Buscar en el registro

EE was using CAT Backhoe to clean up area, removing scrap conveyor belt. He scooped up some belt with the bucket of the backhoe and got out to push the remaining into the bucket.

Daytime- Sunny- Off road conditions.

Working on the counter weight belt B4. In process of removing an old guard, employee knocked a piece of steel loose. After being informed that the piece was loose, an approximately 20 lb piece of angle iron came down and hit his hand.

Employee bent over to pick up a torch and his back locked up.

Putting 10' Length of 2" conduit in storage rack approx 35lbs to 45 lbs.

Walking by a trailer employee was started by a cat coming out of the weeds and tripped and fell on his leg breaking it.

EE was installing a new grounding rod (3/4 copper) with a hammer. He missed the piece his hand took the impact slicing his left palm.

Employee got out of his bulldozer to move a stacker. He attempted to cross a retaining wall and fell about 3 ft.

Employee working in possible 'bite' area if steel should break away from it's mount while forcing with come-along. Damage was to one of the employee's knee (right)

EE strained a muscle while moving sand from a belt. EE notified management on 01/11/2010 of injury and we started an investigation, and sent him to be examined on this date.

Pushing hand truck and slipped on gravel.

Employee slipped on ice.

Felt a groin pull when crossing from barge to ship.

Injured was attempting to clear blocked transfer chute when a large rock fell pinning his hand against a steel skirt board.

Employee was pulling on a crowbar and it slipped and hit him in the face.

Employee broke bolt loose and it snapped, hitting him in the eye under safety glasses.

Hernia--EE notified not to do any heavy lifting.

Employee was pulling on a pipe wrench towards his face and wrench slipped off & struck him in the face.

Slipped going through engine room door.

Employee picked up a 50 pound pump and threw his back out.

CONVEYOR BELT ROLLER FELL ON EE'S HAND.

Picking up plates hand got wedged between plate and concrete.

Pulled shoulder lifting a board.

EMPLOYEE WAS ADJUSTING CONVEYOR BELT TENSION WITH MANUAL COME-ALONGS. BELT CAUGHT ON A PIECE OF THE FRAME AND PARTED. EMPLOYEE WAS THROWN INTO A STEEL ANGLE.

EE BACKED A BOBCAT HE WAS DRIVING INTO A POLE. EE SAID HE WAS INJURED ON 8-14-03 BUT REPORTED INJURY ON 8-17-03.

EE WAS CARRYING A RAILROAD TIE WITH ANOTHER EE WHEN IT SLIPPED AND FELL ON HIS FOOT. EE WAS WEARING STEEL TOE SHOES BUT RAILROAD TIE HIT THE UPPER PART OF HIS FOOT.

EE STATED HIS ANKLE WAS HURTING AND IT MIGHT OF BEEN CAUSED BY MOUNTING OR DISMOUNTING HIS MACHINE.

EE WAS WORKING MOVING OXYGEN BOTTLES HE WAS INSTRUCTRED TO GET HELP UNLOADING THE BOTTLES. APPARENTLY HE LIFTED BOTTLES HIMSELF

EE REMOVING AND REPLACING V-BOLT SHEAVES ON DRIVE MOTOR. THEY APPLIED A GEAR PULLER TO SHAFT AND PULLEY AND STARTED TO APPLY PRESSURE, A LEGE OFTHE PULLER SLIPPED OFF THE PULLEY AND THE PULLER FLEW BACK AND HIT EMPLOYEE RIGHT SIDE OF HEAD JUST ABOVE THE EYEBROW.

PULLING WIRE EMPLOYEE ASSUMED INJURY TO WORK RELATED.

EE WAS HELPING TO SHOVEL SAND NEAR TAIL OF B-3 CONVEYOR. HE STEPPED OVER CONDUIT AND TWISTED KNEE.

EE STATES WAS COMPLETING CONVEYOR BELT SPLICE. WAS PULLING BELT TO STRAIGHTEN AND FELT PAIN IN BACK.

EMPLOYEE WAS LOADING EMPTY BOTTLES INTO BACKHOE BUCKET WHEN BOTTLE ROLLED OVER ONTO LEFT HAND. THE BOTTLE PINCHED HIS HAND AGAINST THE BACKHOE BUCKET.

EE STEPPED OVER A TROUGH IDLER THEN TURNED AND WITHOUT LOOKING TRIPPED OVER SAME IDLER.

EMPLOYEE WAS MOVING A CONVEYOR DRIVE PULLEY SHAFT WHICH HAD BEEN REMOVED FOR REPAIRS. HE WAS WORKING WITH TWO OTHER EMPLOYEES. HE USED A CHOCKER SLING ON THE SHAFT BETWEEN THE GEAR BOX AND BEA RING BUT USED A CHAIN ON THE OPPOSITE END TO FORM A TWO-PART SLING. THE CHAIN SLID OFF THE SHAFT& THE SHAFT STRUCK & KNOCKED EMPLOYEE TO GROUND.HE HAD SURGERY ON SAME KNEE 3 MO. AGO (SPORTS).

