Buscar en el registro

The employee was using a shovel to try and get a rock out of the #1 conveyor belt scraper when EE hit hand on the conveyor. The next day the hand started swelling up so EE went to see a doctor. They told EE EE fractured the thumb and put EE on restricted duty for two weeks.

Employee was using a come along to change head pulley bearings when their right index finger got cut by getting caught between the come along and the conveyor transmission/gearbox.

Employee was working on the #1 conveyor removing a pulley with a pry bar and the pry bar hit them on the left side of the face causing a facial contusion.

Employee was using a razor knife to cut drive belts that were hanging from HP400 Crusher when employee cut self with the knife on left arm.

The miner was working on replacing a tramp release cylinder on a cone crusher, and went to use a hammer to remove a pin. The hammer slipped and hit EE's middle finger causing a cut.

While doing plumbing work, the employee caught left hand thumb between a pipe wrench and a jaw wrench. This caused the finger nail on EE's thumb to tear, EE went to the hospital where they gave EE stitches to repair it.

While adjusting a rubber curtain with a razor knife the employee cut EE's index finger

Employee was cutting wrapping material with a razor knife away from the head shaft on the 4 1/4 cone crusher when they sliced their thumb.

Employee was holding a slug wrench while another employee was striking it with a hammer. Employee swinging hammer missed the wrench and hit injured employee's hand.

Employee cut his knee while cutting a piece of rubber belt.

Employee was cutting a piece of conveyor belt with a plastic utility knife. The knife broke and the employee cut his finger.

Cut finger with razor knife while stripping a wire.

Tightening bolts on 4 1/4 crusher after adjusting it. Felt his back pull.

Employee was cleaning stone out of a screen with a pry bar. The bar jammed and the chisel end of the bar cut through his glove and into his hand.

Cutting rubber, knife hit employee in leg.

CRUSHED FINGER WHILE WORKING ON #3 SCREEN.

LOOSENING FROZEN DIRT FROM UNDER CONVEYOR USING SLEDGE HAMMER. RIGHT INDEX FINGER BECAME PINCHEDBETWEEN HAMMER HANDLE AND ANGLE IRON.

WAS REMOVING WEDGES FROM 5 1/2 CRUSHER USING SLEDGE HAMMER. HAMMER MISSED PINNING THUMB BETWEEN HAMMER AND WEDGE.

WORKING WITH ANOTHER EE TIGHTENING BOLTS ON JAW CRUSHER. SLEDGE HAMMER SLIPPED STIKING EE ON THUMB.

CUTTING SCREEN RUBBER.

WHILE TIGHTENING BOLT ON LOADER L-8 HAND SLIPPED AND CAUGHT CORNER OF STEEL AND TOOK OFF FINGERNAIL. RECEIVED 4 STITCHES.

PUTTING HOIST PISTON ON M50.HOIST PISTON STRUCK RIGHT HAND.HAND WAS CAUGHT BETWEEN PISTON AND FUEL TANK.8 STTICHES WERE REQUIRED TO CLOSE CUT.

TRIMMING THE EDGE OF CONVEYOR BELT (#1) TO MEASURE THICKNESS FOR SURVEY FOR COMPUTER INFORMATION. KNIFE SLIPPED CUTTING LEFT THUMB.

REMOVING BOLT FROM FRONT BUCKET OF LOADER CUT FINGER ON SMALL SHARP PLATE UNDER BOLT.

CUTTING SKIRT RUBBER FOR PLANT USING UTILITY KNIFE BLADE BROKE CUTTING FINGER ON LEFT HAND.

WORKING ON #2 CONVEYOR BELT WITH PRY BAR BAR SLIPPED HIT LEFT HAND ON CORNER OF ANGLE IRON PUNCTURE WOULD TO LEFT HAND.

TIGHTENING LOOSE BOLTS ON 4'CRUSHER,FELT PULL IM MIDDLE UPPER BACK.WORKED REST OF DAY,NEXT AM UNABLE TO STAND UP WITHOUT PAIN.

PUTTING ROOF ON DRAGLINE, ONE PERSON HELD ROOF UP WITH PRY BAR, PRY BAR SLIPPED AND FINGER WAS CAUGHT BETWEEN DRAGLINE ROOF AND GANTRY.

PUTTING SCREENS IN STEEL BINS, HAD TO BANG A SCREEN IN. WHEN HITTING SCREEN A PIECE BROKE OFF AND HIT ARM.

CUTTING RUBBER BELT WHILE KNEELING KNIFE SLIPPED AND STABBED KNEE