Buscar en el registro

EMPLOYEE WAS STANDING ON LADDER USING HAMMER TO REMOVE RUST FROM OLD BEAM SO HE COULD LAY OUT HIS HOLE PATTERN ON OLD BEAM. WHILE HAMMERING, AN OBJECT FROM ABOVE FELL AND HIT THE EMPLOYEE IN THE LEFT ARM.

EE WAS CUTTING ACROSS A 42" CONVEYOR BELT, THE BELT WAS WADDED UP SO A BELT CUTTER COULD NOT BE USED AT THIS TIME. WHEN EE GOT TO THE EDGE OF THE BELT, THE BLADE CAME THROUGH & STRUCK EE IN RT THIGH RESULTING IN A SMALL LACERATION THAT REQUIRED 1 SUTURE TO CLOSE WOUND. EE RTW NORMAL DUTIES.

THE EE WAS SHOVELING SALT AT THE BOTTOM OF THE 14' SHAFT AS SHE TWISTED TO THROW THE SALT OUT OF THE SHOVE, SHE FELT A PAIN IN HER LOWER LEFT SIDE. SHE HAS CONTINUED TO WORK AT HER REGULAR OCC UPATION, BUT HAS BEEN SCVHEDULED FOR THERAPY THE WEEK OF 10-8 AND 10-15, 3 TIMES A WEEK.

EE WAS REMOVING THE INSULATION ON THE TERMIANTION END OF AN ELECTRICAL CABLE USING KNIFE BLAD OF A MULTI TOOL DEVICE. THE KNIFE BLAD SLIPPED OFF THE INSULATION & CUT EE'S LEFT THUMB. LT. THUMB LACERATIN REQUIRED 2 SUTURES. NO RESTRICTIONS.

THREE EE'S WERE PULLING A 3' X 7" METAL PLATE WITH A COME-ALONG FOR OUTSIDE FOR #4 BIN. A 2" X 12" BOARD WAS BEING USED AS A GUIDE FOR THE PLATE TO SLIDE ON. ONE EE PULLED THE COME-ALONG & THE OTHER TWO EE'S GUIDED THE PLATE ACROSS THE HAND RAIL. THE PLATE SLIPPED AND ONE EE GOT L THUMB CAUGHT BETWEEN THE BOARD & METAL PLATE. RESULTED IN LACERATION REQUIRING SUTURES & MODIFIED DUTY

EE WAS REMOVING 3/4" MOUNTING BOLT FROM BASE OF 150 HP MOTOR. A 1 1/8" COMBINATION WRENCH WAS BEING USED. AS EMPLOYEE PUSHED WITH EXCESSIVE FORCE TO REMOVE BOLT, WRENCH SLIPPED CAUSING WRENCH TO HIT EE ON CHIN RESULTING IN LACERATION TO CHIN THAT REQUIRED SUTURES.

EE WAS CUTTING BOLT HOLE NOTICES IN WIPER MATERIAL. EE WAS HOLDING BELT WITH LEFT HAND AND PUSHING KNIFE AWAY FROM BODY WHEN BLADE SLIPPED. THIS CAUSED LACERATION TO THE BACK OF THE LEFT HAND BETWEEN THE THUMB AND FOREFINGER.

EE WORKING ON BELT FILTER ROLLER BEING SUSPENDED BY A COME-ALONG WITH HELP FROM FELLOW EE. AS ROLLER WAS BEING PRIED WITH BAR, THE BAR SLIPPED CAUSING ROLLER TO SWING AND EE GOT FINGER CAUGHT BETWEEN THE BEARING AND FRAME.

EE WAS REMOVING COME ALONG AFTER INSTALLING NEW EYE BOLT ON VIBRATOR FEEDER #1 AT K-MAG. SLACK DEVELOPED ON SAFETY CABLE CAUSING SLACK ON COME ALONG. WHEN SLACK CAME OUT OF SAFETY CABLE, EXTRA TENSION DEVELOPED ON THE COME A LONG CAUSING EE TO PINCH RIGHT THUMB.

