Buscar en el registro

EMPLOYEE WAS SCALING IN SETTLER. THE SCALE WAS HARD AND THE AREA DUSTY WHEN SCALE WAS CRUMBLING. DUE TO EMPLOYEE PRESPIRATION AND DUST CAUSED EYE BURN.

EMPLOYEE WAS SCALING THE CONE OF NO. 2 TRAY OUT OF A HIGH REACH. HE JAMMED HIS UPPER RIGHT ARM BETWEEN THE BASKET AND THE LEG OF THE TANK.

EMPL STATES THAT HE WAS USING BEATER BAR TO OPEN VALVE. WHEN HE WENT TO OPEN VALVE FINGER GOT CAUGHT BETWEEN BEATER BAR & VALVE.

EMPLOYEE WAS BREAKING A BOLT USING A HAMMER WRENCH.LEFT ARM ACCIDENTALLY TOUCHED A HOT STEAM PIPE.

EMPLOYEE WAS CUTTING NO. 9 CLOTH ON NO. 11 PRESS, KNIFE SLIPPED OUT OF CLOTH AND PUNCTURED TOP OF RIGHT KNEE.

EMPLOYEE WAS BEATING ON A PIN TO REMOVE LATERN RING FROM AN UNDERFLOW PUMP. PIN SLIPPED AND EMPLOYEE HIT HIS THUMB WITH THE MAUL.

EMPLOYEE ALONG WITH HIS WORKING PARTNER WERE LOWERING A BEAM FOR A TROLLEY. THE BEAM WAS BEING LOWERED TO THE FLOOR WITH A CHAIN FALL. THE BEAM BECAME UNHOOKED FROM THE CHAIN FALL AND FELL TO THE GROUND, STRIKING EMPLOYEE ON THE WAY DOWN.

EMPLOYEE WAS USING A 24" PIPE WRENCH WITH A CHEATER ABOUT 5 FT. LONG TO TIGHTEN A PACKING ON A BOOSTER PUMP. PUMP PACKING GLAND WAS CORRODED.

EMPL REMOVING TORQUE ELIMINATOR WRENCH WITH SOCKET FROM WORK PLATFORM.WHEN OTHER EMPL MOVED ELIMINATOR,SOCKET CAME OFF FELL 6' HITTING EMPL ON TOE.

EMPLOYEE WAS SWINGING A MAUL TO OPEN A VALVE. ONCE THE VALVE STARTED WORKING FREELY HE THEN TURNED IT WITH HIS HAND. SOME TIME LATER, HIS BACK STARTED HURTING.

EMPLOYEE WAS GETTING READY TO OPEN A VALVE. HE HIT IT WITH A MAUL, HOT CAUSTIC AND MUD BLEW OUT OF PACKING AND ;HIT HIM IN THE FACE.

WHILE BUILDING AN INSTRUMENT BOX, EMPLOYEE WAS BACKING UP A SCREW UNDER THE BASE PLATE. WRENCH SLIPPED LACERATING LEFT THUMB.

EMPL SWINGING 10 LB MAUL TO OPEN VALVE ON NO 2 SUCTION UNDERFLOW PUMP.MAUL MISSED KNOCKER ARM AND AS EMPL FOLLOWED THROUGH WITH SWING HE PULLED OR STRAINED LEFT SHOULDER JOINT.

OPERATOR WAS TIGHTENING A PACKING GLAND ON A STEAM PUMP CROSSHEAD.THE PACKING WRENCH SLIPPED CAUSING THE OPERATOR'S HAND TO HIT THE STEAM PUMP TIMING ARM.

WHILE USING A RACHET TO CLOSE DISCHARGE VALVE ON NO. 1 WASHER OVERFLOW PUMP, EMPLOYEE FELT A LIGHT PAIN IN HIS LOWER BACK. AS TIME PROGRESSED AND EMPLYEE STARTED WALKING, PAIN WORSENED. EMPL OYEE WAS PULLING DOWN ON RACHET.

EMPLOYEE WAS CLOSING VALVE ON #72 PRECIPITATION TANK HE JAMMED HIS RT HAND BETWEEN WRENCH AND PIPE

EMPLOYEE WAS WORKING TOP FLOOR OF FILLING TANK. TANK WAS FILLED PROPER LEVEL AND EMPLOYEE TRIED TO CLOSE FILL VALVE AUTOMATICALLY. THE VALVE WOULD NOT CLOSE AND THE TANK BEGAN TO RUN OVER. EMPLOYEE WENT FOR VALVE WRENCH AND ATTEMPTED TO CLOSE VALVE WHILE TANK WAS RUNNING OVER.