EMP WAS WALKING ALONGSIDE OF BARGE WHEN HE SLIPPED. AS HE STARTED TO FALL HE GRABBED THE RAILINGON HIS RIGHT SIDE. CAUGHT HIMSELF WITH HIS ARMPIT AND THE FORCE SPRAINED OR STRAINED RT SHOULDER

PUTTING DRIVER BELTS ON COUNTER WEIGHT. TURNED OVER AND PIPE WRENCH CAME OVER AND HIT FINGER.

SHOULD HAVE BEEN HOLDING PUNCH WITH CHANNEL LOCKS. HITTING A PUNCH, METAL CAME OFF AND HIT EMPLOYEE IN RIGHT HAND.

EE WAS CUTTING BOLS & REMOVING RUBBER FROM THE WATER (130X MAIN PLANT) AFTER TORCHING OUTTHE BOLTS HE REMOVED HIS CUTTING GOGGLES & PULLED ON THE RUBBER LINING MOLTEN RUST WHICH HAD STACK TO T HE RUBBER THEN POPPED OFF HITTING HIM IN HIS RT EYE

EE WAS USING A PRY BAR TO ATTEMPT TO DISLODGE A ROCK FROM THE TAIL PULLEY SECTION OF BAR DRY SCREEN OVERSIZE BELT. EE APPARENTLY HURT HIS BACK DUE TO HIS ACTIONS WITH THE PRY BAR. THE BELT HAD BEEN LOCED OUT PRIOR TO EE GETTING HURT.

EE STATED THAT HE WAS STEPPING UP ONTO THE BULLDOZER AND THAT HE MUST HAVE HAD MUD OR GREASE ON HIS WORK BOOTS AND THAT CAUSED HIM TO SLIP. HE PUT HIS RIGHT HAND OUT QUICKLY TO CATCH HIMSELF A ND JAMMED HIS RIGHT INDEX FINGER AGAINST THE DOZER PUSHARM. HIS FINGER WAS SWOLLEN AT THE 2ND JOINT.

EE & EE WERE TAKING AN OXYGEN BOTTLE OFF THE CRANE BARGE AT THE COAL DOCK THE BOTTLE SLID OFF A TIE UP LINE THEY HAD RESTED IT ON & FELL ON EE RT FOOT

EE WAS SHOVELING IN TUNNEL W/O VENTILATION FOR A WHILE AND COMPLAINED OF LUNG AND CHEST PROBLEMS.

EMPLOYEE WAS FREEING A FROZEN REEL. THE REEL WOULD NOT TURN IN THE COLD WEATHER & INJURED & HIS FOREMAN WERE PULLING ON REEL. WHEN IT FINALLY RELEASED THE INJURED'S LEFT ARM WAS STRAINED & A N ABRASION ON THE FOREARM FROM RUBBING AGAINST ADJACENT I-BEAM.

EMPLOYEE WAS USING A STICK TO LOOSEN SAND IN FEEDER (MANUAL) WHEN UNPROTECTED HAND STRUCK SIDE OF FEEDER.

EE WAS PULLING A WATER HOSE AND STEPPED BACKWARD INTO THE OPEN MANHOLE HE WAS CLEANING.

NO ACCIDENT, EE WAS PULLING MOORING LINE OUT OF WATER.

INJURED STATED THAT HE HURT HIS BACK KNEE BOARDING AT HOME PREVIOUS DAY HE THOUGHT THAT IT WOULD BE OKAY WHEN HE BACKED OVER A WINDROW HE FELT PAIN IN HIS BACK HE DROVE THE D8K DOWN FROM THE S TOCK PILE & WAVED FOR EE HE SAID HS BACK WAS VERY SORE SO WE CALLED THE SOUTH AMBOY FIRST AID THEY TOOK HIM TO THE HOLSPITAL TO BE CHECKED OUT

EE WAS CLOSING THE MANUAL BIN GATE IN THE B8A SURGE TUNNEL HE FIRST USED THE HANDLE PROVIDED BUT THEN THOUGHT HE COULD GET MORE LEVERAGE BY USING THE GATE IRON PART OF THE LEVER ARM. HE GRABBE D AND PULLED THAT BUT DID NOT OBSERVE THE PINCH POINT. HIS LEFT WRIST WAS BRUISED IN THE PINCH POINT.

EMPLOYEE WHERE CANGING APILLOW LOCK BEARING ON TEH RIGHT SIDE OF THE TAIL PULLEY, THEY WHERE USING A CHAIN COME A LONG TO PULL THE LOAD BACK & ANOTHER TO RAISE IT, WHILE IT WAS UNDER TENSION T HE INJURED WANTED TO RESET THE POSITION OF THE CHAIN TO ALLOW MORE CLEARANCE FOR THE BEARING. HE HIT THE CHAIN OVER WITH A HAMMER. HIS FOREARM WAS IN THE PINCH POINT EREATED FROM THE FRAME O