EMPLOYEE WAS REPLACING THE HEAD SHAFT ON #2 STACKER. HE HDA REMOVED THE END BELL ON THE RECLAIM CONVEYER MOTOR TO ALLOW IT TO TURN TO GET SLACK IN THE CONVEYER CHAIN TO PIN IT BACK TOGETHER. AS EMPLOYEE WAS TURNING ONE MOTOR FAN WITH ADJUSTABLE WRENCH, THE ALUMINUM FIN ON THE FAN BLADE BROKE. WHEN IT BROKE. IT CAUSED EMPLOYEE TO SLIPFORWARD, CUTTING RIGHT LEG ABOVE KNEE.

EE SMASHED HIS LEFT THUMB WHIL TIGHTENING A BOLT. THE BOLT BROKE AND HIS THUMB WAS SMASHED BETWEEN THE SCREEN FRAME AND THE RACHET HANDLE.

EE WAS TIGHTENING BOLTS WHEN THE RATCHET HE WAS USING SLIPPED CAUSING HIS RIGHT ELBOW TO HIT A STAINLESS STEEL CABLE TRAY, LACERATING RIGHT ELBOW APPROX 1" LONG

EE WAS RELOCATING SPRAYBARS FROM SHOP TO P-22 AREA. STACKING ON SHELF (WAIST HIGH) WHILE STACKING 2ND SPRAYBAR CAP ON END TURNED & SPRAYBAR SLIPPED OUTOF HAND, FELL & HIT KNEE

EMPLOYEE WAS TRYING TO PUNCH A HOLE IN AN ELECTRICAL CABINET. WHILE PULLINGON A WRENCH THE PUNCHBROKE, RESULTING IN EMPLOYEE SLIPPING AND FALLING OFF OF THE STEP LADDER HE WAS WORKING OFF OF.

4 FT AIRLEG WAS SECURED IN A VISE AT ONE END AND AN 18"PIPE WRENCH WAS ATTACHED TO A FITTING ON THE OTHER END. DOWNWARD PRESSURE WAS APPLIED TO THE HANDLE OF THE WRENCH. THE FITTING CAME LOOSE AND WRENCH (AND HAND) CAME DOWN QUITE ABRUPTLY ONTO THE WORK BENCH. HANDLE BROKE THE FINGER.

THE EE WAS CLEANING OFF SOME BUILDUP IN THE #5 DRYER WITH A ROD SCRAPER BAR WHEN A PIECE OF THE BUILDUP SUDDENLY BROKE OFF, CAUSING HIM TO STRIKE HIS LEFT HAND AGAINST THE BOTTOM OF THE OPENIN G BREAKING HIS RING AND LITTLE FINGER.

EE WAS HELPING REMOVE A COUPLING ON A GRAULATION PINION. EE WAS HOLDING A PROPANE BURNER WHIOE OTHER EES STRUCK A PULLER PLATE WITH HAMMERS. EE WAS IN FRONT OF COUP;LIGN WHEN PULLE ALL-THREAD PULLED THROUGH THE NUT. EE WAS STRUCK ON BOTH SHINS WITH EITHER THE ALL-THREAD OR PULLER BAR.

THE EE WAS USING A SLEDGE HAMMER TO BEAT ON A PLUGED CHUTE AND SMASHED HER RIGHT INDEX FINGER BETWEEN THE CHUTE AND HAMMER. 4 STITCHES WERE REQUIRED ON HER FINGER. SHE RETD TO HER JOB AT FULL CAPACITY THE NEXT SHIFT

EE WAS USING A JACK TO RAISE A STORAGE UNIT TO REMOVE A RETURN ROLLER. EE HAD BOTH FEET ON THE JACK HANDLE AND THOUGHT THE JACK HAD SET, BUT IT HAD NOT AND WHEN HE RELEASED THE PRESSURE ON THE JACK THE HANDLE CAME UP HARD AND FAST, INCHING HIS LEFT FOOT IN THE JACK.

EE WAS REMOVING A BAD FLIGHT FROM A CONVEYOR CHAIN. AS HE HIT THE CHAIN LINK WITH A SLEDGE HAMMER, A METAL SLIVER STRUCK HIS RIGHT LOWER LEG ANDS BECAME EMBEDDED. THE INCIDENT BECAME REPORTABL E ON 4-2 WHEN THE SLIVER WAS SURGICALLY REMOVED ON AN OUTPATIENT BASIS.

AS EMPOLOYEE USED A CABLE HOOK TO MOVE THE CONTINUOUS MINER CABLE, HE STATED HE FELT PAIN IN HIS UPPER BACK.

