS BACK. BY THE TIME HE WASLKED TO THE LAB MUSCLE HAD TIGHTENED UP.

WHILE THROWING BAGS BACK THROUGH A BAG FLATTENER, EMPLOYEE FELT A TWINGE IN HIS BACK.

WHILE INSTALLING A TWO INCH VALVE, EE DROPPED THE VALVE WHILE HE WAS TRYING TO CATCH IT THE VALVE STRUCK HIM IN THE RIGHT HAND INJURING THE 3RD JOINT IN THE LITTLE FINGER.