Buscar en el registro

Employee was using a pry-bar to dislodge a rock at the chute at CO5. The pry-bar slipped and smashed EE's little left finger between the pry-bar and another rock. After employee was evaluated by a physician it has been determined EE's finger is fractured.

Employee was attempting to bend light back out after it had been bent previously by someone else. Pipe wrench slipped and hit other hand that was on the boom injuring EE's finger.

installing bearing on c-7 conveyor metal entered eye causing laceration. released to work on light duty 1/22/21

EE wrote was pitching mud out of k-4 chute and rock rolled down and hit backside of hand and wrist. Doctor put EE on modified duty on 5/8/2019. EE is not to use right arm until follow up appointment.

Cutting new skirt rubber knife came off rubber cut right leg employee received three stitches was put on restricted duty for one week

Was holding up skirt board rubber while pulling a belt on when the pry bar came in contact with the tail pulley pinching finger between the pry bar and I beam. Employee was put on light duty or restricted duty.

Lining up truss on F-5-B with come a long when chain broke hitting EE right wrist. Physician performed procedures Laceration/wound repair at Dearborn county Hospital phone 8125378240

Employee wrote that they were cutting a belt with the utility knife when it slipped off of the belt and punctured leg. Employee went to St. Elizabeth Health care and received four stiches, returned back to work Monday when scheduled. No lost time occurred. Accident occurred at 9:10 pm employee started work at 2:00pm.

IW was cleaning pulley shaft in preparation of changing bearings/cum-a-long slipped off wing pulley pinching IW's middle and ring fingers against bearing support

While using a spud bar to clean out the syntron at Plant #1, the spud bar slipped causing the injured worker's left index finger to be pinched between the bar and the roof.

EE was working on the Telsmith #44 tightening bolts. Wrench slipped off the bolt causing him to fall into the belt guard and motor. He received a scraped shin and buttocks. He did not go to the doctor until 5/20/08.

Cutting a belt.

Employee was cutting a toggle bearing out and when he went to pry it off, it fell out and hit his left foot, behind his steel toe.

Employee was installing liners in M-2 Syntrons. The pry bar slipped and hit his upper lip and lacerated it.

EE was trying to unplug the crusher using a pry bar and hammer. While he was driving the bar into the material, he hit his index finger on his right hand. His finger was laid open.

Employee was cutting the belt off on M-17 conveyor and slipped. He hit his knee with the belt and slipped and cut his knee. Due to weather conditions, this was a factor in the injury.

Inj Employee and another employee, were replacing return rollers on m-23 converyor and while trying to break the bolt loose, the bolt broke, causing inj EE to ram his elbow against the trough roller assembly.

HE WAS CUTTING A PIECE OF SKIRT RUBBER AND THE KNIFE SLIPPED CUTTING HIS LEG.

He was working in a small electrical box and was stripping a wire and cut his left forearm.

Ee was attempting to pry loose bridged conglomerate from crusher opening. the bridged material came loose and caused the pry bar to hit him in the head.

INSTALLING V-BELT HAD A COME ALONG ON REDUCER TO PULL TURNBUCKLE BACK. COME A LONG CAME LOOSE, REDUCER TURNED AND HIT EE S TAILBONE.

EE WAS USING A COME-ALONG TO REMOVE A MOTOR FROM A SLURRY PUMP. WHILE PULLING ON THE COME-ALONG THE EYE RING IN THE MOTOR BROKE OFF CAUSING EE'S ARM TO HIT A HAND RAIL.

EE WAS PRYING THE COUNTERWEIGHT OFF OF THE FLOAT SIDE BEARING, THE PRY BAR SLIPPED & HIS HAND HIT THE CORNER OF THE COUNTERWEIGHT. IT TORE HIS SKIN.

EMPLOYEE WAS CLEANING MUD OUT OF THE PRIMARY CRUSHER'S FEEDER FLOOR UTILIZING A SHORT SPUD BAR AND A 10 LB SLEDGE HAMMER. HOLDING BAR WITH HIS LEFT HAND AND HOLDING THE HAMMER WITH HIS RIGHT HAND, EE WOULD STRIKE BAR WITH HAMMER TO DISLODGE MATERIAL. EE MISSED BAR WITH HAMMER HEAD AND INSTEAD PINCHED RIGHT INDEX FINGER BETWEEN END OFBAR AND HAMMER.

EE WAS CUTTING THE BELT & LOST HIS FOOTING, CAUSING HIM TO CUT HIS FINGER.

EE WAS USING A PORTAPOWER AND WHEN THE PRESSURE WENT UP HYDRAULIC FLUID LEAKED AND HIT EE IN THEEYES. (THE PRESSURE IN THE HYDRAULIC HOSES CAUSED THE FLUID TO SPRAY FROM OUT AROUND COUPLINGS).

EE WAS SWINGING A SLEDGE HAMMER, HITTING A BOARD TO INSTALL THE HOUSING. THE HAMMER KICKED BACK AND EE'S HAND HIT A PIN ON THE SHAKER.

EE WAS ATTEMPTING TO DISLODGE A ROCK FROM THE GRIZZLY, WITH A SLEDGE HAMMER, AND THE ROCK HIT HIM IN THE CHIN.

THE MEN WERE REMOVING A TAIL PULLEY, USING A PULLING BAR TO MOVE THE BELT BACK AND THE LUG BROKE. THE CHAIN AND LUG OFF OF THE BAR HIT INJURED IN THE FACE.

