Buscar en el registro

Employee was pulling on a pry bar to remove the V-belts for the secondary shaker when releasing the pressure on the pry bar ee felt back tighten up.

Employee was changing teeth on an excavator bucket. Employee struck employee's hand with a hammer.

Employee was attempting to break up compacted material inside extruder hopper. Employee used a large auger part to strike the side of the hopper. Employee smashed employee's finger between the auger part and the hopper.

Employee was removing a drive chain from a gearbox with a pry bar. The pry bar slipped, smashing left index finger between the pry bar and gearbox. Employee's left index finger was fractured.

Employee was trying to remove a bearing from the bearing housing. EE was using a sledge hammer to knock the bearing loose. When EE struck the head of the sledge hammer against the bearing a small piece of metal flew off the bearing and punctured left leg. Employee received one stitch.

Employee was removing the motor connection cover. He had a box knife on top of the connection cover. When he broke loose the cover he cut his left hand with the box knife.

Employee was removing laces on C-10 belt. He was using a flexco punch to remove the laces, as he hit the punch a small metal shard struck him in the left chest.

At 8:45am EE was remodeling the birdhouse (load out shack). He shot his left index finger with a staple gun.

EE was shoveling underneath a conveyor belt. He struck an object embedded in the ground with the shovel. This caused a contusion to his right wrist.

Employee was installing new V-belts on K-3 shuttle drive using a pipe wrench to roll on belts when the pipe wrench slipped smashing his left index finger between the wrench and motor base. Employee suffered an open wound and hematoma.

Co-worker was using a hammer to drive the pin out of the excavator tracks employee was on the other side when the pin came out and struck his arm. This caused a large cut on employee's right forearm. He returned to work the following day.

Employee was installing a bearing on a conveyor head pulley shaft, he slid the bearing onto the shaft and was using a chisel and hammer to adjust the bearing. While hammering on chisel the employee felt something strike his left wrist, when he examined his wrist he could see a piece of metal embedded in his wrist.

Employee was using 56 inch pry bar to move chute on Primary Shaker, the pry bar slipped and employee fell back approximately 3 feet and struck rib cage on middle bar of the hand rail, fracturing ribs 7,8 and9 on his right side, doctor released him to restricted duty.

Employee was cutting a conveyor belt with a knife, the knife slipped and cut his right leg. Employee received four stitches and was return to work.

Employee was removing wiper blade on primary shaker, while loosening bolts he felt pain in his left shoulder and neck, he was examined by a physician and was released to work with restrictions and will follow up with doctor on 4-28-2011.

While installing tracks on a John Deere 750 Excavator, the 20' chain that was hooked from the bucket to the tracks to pull the track onto the track frame broke, striking the employee that was standing approximately five feet from the left track frame on the left forearm, hand and forehead. Employee was examined by physician and released to restricted duty.

REPAIRING PEA GRAVEL BELT WHEN UTILITY KNIFE CUT LEFT KNEE AREA. RETURNED TO WORK WITH NO CLIMBING, FOR ONE WEEK RESTRICTION.

EE WAS TRYING TO LOOSEN A NUT ON A MIRROR HEAD FOR A TRUCK DOOR. THE NUT WAS VERY TIGHT AND WHEN HE APPLIED PRESSURE THE NUT CAME LOOSE (SUDDENLY) CAUSING HIS FINGER TO BE CUT BY THE MIRROR BRACKET. RESULTING IN HAVING TO HAVE 6 STITCHES.

WORKING IN CLOSE QUARTERS WITH HEAVY ITEMS. BEARING & BEARING HOUSING WAS PUSHED ACROSS FLOOR WITH COMEALONG. RAISED & THEN TURNED AND LASHED INTO PLACE.

CLEANING AROUND CRUSHER WITH PRYBAR AND HAMMER. LEFT ARM FROM ELBOW TO MUD SHOULDER BLADE EXPERIENCING PAIN.

