Buscar en el registro

EMPLOYEE WAS REMOVING A BROKEN HOSE FROM A PRESSURE WASHER. HE WAS PULLING ON TWO WRENCHES WHEN THE HOSE CAME LOOSE. AT THAT TIME THE EMPLOYEE HEARD A POP AND FELT PAIN IN HIS LEFT SHOULDER.

EE WAS TIGHTENING THE 01 TUBE ON THE OUTSIDE OF THE PUMP SHAFT. THE PIPE WRENCH SLIPPED OFF THE PIPE, CAUSIN GHIM TO FALL TO THE GROUND HITTING HIS RIGHT KNEE ON THE PIPE CASING. THIS RESULT ED IN STITCHES.

EMPLOYEE WAS PUSHING SLAG WITH A SHOVEL INTO THE SLAG BIN WHEN HE FELT A STRAIN IN HIS LOWER BACK. HE DID NOT SEEK MEDICAL ATTENTION AT THE TIME OF THE INCIDENT.

INJURED WAS CLEANING THE LIME SLAKER FEED CHUTE WITH A BAR. THE BAR CAME INTO CONTACT WITH THE SLAKER PADDLE WHEEL, AND PINNED HIS FINGER TO THE CHUTE.

EMPLOYEE STATES THAT AS HE WAS CUTTING OPEN A FILTER USING A KNIFE, HIS HAND SLIPPED AND HIS LEFT INDEX FINGER WAS CUT BY THE FILTERS EDGE. THE EMPLOYEE WAS TRANSPORTED TO THE ER WHERE 8 SUTUR ES WERE PLACED IN THE FINGER. HE WAS RELEASED TO RETURN TO WORK FULL DUTY.

EE STATED THAT AS HE AND ANOTHER EE WRE CHANGINGTHE TEETH ON THE S110 SHOVEL, HE SWUNG THE SLEDGE HAMMER ONTO ONE OF THE TEETH, WHEN A PIECE OF METAL FROM THE PIN HAMMER FLEW UP AND HIS UPPER LIP. HE WENT TO THE ER WHERE THE PIECE OF METAL WAS REMOVED FROM HIS LIP AND A TETANUS SHOT WAS GIVEN. HE WAS RELEASED TO RETURN TO WORK FULL DUTY.

EMPLOYEE WAS CHANGING THE LINER IN THE 20" KREBSCYCLONE. HE WAS USING A KNIFE TO CUT AWAY THE RUBBER LINER. THE KNIFE SLIPPED AND LACERATED THE TOP 1/8" OFF THE RIGHT THUMB. HE WAS TRANSPORTED TO THE ER WHERE A SHIN-GRAPH WAS DONE. HE WAS RELEASED TO RETURN TO WORK LIGHT DUTY.

EMPLOYEE WAS REMOVING PUMP BASE BOLTS TO REMOVE A PUMP. WHILE LOOSENING THE NUT, THE BOLT STUD BROKE CAUSING THE EMPLOYEE TO LOSE HIS BALANCE. THE SUDDEN MOVEMENT CAUSED A STRAIN TO LOWER BACK .

EMPLOYEE WAS TORQUING BOLTS ON A SPINDLE USING A 4 FOOT RATCHET WHEN HIS SHOLDER POPPED. IT BEGAN TO BURN AND A KNOT DEVELOPED ON TOP. HE WAS TAKEN TO TOWN WHERE A DR. DIAGNOSED HIM WITH A RIG HT SHOULDER AC JOINT SEPARATION. THE ARM WAS PLACED IN A SLING WAS RELEASED TO RETURN TO WORK ON LIGHT DUTY.

EMPLOYEE WAS PUSHING ON A 1/2" DRIVE RATCHET TO BREAK LOSE A BELT. HE FELT A POP IN HIS RIGHT SHOULDER. AFTER COMPLETING JOB. HE WAS UNABLE TO RAISE THE ARM AND WAS TAKEN FOR X-RAYS. HE WAS DI AGNOSED WITH A MUSCLE STRAIN. HE HAD A FOLLOW-UPON 2/13 AND WAS RELEASED TO RETURN TO WORK LIGHTDUTY.

