Buscar en el registro

On 9/27/24, employee was tightening 5/8" bolts with two wrenches when EE felt a sharp pain in the wrist. EE's wrist and hand became swollen. An x-ray revealed EE had a small piece of metal embedded in their hand from a scratch EE received the day before. Medical professionals removed the metal from EE's hand. EE's wrist was only strained.

Employee was dismantling a piece of equipment on the floor of the shop, EE stuck the back of EE's hand on a nearby wooden pallet and received an 1 1/2" long sliver in the back of EE's hand. Medical personnel cut the skin to push the sliver through to remove it.

Changing screen and finger got pinched between bolt lock and side plate.

Truck driver forgot to latch the tailgate before being loaded. EE tried to clear stones from the latch by hand. EE's fingers got pinched by the tailgate and lacerated by the latch.

Company electrician was lifting a 40lb roll of wire into a van from the ground and injured their shoulder. Electrician did not lose time at the time of the incident, but needed surgery to repair the injury on 11/28/2018.

Employee was bending over to put a steel cover on a pontoon when EE felt a sharp pain in EE's lower back.

Two employees were hand-loading a fuel pump into the bed of a pick up truck. As they set the unit down, One employee had finger crushed by the pump base. EE had surgery to repair the finger on 11/17 and returned to work on 11/21. EE is currently on restricted duty.

Employee was turning a 4-sided die on the press brake. One end of the die slipped off the support chain and crushed the employee's finger.

employee was stepping up onto the step on an excavator when he felt a pop and tear in his left calf.

Employee was lathing bushings in a loader bucket. A large metal shaving was stuck to the boring bar and the employee grabbed it with his gloved hand to break it off and cut his finger. The laceration required stitches to close.

Employees were removing steel plate and rebar from a pallet that was raised on a forklift. The supervisor instructed the forklift operator to lower the pallet. Instead, the operator moved the forklift back as the supervisor was removing a piece of rebar. The rebar dislodged a piece of plate which fell onto the assisting employee's foot.

Employee picked up a can of welding rods. A sharp edge on the can caused a cut to the employee's thumb.

EMPLOYEE WAS DISASSEMBLING A CRANE BOOM WHEN THE SUPPORT SECTION FELL OFF OF THE BOOM, ONTO THE EMPLOYEE'S FEET.

EE WAS WORKING ON A HAUL TRUCK WHEN STEEL HYDRAULIC SUSPENSION LINE BROKE. PRESSURE CAUSED OIL TO HIT RT FOREARM CAUSING ABRASION & HEMOTOMA TO IT AND SPRAYING OIL ON CLOTHING.

EMLOYE ESTEPPED OUT OF A CABOVER TRUCK HE WAS DOING MAINTENANCE ON. HE BRUISED HIS RIGHT HEEL.

INSTALLING A DRIVE CHAIN ON DRYER AT BLACKTOP PLANT.

EMPLOYEE WAS PERFORMING ENGINE WORK ON TK#84, LIFTING OFF HEADS. INJURY DUE TO STRETCHING AND LIFTING.

EMPLOYEE WAS PUTTING SCRAP METAL INTO A DUMPSTER ACROSS THE ROAD. WHEN HE GOT BACK TO THE SHOP HIS BACK GOT PROGRESSIVELY SORER.

EE WAS ATTEMPTING TO REMOVE FROZEN CHUTE FROM PLANT. WHEN CHUTE BROKE LOOSE IT PINCHED RING FINGER BETWEEN CHUTE AND SCREEN. EE WAS WEARING GLOVES, SO EXTENT OF INJURY WAS NOT VISIBLE. WE TOOK HIM TO HOSPITAL. THEY MOVED HIM TO ANOTHER HOSPITAL WHERE FINGER WAS REMOVED.

EE WAS ACID WASHING A DUMP TRAILER. ACID WASH SPLASHED INTO EE S RIGHT EYE CAUSING A BURN TO RETINA. EE WAS USING SAFETY EQUIPMENT INCLUDING RAIN SUIT SAFETY GLASSES AND RUBBER GLOVES.

WHILE WORKING IN SHOP--PIECE OF STEEL WENT IN EYE. EYE WAS FLUSHED OUT.

EMPLOYEE TWISTED RIGHT KNEE X RAYS SHOW TORN CARTILAGE.

CARRYING A STEEL DOOR, HIS LEG SIMPLY BROKE.

54736YEE WAS MOVING STEEL APPARENTLY PIECE OF RUST WENT INTO LEFT EYE

IT IS ALLEGED EMPLOYEE WENCHED BACK WHILE PULLING WIRE FOR PLANT.

EMPLOYEE WAS BRAZING ON OIL PAN. DRIP PLUG BLEW OUT AND HOT OIL DRIPPED ON HAND AND ARM.

EMPLOYEE PULLED3MUSCLE IN BACK WHILE PUTTING CROSS FRAME IN TRUCK

IT IS ALLEGED THAT WHILE EMPLOYEE WAS LIFTING HE NOTICED A PAIN IN BACK.