EE WAS REMOVING TEETH FROM TRACKHOE BUCKET. HE PLACED A 3/4" NUT IN PIN SLOT TO KNOCK PIN LOOSEWHEN HE STRUCK THE NUT IT SHOT BACK & HIT HIS LEFT HAND CUTTING & BRUISING IT. HE WENT TO DOCTOR & WAS TOLD WHILE IT WAS NOT BROKEN TO KEEP IT ELEVATED FOR A FEW DAYS. HE RETURNED TO WORK ON RESTRICTED DUTY & WILL SEE DOCTOR ON 1/5/01.

EE WAS ALIGNING TRACK PAD WITH COMEALONG AND FELT A SHARP PAIN IN HIS LOWER BACK. EE WENT TO THE DR. ON 9-20-00 AND THE DR. SAID HE HAD PULLED A MUSCLE IN HIS LOWER BACK. EE WAS GIVEN MEDICATI ON AND TOLD TO COME BACK ON 9-22-00.

EE WAS WORKING ON B-30 Y2143. REMOVING WHEEL HUB USING PIPE TO PRY HUB. PIPE SLIPPED CAUSING EE TO HIT LEFT SHOULDER ON FENDER. RESULTED IN FRACTURED CLAVICLE.

EE CHANGING TIRE ON PIT TRUCK WHEN BAR SLIPPED TRAPPING TIP OF FINGER, SERIOUSLY LACERATING.

TIHGHTENING BOLTS WITH A WRENCH. THE WRENCH BROKE, HITTING HIM IN THE HEAD. DID NOT CUT ANYWHERE.

EE WAS HOLDING CABLE OF DRAGLINE WHILE CO WORKER WAS USING WEDGE TO LOOSEN PIN. HE RECEIVED A PINCTURE WOUND WITH FOREIGN BODY.

EE WAS ATTEMPTING TO TIGHTEN THE NUTS ON SCREWS OF SHAKER. STRAINED GROIN, RIGHT SIDE, MUSCLE.

WHILE REPLACING A BUCKET TOOTH PIN, USING A HAMMER A PIECE OF METAL CHIP OFF AND HIT CHIN CUTTING IT. EE WAS TAKEN TO DOCTOR TO REMOVE PIECE OF METAL IN CHIN. RELEASE TO FULL DUTY THE NEXT DAY

REPLACING TEETH ON 180D DRAGLINE BUCKET, WHILE USING SLEDGE HAMMER AND PUNCH TO INSTALLL. ONE OF THE TEETH BROKE OFF AND A METAL FRAGMENT WENT INTO LEFT ARM.

REPAIRING FEEDER CHAIN ON PRIMARY JAW CRUSHER. REMOVING BOLTS WHEN DIRT GOT INTO RIGHT EYE.

EE WAS ATTEMPTING TO REPLACE BEARINGS ON WATER PUMP. THE SET SCREW WOULD NOT BREAK LOOSE, SO EE PUT AN ALLEN WRENCH IN HEAD OF SCREW AND TAPPED WRENCH WITH HAMMER. WHEN HE DID THE WRENCH FLEW UP AND HIT HIM IN THE RT EYE. PUNCTURED LENS OF RT EYE.

ADJUSTING SLIDER ON TRANSMISSION JACK, WHEN IT SLID CUT RIGHT INDEX FINGER.

REPLACING PINS ON DRAGLINE WALKING CHAIN WHEN SLEDGE HAMMER HEAD FLEW OFF HITTING HIM ON LEFT ARM.

EE & I WERE TURNING TEETH ON BUCKET & HAVING TO HIT TEETH WITH SLEDGE HAMMER I SWITCH PLACE WITHEE FROM HITTING TEETH & WHEN I WALKED OFF TO GEET EE HIT A PIECE OF STEEL FLEW OFF & WENT INTO M Y LEG

EE WAS TIGHTENING A BOLT WHEN HIS WRENCH SLIPPED AND HE STRAINED HIS BACK. HE WENT TO THE DR. ON 3-1-95, AND WAS PLACED ON LIGHT DUTY. LACK OF ATTENTION TO TASK AT HAND CONTRIBUTED TO THIS ACC IDENT.