EMPLOYEE WAS PULLING AN ELECTRIC SHOVEL CABLE ONTO A BERM USING HOT STICKS. THE HOT STICK SLIPPED OFF THE WET CABLE. THIS CAUSED THE EMPLOYEE TO LOSE HIS BALANCE AND FALL OFF THE HIGHWALL, APP ROX. 3O'. HE WAS TAKEN TO HGH AND ADMITTED TO THE HOSPITAL. HE WAS DISCHARGED TO GO HOME FROM THE HOSPITAL ON 2/5 AND RELEASED TO RETURN TO WORK LIGHT DUTY ON 2/9/98.

EE WAS ATTEMTPING TO CUP OPEN A RESPIRATOR CARTRIDGE USING A UTILITY KNIFE. THE KNIFE SLIPPED IN HIS HAND, CUTTING HIS LEFT INDEX FINGER. HE WASTAKEN TO THE ER AND GIVEN A TETANUS SHOT. SIX SU TURES WERE USED TO CLOSE THE LACERATION. EE WAS RELEASED TO RETURN TO WORK FULL DUTY.

MILK-O-LIME TRUCK HAD AN AIR PRESSURE LEAK ON THE INNER RIGHT HEAD SPRAY VALVE. THE OPERATOR TURNED ON THE MAIN PUMP FOR EMPLOYEE TO CHECK. WHEN EE REMOVED THE LAST BOLT FROM THE SPRAY VALVE, THE TOP HALF OF THE VALVE BLEW OFF FROM THE PRESSURE CREATED FROM THE FULL TANK OF LIME BY PASSING THRU MAIN PUMP. EE HIT WITH LIME ON HIS UPPER BODY AND FACE, RESULTING IN BURN TO RIGHT EYE.

EE WAS SHARPENING A WOODEN STAKE TO USE AS A DETONATION CORD HOLDER. THE KNIFE SLIPPED, CUTTING HIS LEFT INDEX FINGER. 5 SUTURES WERE NEEDED TO CLOSE THE LACERATION. EE WAS RELEASED TOW ORK ON RESTRICTED DUTY UNTIL THE SUTURES ARE REMOVED

EE WAS REMOVING A BOLT FROM A CLAMP WITH A RACHET WRENCH. THE BOLT WAS RUSTED & VERY HARD TO BREAK LOOSE. AS HE PUSHED FORWARD WITH FORCE ON THE RACHET, THE BOLT BROKE & HIS HAND MOVED FORWARD VERY QUICKLY HITTING IT ON A PIECE OF METAL CUTTING IT ON HIS RIGHT INDEX FINGER.

CREW WAS INSTALLING A PUMP. A CLAMP HOLDING THE OIL TUBE SLIPPED, THE TUBE FELL AND PINCHED EMPLOYEE'S FINGER.

WHILE TRYING TO OPEN VALVE TO KILN SCREEN, THE HANDLE SLIPPED OUT OF THE ADAPTER THAT HOLDS IT IN PLACE. THIS RECEIVED FOUR SUTURES. EE WAS RELEASED TO FULL DUTY AND WILL HAVE THE SUTURES REMO VED IN TWO WEEKS.

THE WRENCH EE WA PULLING ON SLIPPED OFF THE BOLT. THIS CAUSED HIM TO HIT HIS RIGHT ELBOW ON THE PULL DOWN CHAIN OF DRILL 304. HE WA SEEN BY A PHYSICIAN ON 7-22-97 WHO DRAINED THE ARA WHICH W AS SWOLE. HE WAS DIAGNOSED WITH TRAUMATIC ELBOW EFFUSION.

EE WAS CHANGING THE RIPPER POINTS ON DZ256. ANOTHER EE HELD THE PIN DRIVER WHILE EE HAMMERED IT. AS HE SWUNG THE HAMMER AND HIT THE PIN DRIVER, A SLIVER CAME OFF OF THE PIN DRIVER. THE SLIVER BECAME EMBEDDED IN HIS UPPER LEFT CHEST IN THE UNDERARM REGION.

