Buscar en el registro

Employee was using a sledge hammer to remove a pin from track hoe bucket. While striking the pin, a piece of the metal pin sheared off into employee's right shoulder.

Employee was using a sledge hammer to drive a pin out from a 330 CL track hoe. Had pain in right shoulder. Note: Employee previously had a similar claim on June 26, 2015, esulting with same complaint, (pain in right shoulder.)

Employee was replacing a hydraulic hose on a 966F loader. He was using a combination wrench to tighten the hose while standing in a awkward position, he felt pain in his right shoulder. Later he grasped the ladder on a 980G loader, that he was repairing and felt the pain again.

Hit a pin with a 20 lb. sledge hammer on a 980 g loader boom frame and upon contact a sharp pain and popping noise was experienced momentarily in left shoulder.

Cleaning return roller with shovel and return roller pulled shovel and right arm between conveyor belt and return roller bruising the right arm and wrist.

USING A WRENCH TO TAKE OFF HYDRAULIC CAP, WHEN IT BROKE LOOSE ARM HIT FENDER.

EMPLOYEE WAS CLEANING FEED HOPPER WITH SHOVEL WHEN A PIECE OF DEBRE GOT IN HIS RIGHT EYE.

EE WAS HOLDING A PIECE OF METAL KEY STOCK WHILE ANOTHER WAS HITTING ON IT WITH A SLEDGE HAMMER. A PIECE OF METAL BROKE OFF STRIKING EE ON HIS HAND.

EMPLOYEE WS WEDGING VOLUMN PUMP UP WITH A PINCH BAR AND PULLED MUSCLE IN BACK.

EE WAS SUING AN UTILITY KNIFE CUTTING TAPE FROM ELECTRICAL WIRES WHEN IT SLIPPED AND CUT HIS FINGERS.

CLEARING OFF SIDE BOX ON LOG WASHER WITH A SHOVEL - SHOVEL GOT HUNG AND HE FELL BACKWARDS.

CLEANING INSIDE HOPPER WITH A HOE--CUT INTO SMALL FINGER ON RIGHT HAND.

CLEANING OFF FEED HOPPER. SLEDGE HAMMER HANDLE GLANCED OFF METAL STRIKING RIB CAGE ON RIGHT SIDE.

EE WAS USING A SLEDGE HAMMER, HAMMERINGON BUCKET AND PULLED SHOULDER WITH CONTINUOUS HAMMERING.

EE WAS CLEANING OUT SPRAY BAR, USISNG A PIPE WRENCH. WRENCH SLIPPED & STUCK EE IN THE GROIN AREA.

WHILE HOOKING HOPPER, THE CHAIN SLIPPED IN HOISTHOOK. EMPLOYEE GRABBED HOPPER WITH RIGHT HAND, HOPPER FORCED EMPLOYEE'S RIGHT HAND BACKWARDS, CAUSING FRACTURE OF HIS RIGHT WRIST.

EE WAS DISASSEMBLING A GEAR BOX WITH A HAMMER AND PRY BAR WHEN A PIECE OF THE TOOTH FROM THE GEAR BOX CHIPPED OFF PENETRATING THE LEFT EYE LID AND OUTER EYE BALL.

WHILE MOVING SCREENS WITH A HOIST, THE SCREEN CAME LOOS STRIKING THE EMPLOYEE BRUISING HIS RIGHT HAND.

68935 REMOVING FRAME FROM UNDER CONVEYOR, THE EMPLOYEE PRIED A SHAFT PIN OUT OF THE LEG SUPPORT. WHEN THE LEG CAME LOOSE, IT STRUCK THE EMPLOYEE BRUISING HIS RIGHT SHOULDER.

54736YEE STRUCK A PIN WITH A HAMMER A SMALL PINE OF THE PIN BROKE OFF STRIKING THE EMPOLOYEE IN THE LEFT THIGH

WHILE DISASSEMBLING GEAR REDUCER BOX EMPLOYEE WAS USING A SCREWDRIVER TO PRY A SNAP RING OFF A SHAFT SCREWDRIVER SLIPPED CAUSING EMPLOYEES RT HAND TO STRIKE GEAR BOX CASE CUTTING RT INDEX FING ER

EMPLOYEE WAS USING INAPPROPRIATE TOOL TO TIGHTEN BOLTS ON DOZER ROLLER FRAME, RESULTING IN STRAINED STOMACH MUSCLE.

EMPL WAS STRETCHING FENCE USING CLAW HAMMER FENCE SLIPPED CUT THUMB.

WHILE INSTALLING HORIZONTAL TRAVEL SHACT IN DRAGLINE EE PLACED HIS RIGHT SHOULDER AGAINST PRY BAR TO APPLY ADDIDTION PRESSURE RESULTING IN BRUISNG HIS SHOULDER AT THE TIME IT WAS THOUGHT TO BE A MINER INJURY BUT AFTER A FEW DAYS PROBLEMS PERSISTED REQUIRING MEDICAL ATTENTION ON 4-25-91.

EMPLOYEE WAS CUTTING CONVEYOR BELTING, KNIFE SLIPPED AND HE CUT HIS THUMB.

EMPLOYEE WAS REMOVING BOLTS HOLDING CUTTING EDGE TO LOADER BUCKET AFTER REMOVING LAST BOLT THE CUTTING EDGE FELL STRIKING EMPLOYEE'S LEFT FOOT AND FRACTURING IT.

EMPLOYEE WAS PULLING ON WRENCH AND SPRAINED NECK MUSCLES.

EMPL STANDING AWKWARD POSITION TIGHTENING VALVE ON CRUSHER -STRAINED HIS BACK.

UNDER FEED HOPPER TIGHTENING BOLTS.

EMPLOYEE HAD HAND ON DOZER TRACK HELPING EMPLOYEE ROLL TRACKS FOR REPAIR BAR CAUGHT FINGER

EMPLOYEE WAS USING A 20 FT PIECE OF ANGLE IRON TO FREE GRAVEL STUCK IN HOPPER. HE STRUCK THUMB AGAINST SIDE OF HOPPER.

EMPLOYEE WAS PU5LING ON A WRENCH WHEN A PIN IN THE SECOND FINGER OF HIS RIGHT HAND CAME LOOSE.

I,NAME WAS CUTT3NG BELTING WITH A RAZOR BLADE KNIFE, TOWARD HIMSELF WHEN KNIFE SLIPPED AND CUT HIS LEFT THIGH.

EMPLOYEE WAS CL9ANING A PULLEY OFF, AND SHOVEL GOT HUNG HITTING HAND AGAINST CONVEYOR.

EMPLOYEE WAS CH5NGING TEETH ON LOADER BUCKET HE STRUCK AT A PIN WITH A HAMMER HE MISSED THE PIN AND HIT HIS THUMB ON HIS RIGHT HAND BRUISED THUMB.

EE WAS CUTTING 5 RUBBER BELT HE PULLED A KNIFE THRU THE BELT & INTO HIS LEG CAUSING AN INCISION THAT REQUIRED 4 STITCHES.