Buscar en el registro

Employee was changing out a bearing on a hydrator. While lowering the bearing it slipped and fell onto employee's right foot causing bruising and swelling.

Employee was trying to put a track back on the drill. The bar the employee was holding was pulled out of EE's hand when the track moved causing a sore shoulder.

Employee was tightening fittings with a pipe wrench and struck elbow on a steel door frame on 2/10/22. Employee was checked at a clinic on 2/11/2022 and released to work with no treatment or restrictions. Employee returned to clinic on 2/22/2022 due to swelling and was placed on work restrictions.

Employee was raking clinker when a piece of dust got behind face shield and safety glasses and in eye causing irritation. The employee was seen by a Dr. and issued a prescription.

An employee was repairing a conveyor belt using a belt cutter to cut the belt. While turning the handle on the belt cutter, EE felt pain in the right shoulder, resulting in a strain. EE was seen at a clinic and prescribed pain medication.

Employee was using a 12" ratchet to remove a coupler fitting when ee felt a pop in right forearm. EE reported it on 10/13 but did not seek medical treatment until 10/24 and was placed on work restrictions for a possible torn ligament.

Employee was using a pick ax to clear built up material for a rail and tie inspection. Employee's arm began to hurt the next morning. Employee was sent to the Urgent Care where employee was diagnosed with tendinitis in the left forearm and placed on restricted duty.

Employee was cleaning out a pipe with a plunger hand tool and EE's finger was pinched between the wall of the pipe and the handle of the tool.

EE was barring down clinker in the preheater transition chute when ee felt a "pop" in right elbow accompanied by numbness in hand and fingers. EE was treated by a physician for an injury/irritation of the ulnar nerve and placed on restricted duty pending clearance to return to full duty.

EE was part maintenance crew removing/shooting clinker from K-2 Preheat Tower. EE was in a seated position shooting the kiln gun, when EE felt something hit left thigh. EE was taken to ER - received treatment to remove a fragment of the kiln-gun slug that ricocheted and struck EE. EE was discharged and is waiting to return to full duty pending clearance from the physician.

EE lacerated the little finger on right hand while attempting to pry open a sliding gate on a coal chute with a bar. Hand contacted an electrical bracket, cutting finger. The wound required 4 sutures to close - the employee returned to full duty with no restrictions.

Employee was stripping a metal-clad jacket from a cable with a Linesman Pliers. The lineman's pliers slipped and struck the employee in the mouth chipping front tooth.

EE strained EE's right shoulder while barring/chipping clinker down from the K-2 Pre-Heat Tower. EE was treated by a physician on 2/25/2016 and placed on restricted duty pending follow up and release to full duty.

EE was replacing wedge plates on a crusher, while swinging a hammer to remove hardware he suffered a shoulder strain. He was treated by a physician and placed on lifting restrictions pending a follow up appt.

EE was barring/cleaning material off of interior of lime kiln walls - informed Supervisor the following day that he was suffering from muscle weakness and spasms in his shoulder-primarily on left side. Phys. has placed him on lifting restrictions with Rx. for muscle relaxers/anti-inflammatory meds. Follow-up appt. sched. for 4/29.

Employee was in the baghouse cleaning the rust scale buildup on the walls of a baghouse. He was using a scraper mounted on an 8' pole. The scraper was leaning up against the wall and was inadvertently bumped, causing it to fall down. The blade struck him causing laceration to right calf. He went to emergency room where he received stitches.

Struck finger with hammer. Resulting in laceration on left index finger.

Maintenance technician was tighening a tension rod nut for the Roll crusher. He was using a 2 1/4" combination wrench (2 1/2 feet long) to tighten the nut. He pushed up on the wrench and heard a popping noise and noticed sharp pain in his right shoulder.

prying down with bar to get a screen to go into place when it slipped and smashed left middle finger

Swinging sledge hammer against sides of rock hopper to unplug jam, felt pain in shoulder.

Cleaning Ducon (scrubber) at Hydrate plant, chipping lime and got a piece of it in eye.

