Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
The welder was holding a shaft the was being Line bored, when the shaft was hammered into the opening the worker's finger was shoved into the shaft and cut. Requiring Stitches.
Employee was cutting a piece of rope with a utility knife and cut the upper part of the thumb on their left hand.
2 employees working on the plant one of them was hitting a part with a hammer when it bounced off the part and hit the other employee in the mouth.
Employees working on screener in stone plant. After de-activating the power supply and locking out, went to remove the "v-belt" from the drive motor and had to use a wrench to brace the belt back from the motor. Tension from the pulley released when the employee completed a full rotation causing the wheel and belt to turn freely catching his finger between the tool and machinery.
Employee was cutting urethane for the plant with a utility knife. Utility knife slipped and he stabbed himself in the thigh.
Employee was removing bolts on a conveyor chute with a hammer and chisel. Employee struck his left thumb while hitting the chisel.
EE was adjusting the brakes on the rock truck. was pushing wrench with his foot and his knee popped.
EE WAS HELPING TO OPEN DOOR ON DEISTER ON SAND PLANT AND PULLED MUSCLE IN HER LOWER BACK AREA.
THE EMPLOYEE WAS IN THE PROCESS OF DRIVING A WEDGE (WITH A 5 LB SLEDGE HAMMER) WHILE ATTEMPTING TO REMOVE A CYLINDER WHEN THE WEDGE SUDDENLY BECAME DISLODGED AND RECOILED BACKWARDS STRIKING TH E EMPLOYEE IN THE FACE. EMPLOYEE RECIEVED A LACERATION ON THE BRIDGE OF NOSE, LACERATION ABOVE HIS LEFT EYE & COMPLAINED OF DIZZINESS. SUBSEQUENT VISITS TO LOCAL DR. REVEALS NO PERMANENT DAMA
THE EMPLOYEE WAS IN THE PROCESS OF LOOSENING A 9/16" NUT ON THE CATWALK OF THE CONCRETE SAND CONVEYOR WHEN THE ENERGY AND EFFOR TEXERTED TO BREAK THE NUT LOOSE CAUSED THE EMPLOYEE TO SUSTAINED A CERVICAL STRAIN IN THE NECK AND SHOULDER AREA OF HIS BODY.
THE EMPLOYEE WHO RECEIVED THE REPORTABLE INJURY SUSTAINE DA MINOR BACK INJURY WHILE ATTEMPTING TO RAISE AN OBJECT WITH A LONG HANDLED PRY BAR. DAMAGE TO THE BACK AREA AS A RESULT OF HIS ACCID ENT DOES NOT APPEAR TO BE SERIOUS AT THIS TIME. THE EMPLOYEE WILL CONTINUE TO RECEIVE THERAPY ONT EH BACK AS NEEDED UNTIL THE PROBLEM IS CORRECTE.D (THE INJURY WAS NOT REPORTED IMMEDIATELY AS
THE EMPLOYEE WHO RECEIVED THE REPORTABLE INJURY WAS IN THE PROCESS OF EXTRACTING A PIN HOLDING A STEERING CYLINDER HOUSING ON A CAT 980C LOADER WHEN HIS TAPPING ACTION ON THE SIDE OF THE HOUSI NG WITH A 4LB HAMMER CAUSED THE PIN TO SUDDENLY SHOOT OUT AND STRIKE HIM ON THE TOP OF THE HEAD. THE INJURY TO THE EMPLOYEE REQUIRED FIVE STITCHES TO CLOSE THE WOUND.
EMPL TIGHTENING DOWN MAIN BOLTS ON ENGINE BLOCK WITH A TORQUE WRENCH WHEN BODILY MOVEMENTS APPARENTLY PRODUCED STRAIN ON RIGHT KNEE RESULTING IN POSSIBLE CARTILAGE DAMAGE.
THE EMPLOYEE WHO RECEIVED THE REPORTABLE INJURY WAS ATTEMPTING TO REMOVE ELECTRICAL TAPE FROMT HE WIRING ON AN ELECTRIC MOTOR WHEN THE UTILITY KNIFE WHICH WAS BEING USED TO COMPLETE THE PROCED URE ACCIDENTLY SLIPPED FROM THE EMPLOYEE'S GRASP RESULTING IN A DEEP LACERATION OF THE THUMB ON THE LEFT HAND.
THE EMPLOYEE WHO RECEIVED THE REPORTABLE INJURY WAS ATTEMPTING TO MAKE REPAIRS TO A 3/4 HP DRILL PRESS WHEN A TENSION-LOADED SPRING LOCATED UNDER THE CAP COVER ASSEMBLY SUDDENLY UNCOILED, STRI KING THE EMPLOYEE'S HAND SEVERAL TIMES BEFORE HE COULD REACT TO THE SITUATION.
THE MECHANIC WAS ATTEMPTING TO DISLODGE A JACK HANDLE FROM ITS PROPER POSITIONING ON A SHOP HOIST WHEN THE JACK HANDLE SUDDENLY BROKE LOOSE,FLYING UP AND STRIKING HIM IN THE FOREHEAD.