Buscar en el registro

THE INJURED WAS CHANGING A HOSE ON THE 563 BACKHOE. THE 3/4 INCH END WRENCH SLIPPED OFF THE OILY HEAD AND PINCHED HIS FINGER BETWEEN THE STEEL SLEAVE OF THE HOSE AND WRENCH. THE BLOOD UNDER TH E FINGERNAIL WAS REMOVED BY A DR.

INJURED WAS STANDING ON THE FRAMEWORK OF H-2 TAIL PULLEY TIGHTENING A WEAR PLATE BOLT ON 202 SCREEN CHUTE. AS HE DID THIS HE SLIPPED AND STRUCK HIS RIBS ON A WATER PIPE ELBOW. HE GRACTURED TWO RIBS. THIS WAS DETERMINED ON 1-24-00, AFTER GOING TO SEE THE DOCTOR.

EE WAS HOLDING BATTERY END OF A CABLWE WITH LEFT HAND AND WITH RIGHT HAND WAS CUTTING WITH A HACKSAW, THE HACKSAW SLIPPED AND CUT BETWEEN LEFT THUMB AND FOREFINGER.

CUTTING A PIECE OF BELTING WHEN HIS HAND SLID FROM THE HANDLE CUTTING HIS RIGHT INDEX FINGER-REQUIRED 3 SUTURES.

PINCHED RIGHT HAND INDEX FINGER BETWEEN HAMMER AND STEEL PLATE. REQUIRED 4 SUTURES.

LIFTING SCREEN PARTS WITH CHAINFALLS IN AN AWKWARD POSITION. BECAME DR. TREATMENT ON 3-12-96 WHEN HE SAW A CHIROPRACTOR.

INJURED PULLED CHAIN FALLS ON BEAM AND TROLLEY AND FELT PAIN IN NECK. EMP RECEIVED PHYSICAL THERAPY.

INJURED WAS SEPARATING GALVANIZED SHEETS WITH A BAR WHEN THEBAR SLIPPED CAUSING BACK STRAIN (HE SAW A CHIRPORACTOR)

THE INJURED WAS PULLING ON A SLUGGER WRENCH WITH A 1.5 TON RATCH FALLS TO TIGHTEN THE SPIDER NUTS AT THE SECONDARY CRUSHER. SUDDENLY THE WRENCH SLIPPED OFF THE NUT STRIKING THE INJURED ON THE LEFT KNEE WHICH CAUSED A BRUISE.

EMPLOYEE WAS CHANGING BIT ON A DRILL TO TAKE IT TO THE SHOP FOR RESHARPING THE BIT WAS STUCK AS HE TRIED TO PRY IT FR EE HE NOTICED BACK STRAIN

INJURED & COWORKER WERE REMOVING TOP IDLER FROM A CRAWLER IT WAS STUCK WHILE COWORKER TAPPED IT A PIECE OF STEEL FLEW FROM THE IDLER & BECAME LODGED INTO THE INJURED WRIST HE SAW A DR ON 06-29 -94 & 06-30-94 ON 07-02-94 A PIECE OF STEEL WAS REMOVED FROM HIS WRIST

INJURED WAS CHIPPING HOT SLAG FROMSCARFED AREA WHEN APIECE OF SLAG FLEW UP AND HIT HIM IN HIS NECK CAUSING BURNS.

INJURED WAS REMOVING FOUR BOLTS FROM A FENDER BRACKET HE DID NOT REALIZE THE FENDER BRACKET WAS UNDER PRESSURE HE USED A SMALL HAMMER TO TAP OUT THE BOLT WHEN IT SPRAING OUT & CUT THE NAIL & F INGER TIP ONE SUTURE WAS REQUIRED

EMPLOYEE WAS TRYING TO ALIGN HOIST, WHICH TWISTED AS VEHICLE WAS LOWERED DOWN AND WAS NOT ALLOWING POST COVER TO SEAT PROPERLY. THE POST COVER SLIPPED AND PINCHED HIS FINGER THE COVER AND HOIS T. BROKEN BONE IN FINGER TIP.

