Buscar en el registro

Employee was using a pry bar to dislodge broken plow tips in RMI. They felt the job was strenuous but was alright when they completed it. They had a prescheduled day off 10/28/24 and returned to work on 10/29/24. Their back was stiff and mentioned it to the Maint. Coordinator. By 10:00 AM their back had a spasm, and they could hardly walk.

Employee was cutting a piece of metal with an electric grinder when the cutting disk bound up causing the grinder to kick back and cut the top of their hand.

Employee was working on mill reassembly. Noticed a pain in EE's back. Reported four days later when it did not improve.

Individual was attempting to loosen a screw conveyor, while going through equipment checkout. procedure was to pull towards them with the pipe wrench. The screw would not loosen, subject attempted to move it in the opposite direction. The pipe wrench slipped off and individual fell forward injuring his arm with a minor laceration.

Employee fractured tip of left thumb, struck with hammer

While loosening a bolt, the wrench slipped and employee cut/bruised back of right hand

While cutting banding from a pallet of bags using a utility knife, the worker slipped and cut his left index finger.

While loosening a bolt using a breaker bar employee felt pain in his lower left rib. The pain continued and he sought medical assessment and received a work restriction of "light duty-limited lifting".

Four people were rebuilding the motor on the Deister. They used two come alongs to move the motor out of a confined area into an open area. One of the come alongs did not have its safety latches. This caused the come along to slip out of the motor's lifting eye and caused the motor to swing into the employee's knee. Employee was confined to desk work.

Employee was on the 1st floor PX 7000D mill. He was on a boom lift replacing the structural bolts by using a torque wrench to tighten them up. When he was tightening the first bolt the wrench fell off the bolt while he was pushing down causing his hand to be in the middle of the concrete block and the wrench.

Cut palm of left hand with utility knife while trying to cut rope.

Strained right elbow while shovelling wet product

Employee was swinging a hammer to loosen material & struck a flange with his hand, resulting in a pinch/laceration requiring sutures.

Employee was torquing terciary crusher liner segment bolts with a hydraulic torque wrench. When the wrench was operated it slipped and squeezed his right hand's index and middle finger against the wall of the crusher.

Employee and one other were using a bar to lift a ~150lb object. Felt pain in his back 3 days later & then went to a chiropractor on his own.

Employee was cutting a hose from Darbed fitting water running down everything. Knife slipped & employee lacerated the palm of left hand. 4 stitches required.

EE WAS DISMANTLING COWLES MIXER BLADE FROM A SHAFT. EE WAS USING A WRENCH AND SOCKET WITH RATCHET THAT WERE NOT THE CORRECT SIZE FOR THE JOB. THE BOLT CAME LOOSE, EE'S HAND SLIPPED AND HIT THE BLADE.

While employee was standing on a piece of dewatering equipment trying to free a bound rotating assembly with a bar, the bar slipped and employee lost his balance, fell and broke a bone in his leg.

EMPLOYEE WAS USING A PRY BAR TO DISLODGE ROCK IN A DIVERTER AND THE SLIDE GATE CAME DOWN ON HIS RIGHT WRIST. EMPLOYEE FAILED TO DE-ENERGIZE THE EQUIPMENT AN VIOLATED THE COMPANY LOCKOUT/TAGOUT POLICY AND PROCEDURES. HE WAS PLACED ON MODIFIED WORK.

CUT HAND WITH KNIFE WHILE CUTTING BULK BAG CONTAINING WASTE PRODUCT.

EE ALLEGES HE INJURED HIS BACK AT WORK WHILE WORKING ON A ROTARY ASSEMBLY. HE DID NOT REPORT THIS TO THE COMPANY UNTIL 12/16/03 AFTER HE WENT TO HIS OWN PHYSICIAN. CLAIM IS BEING QUESTIONED SINCE HE DID NOT REPORT UNTIL ONE WEEK LATER AND AFTER HE WENT HUNTING ON HIS OWN TIME. SEE ATTACHED NOTE. HE IS ON MODIFIED WORK.