WHILE KNEELING AND CUTTING OFF STOCKING ON PRESS EMPLOYEE STUCK HIMSELF IN LEFT KNEE WITH KNIFE

WHILE REMOVING A 1 1/2" HOSE FROM TOP OF THE NO.2 SETTLER,EMPLOYEE USED A PIECE OF RUSTY ANGLE IRON TO LOOSEN HOSE FROM WATER OUTLET.WHILE HAMMERING PIECE OF RUST ENTERED EYE.

WHILE REMOVING ONE INCH IMPACT DRIVE FROM HIS LOCKER, HE STOOPED TO FIND A SCOKET AT THE BOTTOM OF HIS LOCKER. WHEN HE STARTED TO GET UP HE FLET A SHARP PAIN IN HIS BACK.

I NAME AND I NA4E WER ATTEMPTING TO UNPLUG THE EST BAUXITE SILT BY BEATING ON THE BEATER PLATE WITH A MAUL. BEATER PLATE BROKE AND FELL ABOUT 3 1/2 FT STRIKING I NAME ON THE TOE. BEATER PLATE WEIGH APPROX 6 5BS

WHILE TIEING UP3A BAUXITE SHIP ROPE GOT HOOKED ONTO A BUMPER PIPE LOCATED AT THE EAST END OF THE DOCK THIS BUMPER PIPE RUNS PERPENDICULAR OR N/S OF THE DOCK EMPLOYEE TRIED TO REMOVE THE ROPE A ND HAD TO STAND3IN AN AWKWARD POSITION TO DISLODGE THE ROPE THE POSITION HE WAS IN CAUSED HIM TO STRAIN HIS BACK

EMPLOYEES WERE 9EMOVING A 10 IN VALVE VALVE WAS BADLY SCALED INSIDE AFTER REMOVING THE BOLTS EMPLOYEE USED A WEDGE TO FREE VALVE VALVE WAS OFF BALANCE IN SLING AND WHEN VALVE BROKE LOOSE VALVE HANDLE HIT EMP5OYEE IN KNEE

AN OPERATOR WAS3DISCOUNNECTING A STEAM HOSE FROM A STEAM DROP. HE WAS STRIKING THE BOSS FITTING WITH A 12 LB MAUL TO LOOSEN THE FITTING. HE MISHIT THE FITTING AND STRUCK HIS FINGER ON THE FITT ING. THE INJURY3LATER BECAME INFECTED.

A PRECIPITATION3OPERATOR WAS REMOVING A STEAM RIG. THE EMPLOYEE WAS STANDING ON AN OPERATOR STAND USING A WRENCH TO LOOSEN BOLTS. IN THIS PROCESS, THE EMPLOYEE LOST HER BALANCE AND FELL BACKWA RDS APPROX. 5 F7 ONTO THE FLOOR BELOW.

OPERATOR WAS AT7EMPTING TO OPEN SLIDE GATE WITH A MAUL.WHULE STRIKING THE GATE,HE SUSTAINED AN UPPER BACK STRAIN.

EMPLOYEE WAS CL2SING A GATE VALVE USING A WRENCH WHILE USING THE WRENCH HIS RT ELBOW STRUCK A NEARBY RAILING

REMOVING 12 IN 5ONG PIVOT PIN FROM STEERING OF CLARK FRONT END LOADER WHILE REMOVING AS THE PIN CAME OUT IT STRUCK EMPLOYEES FOURTH FINGER LEFT HAND FINGER WAS CAUGHT BETWEEN THE PIN AND WOOD BLOCK SUPPORTI3G THE JACK

OPERATOR WAS IN3THE PROCESS OF OPENING A DRAIN BALVE USING A MAUL.WHEN THE OPERATOR STRUCK THE VALUE HANDLE,THE HANDLE BROKE.THE TWISTING MOTION CAUSED A LOWER BACK STRAIN.

EMP HAD POSITIO3ED THE TWO TON CAPACITY CHAIN FALL, 52 LBS, ABOVE TANK 22. WITH THE CHAIN FALL IN PLACE AND ATTACHED TO THE AIRLIFT, HE STARTED TO RAISE THE LIFT BY PULLING ON THE CHAIN FALL C HAIN. HE POSITI2NED HIMSELF WHERE HE COULD REACH UPWARD WITH BOTH HANDS AND PULL THE CHAIN BACK TOWARD HIS WAIST, IT BECAME HARDER TO RAISE ASS THE LIFT PROGRESSED

EMPLOYEE WENT T2 CLOSE A 650 POUND STEAM VALVE. HE AND HIS FELLOW WORKER WAS USING A 4 FEET WHEEL WRENCH. DUE TO RECENTLY INSTALLED NON-RETURN VALVE ALONG WITH AN AIR CYLINDER IN THIS SAME A REA, THERE WAS 5IMITED WORKING ROOM ON THE PLATFORM. IN ORDER TO CLOSE THIS VALVE, THE EMPLOYEE MUST PULL DOWN THEN PUSH. NORMALLY ONE WORKER CAN CLOSE VALVE.