INJURED AND CO WORKDER WERE REMOVING A BELL CRANK PIN FROM 840 HAUL TRUCK THE PLATE HAD BEEN WELDED AND INJURED USED A HAMMER AND CHISEL TO TAKE THE PLATE OFF AS HE WAS POUNDING A PIECE OF MET AL CAME OFF THE PLATE STRIKING HIM ON THE RIGHT CHEEK, CUTTING IT REQUIRED SUTURES.

INJURED WAS USING A BAR TO PRY MATERIAL THAT WAS FROZEN TO THE DECKING OF E-4 CONVEYOR. DUE TO THE CRAMPED AREA IT WAS DIFFICULT TO WORK. HE TWISTED HIS BACK WHILE STRIKING MATERIAL. DECLARED DR ON 6-1-92 WHEN HE WENT TO SEE A CHIROPRACTOR.

WRENCH SLIPPED HIT ON L CHEEK, CHIPPING TOOTH

INJURED WAS CHANGING A BLADE ON A LINATEX CUTTER. WHILE USING AN END WRENCH TO REMOVE SCREW THE SCREW SUDDENLY LOOSENED AND HER RIGHT HAND STRUCK THE BLADE CAUSING A LACERATION REQUIRING 5 SUT URES.

INJURED WAS USING PRYBBAR TO TURN HYDRAULIC PULL DOWN CYLINDER SO THAT BOTTOM PIN COULD BE PUT IN. PRYBAR SLIPPED & INJ STRUCK HAND ON PULL DOWN CHAIN FINGER BEING CAUGHT IN LINK OF CHAIN. ACC IDENT OCCURRED ON ROTARY DRILL.

REPAIRING A THREE FOOT CRACK IN CARBODY TOP PLATE LAYING ON SIDE ON UNEVEN DECKING CAUSING MUSCLE SPASM

INJURED WAS CUTTING THE COATING OFF A THREE CONDUCTOR WIRE TO USE SINGLE STRANDS THE KNIFE SLIPPED OFF COVER INTO HIS HAND CAUSING CUT

INJURED WAS ALIGNING WEAR PLATES USING A PRY BAR THE BAR SLIPPED OUT OF PLACE & CAME LOOSE STRIKING HIS HEAD CAUSING LACERATION TO THE RT EAR (3) SUTURES

INJ WAS REPLACING 3/4 WATER PIPE ABOVE HEAD HEIGHT. AS HE WAS PULLING ON WRENCH PIPE COLLAPSED WRENCH CAME OFF & STRUCK HIM ON FOREHEAD.

INJURED WAS STANDING ON LEFT SIDE OF A HOIST GEAR CASE SHOWINT CO-WORKER HOW TO INSTALL CABLE CLAMPS. THE CABLE SLIPPED OFF DRUM AND LANDED ON A 1 7/8" BOX WRENCH CAUSING THE WRENCH TO FLY UP AND HIT HIM ABOVE LEFT EYE. NEEDED 3 SUTURES.

THE TRIPPER GATES WERE SET FOR STONE TO GO THRU. THE PILE WAS FILLING & TRIPPER GATES NEEDED TO BE OPENED MORE TO ALLOW THE "F" PORDUCT OVER THE END OF CONVEYOR. INJURED CLAIMED THAT WHILE TRY ING TO OPEN THE GATES BY SLEDGE HAMMER & LIFTING HANDLES HE INJURED HIS LEGS. INJURED DID NOT REPORT INCIDENT UNTIL 7-3-90 AFTER HE HAD GONE TO A CHIROPRACTOR FOR TREATMENT.

INJURED & COWORKERS WERE INSTALLING A 1/2IN T-1 PLATE ON THE OUTSIDE OF LOADER BUCKET THE ORIGINAL PLATE WAS BENT AC CLAMP & HEAT WAS USED TO STRAIGHTEN PLATE INJURED WAS USING A C RESCENT WR ENCH ON THE CLAMP WHEN THE C CLAMP SLIPPED OFF STRIKING HIM ON THE FACE & KNOCKING HIM DOWN HE RECEIVED A SMALL CUT & BRUISES UNDER LEFT EYE & A CUT ON CHIN (5 SUTURES ON CHIN)

INJ PUTTING NEW END ON WELDING CABLE.CUTTING OFF RUBBER FROM CABLE TO BARE ELEC CABLE,KNIFE SLIPPED AND CUT PALM OF HAND.