THE EE WAS WORKING WITH STEEL BANDING MATERIAL APPROX. 20'LONG AND 2" WIDE. WHILE CUTTING THE MATERIAL WITH TIN SNIPS, AN END SPRANG LOOSE, AND CUT THE BACK OF HIS RIGHT HAND AT THE BASE OF HI S THUMB.

ADJUSTABLE WRENCH SLIPPED OFF BOLT HE WAS LOOSENING CAUSING HIM TO LOSE BALANCE & FALL ON HIS KNEES, DID NOT SEEK MEDICAL ATTENTION UNTIL 12-5-96 DIAGNOSED AS MUSCLE STRAIN OF LOWER BACK.

EMPLOYEE WAS TIGHTENING BOLTS ON 14" OVERHEAD VALVE. WRENCH SLIPPED AND STRUCK HIM ON FACE AND TEETH RESULTING IN CHIPPED TOOTH AN DNASAL CONTUSION.

EE WAS USING A 3/4" RACHET WITH A 1 1/2" SOCKET TO BREAK LOOSE THE DRAIN PLUG ON THE LEFT FRONT WHEEL BEARING DRAIN. THE WRENCH SLIPPED AND SMASHED EE'S LEFT LITTLE FINGER BETWEEN THE RATCHET HANDLE AND THE RIM. EE WAS DIAGNOSED WITH AN AVULSION AND FRACTURE INJURY AND PLACED ON RESTRICTED WORK DUTY UNTIL REEVALUATED BY DR.

EE WAS USING A PUNCH TO REMOVE A BROKEN BELLY PAN BOLT. AS HE STRUCK PUNCH W/ HAMMER, A SMALL PIECE OF METAL CAME OFF & LODGED IN HIS RIGHT PINKY FINGER. ATTEMPTS TO REMOVE METAL BY ER PHYSICI AN WERE UNSUCCESSFUL. HE THEN SUTURED & BANDAGEDTHE WOUND AND RELEASED THE EE TO REGULAR DUTY.

EE WAS ATTEMPTING TO CUT A 3" PLASTIC HOSE WITH A UTILITY KNIFE. WHEN HE APPLIED PRESSURE TO THE KNIFE IT SLIPPED OFF THE HOSE AND CUT INTO HIS RIGHT HAND. LACERATION REQUIRED 9 SUTURES.

WHILE CUTTING A PIECE OF ROPE WITH A HACKSAW THEBLADE SLIPPED AND CUT LEFT HAND.

EMP WAS ASSISTING IN ASSEMBLING A SNUB PULLEY. TOOLS BEING USED WERE A 1" DRIVE TORQUE WRENCH AND A 3/4" TO 1/2" REDUCER. ON THE SECOND PULL THEREDUCER BROKE CAUSING EMP TO FALL, HURTING HIS L EFT ANKLE. EMP WAS RELEASED TO FULL DUTY, BUT AFTER FURTHER EVALUATION WAS PUT ON RESTRICTED DUTY 7-29-96.

THE EE WAS UNSCREWING THE LAST NUT ON THE LINER MILL LINER IN ORDER TO REMOVE IT. THE BALL LIFTER SHIFTED AND CAUGHT HIS LEFT INDEX FINGER BETWEEN THE HULL AND THE NUT, CRUSHING IT. HE WAS TAK EN TO HUMBOLDT GENERAL ER, WHERE HE WAS TREATED AND PLACED ON LIGHT DUTY.

THE EE WAS CLOSING THE VALVE ON 9 CYCLONE WHEN THE WRENCH SLIPPED OFF THE HANDLE. THE WRENCH CRUSHED HIS RIGHT INDEX FINGER AGAINST ANOTHER VALVE HANDLE. HE WAS TAKEN TO HUMBOLDT GENERAL ER, W HERE HE WAS TREATED FOR A TUFT FRACTURE OF THE IINDEX FINGER AND WAS PLACED ON LIGHT DUTY.