WHILE GRINDING 4ETAL AT # 10 HEATER, PIECE OF METAL FLEW INTO EMPLOYEES EYE.

EMP WAS USING A3CHAIN FALL IN PRICIPITATION TO RAISE AN AIRLIFT. WHILE PULLING ON CHAIN FALL CHAIN. HE FELT PAIN IN HIS BACK

WHILE TAKING AN IMPELLAR OFF SAN CLASSIFIER PUMP HAD STRAIN ON SHEVE WITH CHAIN FALL, HOOK SLIPPED AND HIT EMPLOYEE WITH A GLANCING BLOW TO THE CHIN

WHILE CUTTING #2 ELECTRICAL WIRE WITH A HACKSAW THE SAW SLIPPED AND HIT THUMB CAUSING A DEEP CUT ON THE LEFT THUMB

I NAME STATED THAT HE WAS ATTEMPTING TO UNPLUG A STAB IN ON THE #3 CALCINE LINE WHILE DRIVING A REEMER THROUGH THE PLUGGED VALVE WITH A TEN POUND MAUL HE MISED WHILE STRIKING THE MAUL HANDLE AND PINCHED HIS FINGER BETWEEN IT AND THE REEMER HANDLE CAUSING THE INJURY

EMPLOYEE WAS MAKING REPAIR TO A GANTRY POWER CABLE. HE HAD TO USE HIS KNIFE TO CUT SOME INSULATION. THE KNIFE GOT SNAGGED ON A WINE, AS HE EXENTED MONO PRESSURE, THE KNIFE WENT INTO HIS FOREMA ARM.

EMPLOYEE WAS USING AN 18" PIPE WRENCH TO HOLD A VLAVE STEM STATIMANRY. WHEN THE AIR MOTOR WAS ACTIVATED, IT DROVE THE VALVE STEM CAUSING THE PIEP WRENCH TO ROTATES INTO THE AIR MOTOR & RACHET. EMPLOYEE LEFT HAND WAS CAUGHT BETWEEN THE TWO.

EMPLOYEE WAS CUTTING RUBBER BELTING WITH RAZOR KNIFE;KNIFE SLIPPED, CUTTING RIGHT THIGH.

EMPLOYEE WAS CUTTING METAL DEBRIS OUT OF SACK BINS;LACERATED RIGHT RING FINGER.

EMPLOYEE WAS REMOVING STEEL STRAPS FROM HEATER BUNDLE USING PLIERS. THE BAND BROKE AND CUT EMPLOYEES FOREARM.

EMPLOYEE WAS USING STEEL BAR TO UNPLUG CHUTE MOMENTARILY LET GO OF BAR DROPPED THRU CHUTE STRIKING RT HAND RESULTING IN FX OF RT RING FINGER

WHILE TRYING TO OPEN A VALVE THE WRENCH SLIPPED SMASHING FINGER BETWEEN PIPE AND WRENCH

EMP WAS ATTEMPTING TO OPEN HAMMER SLIDE GATE VALVE HE MASHED HIS FINGER BETWEEN MAUL HANDLE AND SUPPORT BEAM

RIGHT HAND CAUGHT BETWEEN WRENCH AND FILL LINE WHILE OPENING VALVE.

WHILE LOOSENING A COUPLING USING AN 8 LB MAUL, MAUL HIT TANK AND BOUNCED BACK STRIKING FOREHEAD.

EMPLOYEE ATEMPTED TO MOVE A SHAFT WITH A PRY BAR WHILE STANDING ON A PILE OF BELTING THE BAR SLIPPED CAUSING A PULLED MUSCLE IN SHOULDER.

EMPLOYEE WAS TIGHTENING A LUG NUT ON A GRAVELY MOWER WITH A WRENCH WHEN THE WRENCH SLIPPED AND HIT HIS RT MIDDLE FINGER

CHOKE VALVE WAS STUCK AND MAN USED A WRENCH TO CLOSE THE VALVE THE VALVE SWUNG CLOSED VERY QUICKLY AND JAMMED HIS FINGER BETWEEN THE WRENCH AND RAILING

WHILE TIGHTENING PACKING ON STEAM PUMP LEFT THUMB WAS JAMMED BETWEEN WRENCH AND CROSSHEAD ON STEAM PUMP CUTTING OFF TIP END OF LEFT THUMB