EE WAS USING A 16" ADJUSTABLE WRENCH TO TIGHTEN BASE BOLTS IN #4 REACTION TURBO. HE SAT ON THE GRATING AND USED HIS LEGS AGAINST THE HANDRAIL FOR LEVERAGE. EE STATES HE FELT NO PAIN AT THE TIM E, BUT DEVELOPED LOW BACK PAIN SOMETIME LATER. HE NOTIFEID THE SAFETY DEPARTMENT ON 1/19/98.. HIS DUTIES WERE RESTRICTED ON 1/26/98

AS EMPLOYEE USED A KNIFE TO CUT RUBBER BELT, THE KNIFE SLIPPED AND LACERATED HIS RIGHT THIGH.

EMPLOYEE WAS REPLACING THE WOODEN HANDLE ON A HAMMER. AS HE STRUCK THE HANDLE TO SEAT IT INTO THE HAMMER, THE WOOD SPLINTERED AND PUNCTURED HIS LEFT HAND.

AS EE BARRED DOWN A SLAB IN HIGH MINE BACK, HE STATED HE FELT PAIN IN HIS LEFT LOWER BACK.

EE WAS ATTEMPTING TO HANG A PRIMARY POWER CABLE ON HOOKS IN 12' MINE BACK USING A 6' INSULTED FORK. WHEN THE CABLE MISSED THE HOOK, THE WEIGHT PULLED THE FORK SIDEWAYS CAUSING PAIN IN THE EE S RIGHT ELBOW. THE EE HAD A PREEXISTING CONDITIONIN THE ELBOW.

AS FOUR EE WORKED TOGETHER TO BAR DOWN A LARGE SLAB, ONE EE FELT A PAIN UNDER HIS RIGHT SHOULDER BLADE.

EMPLOYEE WAS INSTALLIGN A COUPLING TIRE, WHICH WAS SUSPENDED BY A COME-A-LONG, ON #1 RAYMOND MILL ROLLER DRIVE. WHEN THE TIRE SLIPPED, THE FINGERS OF HIS RIGHT HAND WERE PINCHED BETWEEN THE O PENING IN THE TIRE CENTER AND THE MOTOR COUPLING HALF.

AS A STORAGE & LOADING EE ATTEMPTED TO PRY OPEN THE BOTTOMDOOR ON A RAILCAR USING A SHORT BAR, THE BAR SLIPPED AND MASHED HIS RIGHT LITTLE FINGER BETWEEN THE BAR & RAIL

AS EE BENT FORWARD AND PULLED ON AN 18" PIPE WRENCH TO REMOVE A LUG BOLT ON A RAMCAR, HE FELT PAIN HIS RIGHT LOWER BACK. HIS DUTIES WERE RESTRICTED ON 8-15-96 BY HIS PHYSICIAN.

A BELT CREW EE SLIPPED WHILE USING A CRAFT KNIFE AND LACERATED HIS LEFT THIGH.

AS EMPLOYE EUSED A PIPE WRENCH TO LOSOEN A FITTING, HIS FINGER WAS CUAGHT BETWEEN THE WRENCHA DN A ANGLE IRON BRACE.

EMPLOYEE STATED THAT HE USED A BAR AND CHAIN TO LIFT A BOOM LIFT JACK. THE FOLLOWING DAY, HE FELT PAIN IN HIS LOWER BACK. THE INCIDENT BECAME REPORTABLE ON 8-26-94 WHEN EMPLOYEE REQUESTED A DO CTOR.

AS EMPLOYEE USED A SLEDGEHAMMER TO REMOVE BUILDUP FROM A DRIER FEED CHUTE, HE FELT PAIN INHIS RIGHT UPPER FOREARM AND ELBOW. THE INCIDENT BECAME REPORTABLE ON 6-9-94 WHEN HE WAS PLACED ON RESTRICTED DUTY.

AS AN UNDERGROUND MAINTENANCE EMPLOYEE WAS USING A HAMMER T0 DRIVE A PIN OUT OF A CONVEYOR DRIVE CHAIN, HE LOST HIS GRIP ON THE HAMMER WHICH STRUCK THE INSTEP OF HIS LEFT FOOT RESULTING IN A B RUISE.

WHILE EMPLOYEE WAS CLEARING A BLOCKE DHOPPER, A 2X4 BOAD WHICH WAS BLOCKING THE HOPPER BROKE FREE. HIS THUMB WAS STRUCK BY THE BOARD RESULTIGNIN A HAIRLINE FRACTURE.