INJ & COWORKER MOVING ELEC MOTOR ACROSS GRADING ON VESSEL I.NAME TO PUT IT ON HOIST WHEN IT BECAME LODGED.INJ TRIED TO FREE IT BY PUSHING IT WITH A BAR,MOTOR SUDDENLY CAME FREE PINCHING FINGER CAUSING FRACTURE.

THE INJURED WAS ON THE VESSEL MC TAYLOR OPENING #2 HATCH. THE HATCHES ARE OPENED BY A WINCH AND CABLE. AS THE INJURE LET CABLE OUT FROM THE WINCH, A BACKLASH OCCURRED AND SUDDENLY PULLED HIM B ACK TOWARD THE WINCH. THIS MOTION STRAINED THE IJURED'S BACK. HE SAW A CHIROPRACTOR FOR TREATMENT.

THE INJURED WAS CHIPPING SLAG OFF A WELD ON THE VESSEL CYLMER WHEN A PIECE OF SLAG BOUNCED UP AND FELL BETWEEN HIS SAFETY GLASSES INTO THE RIGHT EYE.

EMPLOYEE WAS STANDING ON REAR PLATFORM OF L-07 TRUCK, REMOVING A NUT OFF A 1/4" CABLE CLAMP SO A NEW CABLE COULD BE INSTALLED. HE HAD EXTENDED HIS ARMS AWAY FROM HIS BODY WHICH PUT ADDED STRES S ON HIS BACK AS HE TURNED THE NUT WITH THE WRENCH CAUSING A BACK SPASM.

INJURED WAS REMOVING METAL SEAL OFF BARREL BUNG OPENING BY PUSHING WITH A PRY BAR OF PLAIRS. THE PLAIRS SLIPPED AND HIS FINGER WAS CUT BY THE PARTIALLY OPENED SEAL.

INJURED WAS SHOVELING DIRT INTO SKIP. WHEN SHE WENT TO GET ANOTHER SHOVEL FULL, THE SHOVEL HIT A BRICK IN THE DIRT AND SHE JAMMED HER WRIST.

THE INJURED WAS REMOVING THE BEARING HOUSING FOR 512 SCREEN ON THE 5TH FLOOR OF THE MILL BUILDING THE HOUSING BOLTS WERE TIGHT AND AS THE INJURED USED A WRENCH TO LOOSEN THEM THE BOLT SUDDENLY BROKE FREE CAUSING HIM TO STRIKE HIS ELBOW ON THE SCREEN FRAME ON 7/28 HIS ELBOW SWELLED UP AND HE WAS SENT TO THE DR TO HAVE THE FLUID DRAINED A SMALL BONE SPUR CAUSED THE FLUID ON HIS ELBOW

THE INJURED WAS WORKING IN THE STR. MUNSON S ENGINE ROOM REPLACEING BOLTS ON THE HIGH PRESSURE TURBINE. THE INJURED WAS HOLDING A SLUGGING WRENCH WHILE HIS PARTNER WAS HITTING THE WRENCH WITH A SMALL SLEDGE HAMMER. THE INJURED MOVED HIS HAND AS HIS PARTNER HIT THE WRENCH WITH THE HAMMER AND THE INJURED S INDEX FINGER WAS TRUCK WITH THE HAMMER.

INJ REMOVING WEAR PLATES FROM 409 FEED CHUTE IN MILL BLDG.INJ USING HAMMER TO HELP FREE PLATES.WHEN HE STRUCK PLATE WITH HAMMER DIRT & RUST FELL INTO LEFT EYE.SMALL STEEL SLIVER BECAME EMBEDDE D IN EYE AND WAS REMOVED BY DR.

INJ WA> GOING TO LOOSEN BOLTS ON HU B. WHEN HE PULED ON DRIVE RATCHET, SOCKET CAME LOOSE AND RATCHET. AHDNLE STRUCK HIM ON LIP AND REQ. 3 SUTURES.

INJURED WAS DIS5SSEMBLING A GRESE SWIVEL JOINT.HE DID NOT HAVE SNAP RING LPIARS SO WAS USING APOCKET KNIFE TO PRY THE SNAP RING FREE.WHILE APPLYING PRESSURE THE BLADE FOLDED CAUSING A LACERATI ION TO THE LITT5E FINGER,WHICH REQUIRED 4 SUTURES.