EE WAS ADJUSTING THE BELT TENSION BETWEEN THE CRUSHER AND THE MOTOR, WHEN HE GRABBED THE ADJUSTING HANDLE AND ROTATED IT. "AT THAT TIME I HEARD OR FELT A 'POP' IN MY LEFT BICEP AREA."

PULLED BACK MUSCLES WHILE SWINGING HAMMER TO OPEN A SLIDE.

EMPLOYEE WAS TRYING TO GET A LARGE ROCK OUT OF THE RIGHT REAR DUEL TIRE ON THE WATER TRUCK WITHA SLEDGE HAMMER. WHEN HE HIT THE ROCK, THE IMPACT BOUNCED OFF THEN THE SLEDGE HAMMER HIT THE TOP OF THE RIGHT FENDER, BOUNCED OFF IT AND HIT HIM ON THE RIGHT SIDE OF THE HEAD.

EE WAS TIGHTENING BOLTS ON A CRUSHER AND STRAINED WHILE USING HIS WRENCH. RESULTED IN A STOMACH HERNIA.

EE & ANOTHER EE WERE ATTEMPTING TO TURN WHEELS ON AN AXLE. EE WAS PULLING & OTHER EE WAS USING A PRY BARY TO TURN THE WHEELS. EE'S FINGER GOT CAUGHT BETWEEN THE TIRE RIM & THE PRY BAR

EMPLOYEE WAS HITTING A BAR WITH A HAMMER AND MISSED. HE STRUCK HIS LEFT HAND, RESULTED IN LACERATION TO HIS LEFT HAND INDEX FINGER, REEQUIRED STITCHES.

EMPLOYEE WAS SHOVELING UP A PILE OF LIME AND SOME CAME OFF THE BACK OF THE SHOVEL AND ENTERED HIS RIGHT EYE. HE DID NOT REPORT THE INCIDENT TO HIS SUPERVISOR OR SEEK MEDICAL CARE UNTIL 09/23/9 9.

EE WAS CHANGING THE ACCUMULATOR CYLINDER. WHILE LIFTING CYLINDER FROM THE MACHINE, IT SLIPPED AND FELL ON EE'S RT SHOULDER AND RT WRIST.

EE WAS UNTIGHTENING THE NUTS ON THE BOLTS THAT HOLD THE HAMMERS IN PLACE ON THE DIXIE HAMMERMILL. HE WAS PUSHING ON THE PIPE WRENCH AND STRAINED HIS RIGHT GROIN.

EMP WAS CLEANING OUT THE DUST TRAILER, USING A SLEDGE HAMMER. TWISTED BODY RESULTING IN BACK PAIN.

EMPLOYEE WAS USING A COME-A-LONG TO PULL A HEAD SHAFT FORWARD AND THE CHAIN BROKE AND HE FELL TO THE FLOOR APPROX. 7'. HE BROKE FINGER ON RIGHT HAND AND FRACTURED PELVIS. DID NOT DISLOCATE.

EMPLOYEE WAS HELPING TO REMOVE A JAW CRUSHER FEEDER WING AND WAS REMOVING THE BOLTS HOLDING THE WING TO THE FEEDER. HE WAS INSIDE THE BUCKET OF 988B LOADER AND THE WING WAS NOT SECURED TO THE BUCKET. SEVERAL BOLTS WERE REMOVED AND THE REMAINING 2 BOLTS BROKE, ALLOWING THE WING TO FALL SEVERAL INCHES ONTO THE TOP OF THE BUCKET. THE EMPLOYEE WAS STRUCK ON HIS HEAD BY THE WING. SAFETY

EE WAS TURNING STEADMAN BARS OVAER TO BE READY FOR INSTALLING THEM. THE PRY BAR EE WAS SUING JAMMED BETWEEN TWO STEADMAN BARS WHEN ONE FELL ON THE OTHER THE PRY BAR CAME OUT STRIKING EE IN THE RIGHT HIP.

EMPLOYEE WAS UNPLUGGING ROCK JAMED IN A DRYER CHUTE WHEN THE ROCK CAME LOOSE THE BAR SLAMMED THE EMPLOYEE'S HAND AGAINST THE CHUTE. SMASHING HAND BETWEEN THE CHUTE AND THE BAR.

