Buscar en el registro

EE was installing a new grounding rod (3/4 copper) with a hammer. He missed the piece his hand took the impact slicing his left palm.

Employee working in possible 'bite' area if steel should break away from it's mount while forcing with come-along. Damage was to one of the employee's knee (right)

Employee was pulling on a crowbar and it slipped and hit him in the face.

Employee broke bolt loose and it snapped, hitting him in the eye under safety glasses.

Employee was pulling on a pipe wrench towards his face and wrench slipped off & struck him in the face.

EE REMOVING AND REPLACING V-BOLT SHEAVES ON DRIVE MOTOR. THEY APPLIED A GEAR PULLER TO SHAFT AND PULLEY AND STARTED TO APPLY PRESSURE, A LEGE OFTHE PULLER SLIPPED OFF THE PULLEY AND THE PULLER FLEW BACK AND HIT EMPLOYEE RIGHT SIDE OF HEAD JUST ABOVE THE EYEBROW.

EMPLOYEE WAS MOVING A CONVEYOR DRIVE PULLEY SHAFT WHICH HAD BEEN REMOVED FOR REPAIRS. HE WAS WORKING WITH TWO OTHER EMPLOYEES. HE USED A CHOCKER SLING ON THE SHAFT BETWEEN THE GEAR BOX AND BEA RING BUT USED A CHAIN ON THE OPPOSITE END TO FORM A TWO-PART SLING. THE CHAIN SLID OFF THE SHAFT& THE SHAFT STRUCK & KNOCKED EMPLOYEE TO GROUND.HE HAD SURGERY ON SAME KNEE 3 MO. AGO (SPORTS).

PUTTING DRIVER BELTS ON COUNTER WEIGHT. TURNED OVER AND PIPE WRENCH CAME OVER AND HIT FINGER.

SHOULD HAVE BEEN HOLDING PUNCH WITH CHANNEL LOCKS. HITTING A PUNCH, METAL CAME OFF AND HIT EMPLOYEE IN RIGHT HAND.

EE WAS USING A PRY BAR TO ATTEMPT TO DISLODGE A ROCK FROM THE TAIL PULLEY SECTION OF BAR DRY SCREEN OVERSIZE BELT. EE APPARENTLY HURT HIS BACK DUE TO HIS ACTIONS WITH THE PRY BAR. THE BELT HAD BEEN LOCED OUT PRIOR TO EE GETTING HURT.

EMPLOYEE WHERE CANGING APILLOW LOCK BEARING ON TEH RIGHT SIDE OF THE TAIL PULLEY, THEY WHERE USING A CHAIN COME A LONG TO PULL THE LOAD BACK & ANOTHER TO RAISE IT, WHILE IT WAS UNDER TENSION T HE INJURED WANTED TO RESET THE POSITION OF THE CHAIN TO ALLOW MORE CLEARANCE FOR THE BEARING. HE HIT THE CHAIN OVER WITH A HAMMER. HIS FOREARM WAS IN THE PINCH POINT EREATED FROM THE FRAME O

EE WAS CUTTING THE MOUNTING BELTS OFF OF A PILLOW BLOCK BEARING BEFORE CUTTING HE HAD PLACED A COME ALONG AROUND THE SHAFT TO HOLD IT BACK AND COMPENSATE FOR THE WEIGHT OF THE CONVEYOR BELTING THE PULL WAS IN A DIRECTION THAT ALLOWED THE BERING TO JUMP UP AND FORWARD WHEN THE BOLTS WERE CUT HIS WRIST WAS BRUISED WHEN THE LAST BOLT WAS CUT AND THE BEARINGS SLID FORWARD.

EMPLOYEE STATES HE WAS SPLICING 1 1/2 DIAMETER POLYPRO ROPE. WHEN DONE HE WAS CUTTING THE TAPE FROM END OF ROPE. HE ACCIDENTLY PLACED HIS LEFT INDEX FINGER UNDER KNIFE WHILE CUTTING AND CUT HI S LEFT INDEX FINGER ON THE DORSAL SIDE.

WHILE USING A PRY BAR TO DISLODGE A PULLEY THAT WAS BEING CHANGED, EMPLOYEE STATED HE HURT HIS BACK.

EMPLOYEE WAS CUTTING PIECE OF FIBER ROPE FROM THE CENTER OF WIRE ROPE DURING A SPLICING OPERATION. WHILE HE WAS CUTTING THE ROPE, THE WIRE SHIFTED AND HE CUT INTO HIS RIGHT INDEX FINGER.

EMPLOYEE WAS INSTALLING A SHAFT MOUNTED REDUCER AND TAPPING IT WITH A SLEDGE HAMMER.THE ELECTRICAL MOTOR WAS NOT BOTTOMED DOWN.THE VIBRATION MADE THE MOTOR SLIDE AND STRIKE THE EMPLOYEE.

WHILE CUTTING CHUTE RUBBER WITH RAZOR KNIFE,KNIFE PULLED THROUGH RUBBER AND CUT THIGH.

WHILE TOWING SCOW, THE PORT LINE SNAPPED AND HIT THE EMPLOYEE IN THE GROIN AREA.

WHILE HE WAS CLEANING ALONG PULLY ALONG B-4 CONVEYOR, HIS SHOVEL KICKED BACK AND HIT HIMSELF IN THE HEAD.