A NEW DIVERTER PLATE IN THE SAG MILL FEED CHUTE CAUSED THE CHUTE TO PLUG. EMP HAD TO ENTER THE CHUTE IN ORDER TO UNPLUG IT. WAS PULLING ON SOME ROCKS & WHEN THEY CAME LOOSE HE FELL BACKWARDS, HITTING HIS KNEE WITH THE BAR AND THEN TWISTING IT. WAS TAKEN TO HUMBOLDT GENERAL ER, WHERE HE WAS TREATED AND PLACED ON LIGHT DUTY.

TIGHTENING COMPRESSOR BOLTS USING A 2 3/4 COMBINATION HAND HELD WRENCH. EMPLOYEE EXPERIENCED PAIN IN UPPER RIGHT SHOULDER RESULTING IN DIAGNOSEDBACK STRAIN.

THE EE LOADED HIS WATER TRUCK 216 AT THE W 10 STAND PIPE AND WAS PLACING A SHOVEL AT THAT LOCATION TO SUE AS A GUIDE WHEN HE RETURNED FOR HIS NEXT LOAD. HE TWISTED HIS ANKLE AND WAS TAKEN TO H UMBOLDT GENERAL ER FOR TREATMENT. DR DETERMINED THAT HE HAD A SPRAINED ANKLE AND PLACE HIM ON LIGHT DUTY.

EE WAS HOLDING TWO SHOVELS, ANOTHER EMPLOYEE GRABBED ONE OF THE SHOVELS, AND THE TWO MEN BEGAN STRUGGLING OVE IT. EVENTALLY, THE SECOND EMPLOYEE LET GO OF THE SHOVEL AND BEGAN HITTING EE, KNO CKING HIM TO THE GROUND AND CONTIUING TO HIT HIM UNTIL HE WAS PULLED OFF BY A THIRD EMPLOYEE.

EMPLLYEE WAS ATTEMPTING TO CUT A PLASTIC BAG WITH A UTILITY KNIFE. DURING THIS PROCESS, HE CUT THE PALM OF HIS HAND. EMPLOYEE IS PERFORMING ALL OF HIS JOB DUTIES.

EE WAS SHOVELING DIRT FROM THE HOPPER IN THE JUNIPER LAB. THE SHOVEL HIT THE TOP OF THE CONTAINMENT ARE AND CAUSED HER TO TWIST HER RIGHT WRIST. SHE WAS TAKEN TO ER, WHERE IT WAS DETERMINED TH AT SHE HAD A HAIRLINE FRACTURE IN HER RIGHT WRIST.

REMOVING 1ST STAGE VALUTE ON MAIN AIR COMPRESSOR USING LARGE BOX END WRENCH. WAS PUSHING UPWARDS TO FREE A BOLT. WHEN BOLT BROKE FREE, RIGHT THUMB WAS PINCHED BETWEEN WRENCH AND MACHINE CASING FRACTURING THUMB.

EE WAS IN THE PROCESS OF POUNDING IN A WOODEN LATH. THE LATH BROKE AND THE HAMMER HIT THE BACK OF HIS LEFT HAND. HE WAS WEARING INSULATED GLOVES, WHICH MAY HAVE TAKEN MOST OF THE IMPACT OF THE BLOW. AN ICE PACK WAS APPLIED AND HE WAS TAKEN TO THE ER, WHERE HIS HAND WAS XRAYED AND SPLINTED.

EE WAS CUTTING STRIPS OF GEO TEXTILE WITH A UTILITY KNIFE WHEN HE CUT THE INDEX FINGER OF HIS LEFT HAND, REQUIRING SUTURES. [EE IS PERFORMING ALL OF HIS JOB DUTIES].

EMPLOYEE WAS CHANGING OUT CUTTING EDGES ON A 16GMOTORGRADER. WHILE USING A HEEL BAR TO SLIDE THENEW CUTTING EDGES ONTO THE CARRYING DOLLY, THE EDGES SLIPPED OFF FROM THE HEEL BAR. EMP TRIED TO HOLD THEM AND GOT HIS LEFT MIDDLE FINGER TRAPPEDIN BETWEEN TWO EDGES, CAUSING A LACERATION THAT REQUIRED STITCHES.