CUTTING CONVEYOR BELTING WHEN KNIFE SLIPPED AND CUT FINGER.

INJURED WAS ADJUSTING THE V-BELT DRIVE ON THE WARMAN CYCLONE PUMP WHEN THE WRENCH HE WAS USING SLIPPED OFF OF THE NUT. THE WRENCH IMPACTED HIS FINGER AGAINST THE PUMP AND INJURED HIS FOURTH F INGER OF HIS RIGHT HAND.

EMPLOYEE WAS FOLDING IN RADIAL STACKING CONVEYOR TO BE MOVED. USING A COME-ALONG TO ALIGN CONVEYOR IN IN BRACES. COME-ALONG HOOK SLIPPED OFF OF CONVEYOR STRIKING EMPLOYEE IN THE HEAD ABOVE RIG HT EYE CAUSING A 1 1/2" CUT.

I WAS SHOVELING OUT THE HOT SAND FROM THE DRYER PLENUM WHEN I SHOVELED SOME OF THE SAND TOO CLOSE TO MY BODY THE HEAT RISING FROM THE SAND BURNING MY LEFT ARM FROM THE WRIST TO THE ELBOW

HE WAS CHIPPING SLAG OFF OF A WELD WHEN A PIECE OF THE SLAG FLEW BEHIND HIS SAFETY GLASSES AND LODGED IN HIS RIGHT EYE.

EMPL WAS ATTEMPTING TO CLOSE DISCHARGE GATE ON EAST TANK WITH CHEATER BAR. GATE MOVED UNEXPECTEDLY & EMPL HIT HAND ON AUGER. HAND WAS XRAYED & SPLINT WAS APPLIED,

EMPLOYEE WAS CUTTING HAND RAIL PIPE AND A PIECE FLIPPED OVER AND STRUCK HIM IN THE NECK.

EMPLOYEE WAS CHANGING SCREENS IN PLANT, AND TIGHTENING SCREEN BOLTS WHEN THE WRENCH SLIPPED OUT OF HIS HANDS, MOVING HIS FOUR ARM OVER THE END OF A HOSE CLAMP. THE CUT IS ABOUT 2" LONG IN THE FRONT FACE FOREARM AREA.

REMOVING THE NUT ON HYDRAULIC CYLINDER HAD WRENCH ON NUT AND HITTING THE FLAT SPOT ON WRENCH WITH 6 POUND SLEDGE HAMMER MISSED SPOT ON WRENCH STRIKING HIS L FOOT ON ARCH ABOUT FROM STEEL TOE S.

I NAME WAS INSTALLING A PLASTIC LINING IN DUCT WORK FOR BIG DUCON HYE WAS CUTTING THE PLASTIC LINING WITH A UTILITY KNIFE I NAME REQUIRED FOUR STICHES TO HIS RIGHT HAND ON PALM BY FOREFINGER & THUMB

HE WAS TRIMMING SOME EDGES OFF A CONVEYOR BELT WITH A BELT KNIFE. HE SLIPPED THRU THE BELT AFTER MAKING A CUT AND STUCK HIMSELF IN THE RIGHT FOREARM. SMALL CUT THAT NEEDED 5 STITCHES.

IT IS ALLEGED THAT THE EMPLOYEE WAS USING A HAMMER TO BREAK FROZEN SAND FROM CONVEYOR AND DISCHARGE CHUTE. WHILE DOING THIS THE HAMMER SLIPPED TRAPPING THE EMPLOYEE HAND BETWEEN IT AND THE MET AL FLASHING.

ALLEGED THAT EMPL. WAS SHOVELING & CHIPPING SAND & ROCK OUT OF DRAIN GUTTERS. WHILE DOING THIS HE BRUISED HIS THUMB JOINT BY SHOVEL HITTING HIS THUMB.

IT IS ALLEGED THAT EMPL. WAS SPLICING CONVEYOR BELT & KNIFE SLIPPED & CUT HIS LEFT THUMB.

EMPLOYEE WAS TRYING TO LOOSEN WATER LINES AND IT BROKE LOOSE AND PIPE WRENCH HIT HIM ON SIDE OF HEAD