EE WAS LOOSING A PLUG ON A GEAR BOX WHEN HIS HAND SLIPPED OFF OF HIS WRENCH AND HIS LEFT ELBOW STRUCK THE EDGE OF A BELT GUARD ON CONVEYOR 40117. MEDICAL TREATMENT WAS NOT REQUIRED UNTIL 10-2 3-03, AT WHICH TIME IT BECAME REPORTABLE. EE WASPLACED ON MODIFIED WORK.

EE WAS CUTTING A BAND ON A CARTON OF PAPER. WHEN BAND BROKE, KNIFE SLIPPED AND STRUCK OTHER ARM.

EMPLOYEE CLOCKED IN AND WAS CLEANING HIS POCKET KNIFE. HE ALLEGES HIS HAND SLIPPED AND HE LACERATED HIS RIGHT INDEX FINGER, WHICH REQUIRED 10 STITCHES. CLEANING HIS OWN PERSONAL POCKET KNIFE I S NOT ONE OF HIS ASSIGNED WORK DUTIES.

EE WAS LOOSENING A CONVEYOR TAIL PULLEY WHEN THE ADJUSTING NUT CAME LOOSE AND THE EMPLOYEE'S HAND SLIPPED, STRIKING THE BACK OF HIS FOREARM ONTO THE CONVEYOR FRAMEWORK.

EE WAS USING A STEEL BAR TO DISLODGE ROCKS AT THE TRANSFER POINT OF CONVEYOR 103. EE HIT HER HAND ON THE INSIDE OF THE STEEL ROCK BOX.

EE WAS TIGHTENING FLANGE AND CUT HAND ON SHARP OBJECT.

HE WAS INSTALLING IMPELLER ON 3K WILLFLEY PUMP & WRENCH SLIPPED & HIS HAND HIT THREADED ROD ON PUMP Y

EE HOOKED TWO CHAIN HOISTS TOGETHER TO PULL A HOPPER LINER INTO PLACE. THE HOOK ON ONE OF THE VCHAIN HOISTS SPREAD OPEN, RELEASING IT FROM THE OTHER CHAIN HOIST, AND HIT THE EE ON THE RIGHT LE G.

EE WAS MOVING A METAL CHUTE AND THE CHUTE POPPEDFREE & COMEALONG HIT EE IN THE FACE. EE RECD A BROKEN NOSE & 2 BLACK EYES

EMPLOYEE WAS CUTTING IN BAGS TO BRING BUL BAGGER UP OT CORRECT WEIGHT. EMPLOYEE CUT HIMSELF WITH A UTILITY KNIFE.

EE WAS PULLING A JACK OFF OF A JACK STAND, IT TIPPED, AND SMASHED THE MIDDLE FINGER OF HIS LEFT HAND

WHILE CHANGING A WATERLINE, STEPPED ON PIPE WRENCH TO OPEN VALVE, FELT SOMETHING "POP" IN CALF MUSCLE.

DURING THE REMOVAL OF TOP HATCH BOLTS ON A RR CAR, A BOLT WAS TOO TIGHT TO REMOVE BY HAND, EE THEN KICKED THE WRENCH WITH HIS FOOT, TRYING TO LOOSEN THE BOLT. A GLANCING BLOW RESULTED, BRUISIN G HIS HEEL. THE DR CALLED THE INJURY A FOOT HEEL CONTUSION. AFTER AN INJURY INVESTIGATION, IT WAS IDENTIFIED AN AIR ... MUST BE USED TO REMOVE THE BOLTS.

UPON FINAL FOLLOW UP, EE INFORMED ME THAT HE HAD STICHES IN THE TIP OF HIS FINGER WHICH HE CUT TWITHA DULL UTILITY KNIFE BLADE. HE WAS HACKING AT A PIECE OF PLASTIC STRIP WHEN HIS HAND SLIPPED .