EE HAD FINISHED USING A WIRE BRUSH TO CLEAN PORTOON TANK. EE WEARING FREE SHIELD AND SAFETY GLASSES BUT DUST PARTICLE MANAGED AND GET IN HIS RIGHT EYE.

EMPLOYE EWAS BREAKING UP CLAY CLODS ON TOP OF HOPPER WITH A PICK. PICK HIT A ROCK CAUSING PICK TO TWIST IN HAND & PULL TENDONS, OR LIGAMENTS, OR LEFT HAND.

REPAIRING MACHINERY IN AWKWARD POSITION & STRAINED BACK.

EMPLOYEE WAS CHANGING A TIRE. WRENCH SLIPPED. EMPLOYE EHIT RIGHT ELBOW ON TRAILER.

HE WAS CHANGING TEETH ON BUCKET, HE USED A HAMMER TO KNOCK TEH DIRT LOOSE FROM AROUND THE TOOTH. WHEN HE HIT THE TOOTH, A PIECE OF METAL FLEW OFF AND WENT INTO HIS LEG.

EMPLOYEE WAS USING A KNIFE TO CUT RUBBER STRIP TO REPAIR CONVEYOR BELT. KNIFE SLIPPED AND CUT LEFT THUMB.

EMPLOYEE WAS REMOVING A GEAR BOX IN A CONVEYOR STACKER. EMPLOYEE REACHE DFOR A HYD JACK AND RECIEVED AN INTENSE PAIN IN IS MID SECTION PART OF HIS BACK.

EE WAS INSTALLING A NEW TOOTH ON THE DRAGLINE BUCKET THE TOOTH WAS GOING ON HIGH WHEN EE HIT THE TOOTH WITH A SLEDGEHAMMER AFTER ABOUT 15 HITS WITH THE SLEDGEHAMMER A PIECE CHIPPED OF & WENT I NTO EE LEFT BICEP

SUBJECT NAMED BELOW WAS PRYING A ROCK WITH A PRY BAR AND SLIPPED STRAINING BACK.

DRIVER WAS CLEANING BED OF DUMP TRUCK WITH SHOVEL & WATER HOSE. LOWER BACK STARTED HURTING SOME TIME LATER.

EMPLOYEE WAS WORKING ON BRAKES ON TRUCK AND PULLED ON WRENCH TOO HARD AND PULLED MUSCLE IN BACK.

THEY WERE WORKING ON THE DRAGLINE BUCKET, HITTING THE TOOTH OF THE BUCKET WITH A SLEDGE HAMMER.

WAS CHIPPING ICE OFF LARGE BLOCK (10#) FOR USE IN PERSONAL WATER COOLER. KNIFE SLIPPED AND CUT RIGHT HAND.

SLIPPED AND HIT ARM WITH SLEDGE HAMMER WHILE ATTEMPTING TO TAKE PIN OUT OF DRAGLINE.

TWO EMPLOYEES, BOTH MECHANICS, WERE INSTALLING A CLUTCH W/ A HYDRAULIC JACK SET ON WOOD BLOCKS. AS THEY RAISED THE CLUTCH INTO PLACE, THE GROUND GAVE WAY UNDER THE BLOCKS & CLUTCH FELL OFF THE JACK STRIKING EMPLOYEE IN THE KNEE. HE RETURNED TO WORK THE FOLLOWING WORKING DAY & REPORTED THE ACCIDENT BUT DID NOT SEEK TREATMENT. IT GOT WORSE & HE WAS SENT TO A SPECIALIST WHO DIAGNOSIS