Buscar en el registro

EE and a coworker were using a pry bar to dislodge some rocks, slipped, and EE's finger (ring finger on left hand) got smashed in between the pry bar and a metal door. EE applied first aid and returned to work. Went in after work and received 5 stitches.

Replacing bearing on tail pulley of primary crusher. Driving bearing into place when piece of metal broke off and struck employee just above upper lip causing laceration which required two sutures.

Employee was removing lug nugs on stockpile truck tire using breaker bar with etension. Lug nut broke loose suddenly, causing sudden shock to wrist area, resulting in swelling and pain in Left Wrist.

Shoveling hopper out when hand slipped off shovel handle and stuck side of bin, causing pain and bruising in right fifth (pinky) finger. Examination showed no breaks but finger was splinted to protect finger.

Employee was using utility knife to cut rubber hose in order to install new fitting on end of hose. In process of cutting hose, utility knife slipped, causing laceration/puncture wound approximately 1" long on the inside of right thigh about 2"-4" above knee. Wound required 5 stitches.

While tightening the motor mount on crusher, the wrench slipped and employee fell back into belt guard which fell over onto top of left foot.

Employee was helping replace a conveyor belt when the vise grips attached to the conveyor belt EE was pulling on came off of the belt causing EE to fall to the ground on some rocks.

Tightening a bolt on the tailgate of Caterpillar 771D. Pulling down with a wrench he heard something pop in his right shoulder.

Changing bucket tooth on Caterpillar 988F. After removing the pin that holds the tooth, he hit the edge of the tooth with a hammer to loosen the tooth from the adapter when a piece of metal chipped off. The piece of metal struck the right inner thigh of his right leg.

He was putting a hole in plastic with knife, knife didn't lock and cut 2 cm laceration in right index finger.

WHILE PRYING WITH A METAL BAR ON A ROLLER. THE BAR SNAPPED BACK AND HIT HIM IN THE NOSE.

INSTALLING A BEARING IN A ROLLER. HAMMERING THE BEARING IN WITH A PIECE OF SHAFT WHEN HE MISSED AND HIT HIS FINGER.

CUTTING A CONVEYOR BELT WITH A MULTI-USE KNIFE AND THE KNIFE BLADE FOLDED UPON HIS FINGER.

WAS SWINGING A PICK AXE TO CLEAN MUD OUT OF FEEDER FLOOR & TWISTED HIS BACK WHICH RESULTED IN HIM PULLING SOME LOWER BACK MUSCLES

VICTIM WAS TRYING TO DRIVE A PIN WITH A HAMMER. THE PIN SHIFTED AND IT STRUCK HIS RIGHT THUMB TIP, SMASHING IT.

LOOSENING SCREW JACK BY PUSHING AGAINST A BAR WITH HAND AND RIGHT SIDE OF CHEST WHEN FELT SOMETHING POP.

EMPLOYEE WAS USING A BAR TO OPEN A COVER DOOR ON THE ROLL CRUSHER. THE BAR SLIPPED AND THE EMPLOYEE LOST HIS BALANCE AND FELL INTO A CORNER OF A GUARD ONT HE CRUSHER, WHICH BRUISED HIS LEFT R IBS.

TRIMMING A PIECE OF SKIRT RIBBER WITH A KNIFE INSIDE THE HOPPER BENEATH THE SCREEN ON THE SECONDARY CRUSHER. THE KNIFE SLIPPED AND CUT THE TISSUE ABOVE THE RIGHT KNEE.

WHILE USING A BREAKER BAR ON A PIPE WRENCH. THE JAWS OF THE PIPE WRENCH SLIPPED THE BREAKER BAR HIT THE VICTIM IN THE HARD HAT WHICH THEN HIT HIS HEAD. THE HARD HAT CUT A GASH IN HIS FOREHEAD ABOVE HIS EYE. THIS REQUIRED STICHES TO CLOSE.

WRENCH BEING USED TO LOOSEN NUT.PIPE EXTENSION USED TO GET MORE LEVERAGE.ADAPTER N WRENCH BROKE AND HE FELL TO GROUND 3\ FALLING ON UPPER BACK.