EE WAS ATTEMPTING TO DISLODGE 50 LBS BAGS OF CALCIUM CARBONATE OUT OF A CHUTE. HE WAS USING A SCRAPER TOOL AND ONE OF THE BAGS FELL ON THE HANDLE CAUSING THE SCRAPER PORTION OF THE TOOL TO BOU NCE UP AND HIT HIM IN THE FACE.

SPLITTED L.S. STRAIN OF LEFT LITTLE FINGER.

EMP WAS TRYING TO UNLATCH A HOPPER WITH A BAR AND AS HE PUSHED UPWARD, HE HEARD HIS LEFT WRIST POP.

EMPS WERE WORKING/HAMMERING ON A METAL SHAFT. METAL WAS BRITTLE AND A PIECE BROKE OFF AND EMBEDDED IN EMPS FOREHEAD.

EMP WAS STANDING BENEATH AN 85 TON TEREX HAUL TRUCK. HE HAD HIS KNEES BENT SO HE COULD LOOK AT THE ENGINE. TWISTED TO GRAB TOOL AND HEARD HIS KNEE POP.

EMPLOYEE WAS SECURING A FRAME HOUSING TO A HAULAGE TRUCK WITH A CHAIN BINDER. THE HANDLE OF THE CHAIN BINDER SLIPPED AND HIT EMPLOYEE'S FACE. THE BLOW TO THE EMPLOYEE'S HEAD AREA KNOCKED HIM OUT. THERE WERE NO FACIAL, HEAD, OR NECK FRACTURES. EMPLOYEE SUSTAINED A LACERATION TO THECHIN AREA AND ONE BROKEN TOOTH AND TWO CHIPPED TEETH.

EE WAS CHANGING TEETH ON A LOADER. THE LOADER BUCKET WAS RAISED APPROX. 31/2 TO 4 FEET HIGH. EE PLACED THE REPLACEMENT TEETH ON BUCKET AND AS HE WAS HAMMERING ONE OF THE PINS IN A TOOTH, ANOTH ER ONE FELL OFF AND ONTO HIS LEFT FOOT. EE WAS WEARING STEEL TOE BOOTS. FOOT WAS INJURED ABOVE THE STEEL SECTION.

WHILE REBUILDING A KEYSTONE VALVE- DRIVING OUT PIVOT PIN HAMMER SLIPPED OFF PIN- STRUCK EMPLOYEE IN LEFT LEFT HAND.

TIGHTENING BAG SPOOL W/ALLEN WRENCH AND THUMB POOPPED OUTOF JOINT.

EMPLOYEE WAS KNEELING ON GROUND, PLACED A 24" PIPE WRENCH ON A FITTING ON AN ANTI-FREEZE PUMP AND BEFORE HE ATTEMPTED TO LOOSEN THE FITTING, HE HAD A MUSCLE SPASM IN HIS BACK AND FELT A SHARP PAIN.

EMPLOYEE WAS TRYING TO FREE UP A 45B DISCHARGE PUMP USING A PIEP WRENCH AND PIPE EXTENTION.

EMPLOYEE WAS REMOVING INSIDE ROLLER BEARING RACE FROM SHAFT, TAPPING ON IT WITH A HAMMER, SMALL PIECE OF BEARING CHIPPED OFF AND STUCK INTO INSIDE OF LEFT LEG.

46595G SAW W/PRY BAR CHAIN SAW CONTARI AND PRY BAR.

THE EMPLOYEE WAS UNPLUGGING THE CENTRIFUGE, CONSISTING OF TURNING THE LOCKED UP SCREWS BY HAND WITH A PIPE WRENCH UNTIL FREE. EE SAYS THIS TOOK FROM 3:30 PM UNITIL 6 PM CONTINUOUSLY, AS HE COU LD STOP ONCE STARTED OR THE SLURRY IN THE SCREW WOULD HARDEN AGAIN.

MOVING TOO MUCH WT HURT BACK