EE WAS CHANGING OUT TWO BUCKET TEETH ON A FRONT END LOADER, IN THE FIELD. AFTER CUTTING OFF THE BENT PIN KEEPER WITH A TORCH, EE STARTED HITTING THE TOOTH WITH A HAMMER TO LOOSEN IT WHEN A MET AL CHIP CAME LOOSE, HITTING HIM IN THE RT LOWER LEG . THE WOUND REQUIRED TWO STITCHES.

EE WAS INSTALLING A TRACK PIN ON SHOVEL. HE WAS USING A 20# HAMMER. THE HAMMER SLIPPED OFF THE PIN AND PINCHED HIS LEFT LITTLE FINGER BETWEEN THE HAMMER HANDLE AND SIDE FRAME. EE SUFFRERED A C UT TO HIS LEFT LITTLE FINGER THAT REQUIRED STITCHES.

EMPLOYEES THUMB GOT CAUGHT BETWEEN WRENCH AND RODS WHILE RODS WERE BEING LOWERED.

INJURED WAS HOLDING A DRIVE BAR ON A BUSHING FOR#202 SHOVEL BUCKET. CO-WORKER MISJUDGED HIS SWING WITH A 20# SLEDGE HAMMER & STRUCK INJURED'S LEFT HAND. EE REPORTED THE INCIDENT, BUT THOUGHT I T WILL BE OKAY. ON 2/26/96 HE WAS SEEN BY THE COMPANY DR & RELEASED HIM TO RETURN TO WORK WITH LIMITATIONS & PRESCRIBED TO WEAR A WRIST BRACE.

WHILE DRIVING A STEEL FORM STAKE WITH A 10 LB SLEDGE HAMMER AND HOLDING THE HAMMER WITH BOTH HANDS, THE HEAD OF THE HAMMER MISSED THE END OF THE STAKE. THE FINGER WAS SMASHED BETWEEN THE HAMME R HANDLE AND THE TOP OF THE STAKE.

WORKING ON CUT 5, ATTEMPTING TO REMOVE OR LOOSEN A BOLT FROM A PUMP,K AS HE WAS PULLING ON THE WRENCH, HE FELT A POP IN HIS LOWER BACK. AS TIME WENT BY HIS BACK BEGAN TO HURT MORE AND HE WAS N OT ABLE TO STAND STRAIGHT UP. EE WAS PLACED ON LIGHT DUTY UNTIL REEVALUATED BY A DR.

EMPLOYEE WAS BREAKING 20' RODS ON THE GROUND. HE JUMPED ON PIPE WRENCH WITH HIS FOOT, SLIPPED OFF PIPE WRENCH AND TWISTED HIS ANKLE.

EE WAS TURNING A 120' LENGTH OF PIPE WITH A 24" PIPE WRENCH & THE WRENCH SLIPPED CAUSING BACK STRAIN. EE NOTIFIED SAFETY DEPARTMENT 12/4-95. WASSEEN BY DOCTOR ON 12/4/95 & PLACED ON RESTRICTED DUTY UNTIL RE-EVALUATED.

EMPLOYEE WAS HITTING A HOSE WITH A SLEDGE HAMMER ATTEMPTING TO UNPLUG A FEED LINE. THE HANDLE OF THE SLEDGE HAMMER WAS RESTING IN HIS LEFT PALM AND GOT PINCHED BETWEEN THE HANDLE AND A NEARBY HAND RAIL. EMPLOYEE'S INJURY REQUIRED SEVERAL SUTURES AND TWO DAYS OF RESTRICTED DUTY.

EMPLOYEE WAS STRIPPING CABLE TO PREPARE FOR TERMINATION AND KNIFE SLIPPED, LACERATION LEFT THUMBAPPROX. 1" IN LENGTH. EMPLOYEE PLACED ON ALTERNATE DUTY UNTIL 10/26/95.

EMP WAS MOVING NEW WHEEL COMPONENTS FOR NEW HAULTRUCK. EMP WAS ROLLING RINGS AND BREAKING DOWN WHEELS USING A SLEDGE HAMMER. INJURED LEFT LOWER BACK AND SIDE. EMP RETURNED TO WK - RESTR DUTY.