AS EMPLOYEE WAS CUTTING A SECTION OF CONVEYOR BELTING WITH A KNIFE, THE KNIFE SLIPPED AND STRUCK HIS RIGHT LEG JUST ABOVE THE KNEE. THIS RESULTED IN A CUT THAT REQUIRED SUTURES TO CLOSE.

AS EMPLOYEE WAS ATTEMPTING TO BREAK A BOULDER WHICH WAS LODGED BEHIND THE PUSH PLATE OF A RAMCAR, HE MASHED TWO FINGERS ON HIS RIGHT HAND. THIS RESULTED IN A BROKEN INDEX FINGER & AMPUTATION A TO THE FIRST JOINT OF THE MIDDLE FINGER.

EE WAS KNOCKING OFF CAMLOCK WITH HAMMER PUNCH WHEN RUBBER GRIP SLIPPED CAUSING EE TO HIT LEFT THUMB.

AS EMPLOYEE WAS INSTALLING A COUPLING PIN IN THE TRACK ON A LOADING MACHINE, A PIECE OF METAL BROKE OFF OF THE PUNCH HE WAS SUING & ENTERED HIS LEFT SECOND FINGER.

EMPLOYEE WAS SHARPENING KNIFE WITH SHARPENING STICKS. ATTENTION DIVERTED AND MISSED STICK AND STRUCK FINGER WITH KNIFE.

EMPLOYEE HAD SHORT-END WRENCH ANCHORED UNDER BOLT & STUCK THROUGH FLANGE OF PIPE WHILE USING ANOTHER OPEN-END WRENCH TO REMOVE NUT THE AMOUNT OF PRESSURE BEING APPLIED TO BREAK NUT LOOSE CAUSE D SHORT WRENCH ON HEAD OF BOLT TO SLIP & FLY UP & HIT HIM OVER RIGHT EYE

AS EMPLOYEE WAS CHANGING BITS IN A CUTTING MACHINE HE PULLED ON THE BIT WRENCH & FELT A PAIN IN HIS BACK

EMPLOYEE REPORTED TO HER SUPERVISOR ON 6-24-92 THAT SHE THOUGH SHE HAD GOTTEN A PIECE OF METAL IN HER EYE THE DAY BEFORE WHILE PERFORMING MAINTENANCE WORK ON THE LANG CLASSIFIER. SHE WAS TRANS PORTED TO A DOCTOR FOR REMOVAL OF A SMALL EMBEDDED METAL.

AS EE WAS ADJUSTING THE TRACK ON A JOY LOADING MACHINE, THE WRENCH HE WAS USING SLIPPED OFF THE BOLT, CAUSING HIM TO STRIKE HIS RIGHT ELBOW ON THE CONTROL PANEL OF THE MACHINE.

EMPLOYEE WAS USING POCKET KNIFE TO TRIM AND REMOVE BROKEN HANDLE OF B & O.BLADE CLOSED SLICING SIDE OF LEFT HAND INDEX FINGER.

USING HAMMER AND WEDGE AND HIT FINGER

EMPLOYEE WAS TRYING TO REMOVE TRAP DOOR HOPPER WAS CHOKED OFF SHE WAS UNABLE TO TURN NUT I NAME ASSISTED BY TURNING NUT & SHE HELD WRENCH ON BOLTHEAD ON BACK OF DOOR WRENCH SLIPPED MASYING FIN GERS ON DOOR HANGER HINGE

WHILE IN PROCESS OF REMOVING THRUST BEARING FROM COLLAR,BY TAPPING LIGHTLY WITH HAMMER,A PICE FROM BEARING SHATTERED OFF AND STRUCK EMPLOYEE IN RIGHT KNEE.

EMPLOYEE WAS REMOVING A BUSHING FROM A BOOM ON A JUMBO DIRLL USING A HAMMER AND BRASS PUNCH AS HE SWUNG THE HAMMER, IT STRUCK THE MACHINE FRAME, CAUSING THE HAMMER TO MISS THE PUNCH AND HI T HIS HAD A GLANCING BLOW. ALTHOUGH THE X-RAYS WERE NEGATIVE & NO MEDICAL TREATMENT WSA RENDERED, THE EMPLOYEE'S ACTIVITIES WERE ALTERED DUE TO THIS INCIDENT.