Buscar en el registro

WAS IN LOADER BUCKET SWINGING SLEDGE HAMMER DIRIVN GPIN I CASE ROCK PICK. WHILE SWINGING HAMMER HANDLE HIT BUCKET CAUSING ME TO MISS PIN & STRIAN BACK.

PRYING GRIZZLY SQUARE BACK INTO PLACE AND BAR SLIPPED AND EMPLOYEE FELL INTO GRIZZLY STRIKING RIGHT KNEE AND LEFT SHIN.

THE EMPLOYEE WAS RIDING THE SKIP, DRAIN HOLE WAS BLOCKED. HE USED A PIPE TO TRY TO CLEAR THE BLOKAGE, RAMMING THE PIPE TWICE. THE SECOND STROKE THE PIPE BROKE THROUGH AND BEFORE HE COULD PULL BACK, IT HUNG IN THE WALL PLATE SMASHING HIS RIGGHT HAND BETWEEN THE PIPE AND THE WALL PLATE.

INJURED WAS A TTEMPTING TO CUT A PIECE OF CLOTH TAPE WITH A UTILITY KNIFE IT SLIPPED & CUT HIS LEFT THIGH 4 STITCHES WERE NEEDED TO CLOSE THE CUT

THE EMPLOYEE WAS IN THE LOADING POCKET PUTTING BOLTS ON THE HOPPER, WHILE TRYING TO WIDEN THE HOLE WITH A PIECE OF STEEL, HE HIT THE STEEL WITH A HAMMAR AND A PIECE OF STEEL WENT UNDER HIS GAL SSES STRIKING HIS EYE.

EMPLOYEE WAS PULLING OUT A CYCLINDER IT BECAME JAMMED HE CONTINUED TO WINCH THE CYCLINDER WHEN IT BROKE LOOSE AND SWUNG AROUND AND HIT HIS FOOT.

EMPL SCALING WALLS OF SHAFT BEFORE BOLTING AND STRUCK INDEX FINGER LEFT HAND AGAINST RUSTY BOLT THAT WAS CUT OFF.4 OR 5 STITCHES PUT IN AND RET.TO WORK.

EMPLOYEE WAS TAKING BOLTS OUT OF GUIDES TO GET TWIST OUT OF THEM.A WRENCH SLIPPED AND CAME BACK AND HIT HIM IN THE RIGHT EAR.

WORKER WAS LOWERING SEALING BAR BY ROPE FROM 2384 PLATFORM TO SHAFT MINERS UNDERNEATH. BAR GOT HUNG UP 2 SETS ABOVE MINERS. ROPE BUILT UP SLACK & BAR LET LOOSE FALLING & STRIKING EMPL FON TOP OF SHOULDER.

MACHINCS NEEDED SOMEONE TO HELP IN THE SHOP. THE WORKER WAS HOLDING A CHISEL TO POUND A BOLT INTO BOOM JOMBO WITH 16 POUNDER. HAMMER GLANCED OFF CHISEL STRICKING THE WORKERS RING FINGER ON T HE LEFT HAND.

MINER STANDING IN 1284 LEVEL SHAFT ACCESS CUTTING AWAY LOOSE WIRE WHEN PIECE OF LOOSE WIRE FELL STRIKING HIM IN THE BACK.

INJ USING CRESCENT WRENCH INSTEAD OF SOCKET TO LOOSEN BOLTS FOR RETAINER ON MICARTA BUSHING OF GRINDING MILL.IT SLIPPED OFF BOLT HEAD PINCHING FINGER,CUT ON MIDDLE FINGER LEFT HAND AND CRACKED BONE IN FINGER.

EMPLOYEE INJURE8 HIS BACK AT HIME AND REQUIRED HOSPITALIZATION WITH SEVERE BACK PAIN.

FINGER CAUGHT B9TWEEN PIPEWRENCH AND MAST.

TIGHTENING BOLT8 ON A DOZER ILLER.WRENCH SLIPPED AND HAND HIT METAL.TOP PORTION OF HAND REQUIRED STITCHES.

EMPLOYEE WAS PU5LING A WRENCH HANDLE WHILE WORKING ON THE DOZER. HE FELT A TWINGE OF PAIN GO DOWN HIS BACK INTO HIS RIGHT LEG. AFTER A VISIT TO THE DOCTOR, IT WAS FELT HE PULLED A MUSCLE IN HIS BACK. 3

MECHANIC WAS RE4OVING A BEARING RACE FROM THE SHAFT. HE ATTEMPTED TO POUND OFF THE BEARING RACE AND A PIECE OF METAL BROKE OFF AND LODGED IN HIS NECK

EMPLOYEE WAS IN8TALLING EPOXY BOLT ON THE 1020 LEVEL. HE AND ANOTHER MINER WERE PUSHING THE EPOXY BOLT INTO A HOLE WHEN THE HAMMER SLIPPED OFF THE BOLT. THE BOLT CAME SLIDING BACK OUT OF THE H OLE STRIKING I 3AME IN THE FACE.

I.NAME WAS DIAM2ND DRILLING ON THE 1152 LEVEL AS HE WAS REMOVING THE DRILL BIT THE PIPE WRENCH HE WAS USING SLIPPED ON THE DRILL BIT AND TWISTED HIS WRIST

THE INJURED WAS ATTEMPTING TO OPEN A JAMMED TAILGATE ON HIS PRODUCTION TRUCK USING A PRYBAR. AS H E PRIED HE FELT A PAIN IN HIS LOWER BACK. I.NAME IS CERTIFIED THROUGH VOCATIONAL REHAB FOR A BAD BACK. THIS ACCIDENT MAY BE DETERMINED AS A REOCCURRANCE OF A PRE--EXISTING CONDITION.

I NAME WAS ATTEMPTING TO HOIST A 900 LB COMPRESSOR CYLINDER USING AN EYE BOLT THAT HAD BEEN INSERTED INTO THE BOLT HOLE THE EYE BOLT BROKE LOOSE DROPPING THE CYLINDER ONTO THE CONCRETE COMPRES BASE THEN ONTO THE FLOOR WHERE IS SUBSEQUENTLY ROLLED ONTO HIS FOOT BREAKING THE FOURTH METATARSAL OF RT FOOT

MINER WAS LOWERING HEADING ON 4900 STATION TO INSTALL WOODEN FLOOR USING AX TO TRIM TIMBER HE HIT HIS RIGHT FOREARM WITH HIS AX ON THE BACK SWING 2 CUT ON RIGHT FOREARM 6 STICHES.