EE WAS HOOKING UP COMEALONG AND BENT HIS LITTLE FINGER BACK.

EE WAS USING A COME-A-LONG TO GET THE NORDBERG CRUSHER LOOSE. HE APPLIED PRESSURE TO THE COME-A-LONG AND IT STRIPPED. HE LOST HIS BALANCE AND FELL TO THE CRUSHER DECK FLOOR, HITTING HIS HEAD A ND ARM ON THE CRUSHER DECK HAND RAILING.

EE WAS USING A BREAKER BAR TO LOOSEN BOLTS ON CUTTING EDGES & HURT HIS LOWER BAKC

EMPLOYEE WAS CUTTING THE BELT TO MAKE A SPLICE ON M-6. HE CUT HIS FINGER.

HE WAS INSTALLING A NEW TORCH ON HOSES. THE WRENCH SLIPPED OFF THE HOSE NUT & STRUCK HIM UNDER HIS RIGHT EYE

HE WAS UNLOADING CHAINS & COMEALONG FROM 1 TRUCKTO ANOTHER. HE PULLED ON A CHAIN & COMEALONG WASHOOKED AND IT FELL ON HIS LEFT FOOT BEHIND THE STEEL TOE OF HIS BOOT

HE WAS INSTALLING BACK PLATE ON CHANGEOVER CHUTE. WHILE USING A COME-A-LONG TO PULL PLATE INTO PLACE THE PLATE GOT HUNG UP. ATTEMPTING TO FREE PLATE, HE PUT FINGERS BETWEEN PLATE AND PLATE MOU NTS. PRESSURE CAUSED PLATE OT POP INTO PLACE MASHING FINGER.

EMP WS USING A 5' PIPE AS A PRYBAR. HE LEANED IT AGAINST THE REAR TIRE OR THE TRUCK HE WAS WORKING ON. HE JACKED UP THE REAR OF THE TRUCK AND PIPE FELL ON HIS LEG.

HE WAS KNOCKING WEDGES LOOSE TO ADJUST THE CRUSHER DOWN 1 RIB. AS HE WAS SWINGING THE HAMMER, THE HANDLE GLANCED AND THE HAMMER HIT THE TOP OF HIS RIGHT FOOT. HE HAD STEEL TOE BOOTS ON, BUT TH E HAMMER HIT BEHIND THE STEEL TOE. CRUSHER HAD ALOT OF MATERIAL BUILT UP AROUND IT AND LIMITED THE SPACE TO STAND.

HE WAS CHANGING THE TAIL PULLEY ON F-1B. WHILE PUTTING THE PULLEY BACK IN THE CONVEYOR, THE COME-A-LONG SLIPPED AND THE PULLEY HIT THE SIDE OF HIS LEG.

HE WAS FREEING TRA'S ON THE TAIL OF M-55. HE WASUSING A 4 LB. HAMMER AND WHEN HE WENT TO HIT AT A ROLLER, HE MISSED AND HIS HAND WENT BETWEEN THE ROLLER AND THE BELT.

HE WAS REMOVING A SPRAY NOZZLE FROM A SPRAY BAR & THE WRENCH SLIPPED & HE HIT HIS RIGHT HAND ON ANOTHER SPRAY BAR NOZZLE.

HE WAS BREAKING PIPE UNION APART WITH A PIPE WRENCH.

EMPLOYEE WAS IN SHOP WORKING BETWEEN TANDEM WHEELS OF STOCK TRUCK BENT OVER IN AN AWKWARD POSITION AND INJURED HIS BACK TIGHTENING BOLTS ON FRAME.

HE WAS HAMMERING IN SLIDES ON SAND GATES IN M-23 TUNNEL.

HE WAS STRIPPING COATING OFF OF A FLEX CONDUIT WITH A UTILITY KNIFE & THE KNIFE SLIPPED & CUT HIS RT INDEX FINGER

HE WAS USING A 1 1/2 TON COME ALONG TO PULL A CONVEYOR BELT TOGETHER SO THAT IT COULD BE SPLICED . HE WAS APPROXIMATELY 15 FT FROM THE GROUND WHEN THE COME ALONG EITHER SLIPPED OR FAILED TO WORK PROPERLY CAUSING HIM TO LOOSE HIS BALANCE AND FELL.

HE WAS HELPING TO CHANGE THE DRIVE SIDE ECCENTRIC BEARING. HE WAS SWINGING THE HAMME (SLEDGE) HORIZONTALLY TO DRIVE THE HOUSING BACK IN PLACE. HE FELT A POP IN HIS MIDDLE BACK.

EMPLOYEE WAS USING A 2" WRENCH TO HIT SKIRTING ON #4 TAIL PULLEY TO LINE UP BELT. WRENCH CAME BACK AND HIT EMPLOYEE, CUTTING HIS RIGHT INDEX FINGER.

HE WAS RELINING THE CHUTE TO M-5. HE WAS WORKING THE COME ALONG TO PULL THE LINER IN PLACE. HE PUT PRESSURE ON THE COME ALONG AND THE HANDLE SLIPPED AND HIT THE TOP OF HIS HAND.

HE WAS SPLICING ON M-67 CONVEYOR. AS HE WAS SQUARING THE BELT, HIS KNIFE CUT HIS THUMB.