Buscar en el registro

EE wrote was pitching mud out of k-4 chute and rock rolled down and hit backside of hand and wrist. Doctor put EE on modified duty on 5/8/2019. EE is not to use right arm until follow up appointment.

Cutting new skirt rubber knife came off rubber cut right leg employee received three stitches was put on restricted duty for one week

Was holding up skirt board rubber while pulling a belt on when the pry bar came in contact with the tail pulley pinching finger between the pry bar and I beam. Employee was put on light duty or restricted duty.

Lining up truss on F-5-B with come a long when chain broke hitting EE right wrist. Physician performed procedures Laceration/wound repair at Dearborn county Hospital phone 8125378240

EE was working on the Telsmith #44 tightening bolts. Wrench slipped off the bolt causing him to fall into the belt guard and motor. He received a scraped shin and buttocks. He did not go to the doctor until 5/20/08.

Employee was cutting a toggle bearing out and when he went to pry it off, it fell out and hit his left foot, behind his steel toe.

Employee was installing liners in M-2 Syntrons. The pry bar slipped and hit his upper lip and lacerated it.

EE was trying to unplug the crusher using a pry bar and hammer. While he was driving the bar into the material, he hit his index finger on his right hand. His finger was laid open.

Employee was cutting the belt off on M-17 conveyor and slipped. He hit his knee with the belt and slipped and cut his knee. Due to weather conditions, this was a factor in the injury.

Inj Employee and another employee, were replacing return rollers on m-23 converyor and while trying to break the bolt loose, the bolt broke, causing inj EE to ram his elbow against the trough roller assembly.

He was working in a small electrical box and was stripping a wire and cut his left forearm.

Ee was attempting to pry loose bridged conglomerate from crusher opening. the bridged material came loose and caused the pry bar to hit him in the head.

INSTALLING V-BELT HAD A COME ALONG ON REDUCER TO PULL TURNBUCKLE BACK. COME A LONG CAME LOOSE, REDUCER TURNED AND HIT EE S TAILBONE.

EE WAS USING A COME-ALONG TO REMOVE A MOTOR FROM A SLURRY PUMP. WHILE PULLING ON THE COME-ALONG THE EYE RING IN THE MOTOR BROKE OFF CAUSING EE'S ARM TO HIT A HAND RAIL.

EE WAS PRYING THE COUNTERWEIGHT OFF OF THE FLOAT SIDE BEARING, THE PRY BAR SLIPPED & HIS HAND HIT THE CORNER OF THE COUNTERWEIGHT. IT TORE HIS SKIN.

EE WAS CUTTING THE BELT & LOST HIS FOOTING, CAUSING HIM TO CUT HIS FINGER.

EE WAS USING A PORTAPOWER AND WHEN THE PRESSURE WENT UP HYDRAULIC FLUID LEAKED AND HIT EE IN THEEYES. (THE PRESSURE IN THE HYDRAULIC HOSES CAUSED THE FLUID TO SPRAY FROM OUT AROUND COUPLINGS).

EE WAS SWINGING A SLEDGE HAMMER, HITTING A BOARD TO INSTALL THE HOUSING. THE HAMMER KICKED BACK AND EE'S HAND HIT A PIN ON THE SHAKER.

EE WAS ATTEMPTING TO DISLODGE A ROCK FROM THE GRIZZLY, WITH A SLEDGE HAMMER, AND THE ROCK HIT HIM IN THE CHIN.

THE MEN WERE REMOVING A TAIL PULLEY, USING A PULLING BAR TO MOVE THE BELT BACK AND THE LUG BROKE. THE CHAIN AND LUG OFF OF THE BAR HIT INJURED IN THE FACE.

EE WAS HOOKING UP COMEALONG AND BENT HIS LITTLE FINGER BACK.

EE WAS USING A COME-A-LONG TO GET THE NORDBERG CRUSHER LOOSE. HE APPLIED PRESSURE TO THE COME-A-LONG AND IT STRIPPED. HE LOST HIS BALANCE AND FELL TO THE CRUSHER DECK FLOOR, HITTING HIS HEAD A ND ARM ON THE CRUSHER DECK HAND RAILING.

EE WAS USING A BREAKER BAR TO LOOSEN BOLTS ON CUTTING EDGES & HURT HIS LOWER BAKC

EMPLOYEE WAS CUTTING THE BELT TO MAKE A SPLICE ON M-6. HE CUT HIS FINGER.

HE WAS INSTALLING A NEW TORCH ON HOSES. THE WRENCH SLIPPED OFF THE HOSE NUT & STRUCK HIM UNDER HIS RIGHT EYE

HE WAS UNLOADING CHAINS & COMEALONG FROM 1 TRUCKTO ANOTHER. HE PULLED ON A CHAIN & COMEALONG WASHOOKED AND IT FELL ON HIS LEFT FOOT BEHIND THE STEEL TOE OF HIS BOOT

EMPLOYEE SAID HE WAS PUSHING MUD OFF THE CONVEYOR BELT WITH A RAKE WHEN HE HURT HIS BACK.

HE WAS INSTALLING BACK PLATE ON CHANGEOVER CHUTE. WHILE USING A COME-A-LONG TO PULL PLATE INTO PLACE THE PLATE GOT HUNG UP. ATTEMPTING TO FREE PLATE, HE PUT FINGERS BETWEEN PLATE AND PLATE MOU NTS. PRESSURE CAUSED PLATE OT POP INTO PLACE MASHING FINGER.

EMPLOYEE WAS KNOCKING BUCKET TOOTH OFF WITH SLEDGE WHEN A PIECE OF METAL HIT HIS KNEE.

EMP WS USING A 5' PIPE AS A PRYBAR. HE LEANED IT AGAINST THE REAR TIRE OR THE TRUCK HE WAS WORKING ON. HE JACKED UP THE REAR OF THE TRUCK AND PIPE FELL ON HIS LEG.

HE WAS KNOCKING WEDGES LOOSE TO ADJUST THE CRUSHER DOWN 1 RIB. AS HE WAS SWINGING THE HAMMER, THE HANDLE GLANCED AND THE HAMMER HIT THE TOP OF HIS RIGHT FOOT. HE HAD STEEL TOE BOOTS ON, BUT TH E HAMMER HIT BEHIND THE STEEL TOE. CRUSHER HAD ALOT OF MATERIAL BUILT UP AROUND IT AND LIMITED THE SPACE TO STAND.

HE WAS CHANGING THE TAIL PULLEY ON F-1B. WHILE PUTTING THE PULLEY BACK IN THE CONVEYOR, THE COME-A-LONG SLIPPED AND THE PULLEY HIT THE SIDE OF HIS LEG.

EE WAS USING A TIRE IRON TO PRY A TORQUE ARM OFF OF A SEMI TRACTOR WHEN THE TIRE IRON SLIPPED OFF AND HIT EE IN THE MOUTH CHIPPING UPPER CENTER RIGHT TOOTH AND RIGHT EYE TOOTH.

HE WAS FREEING TRA'S ON THE TAIL OF M-55. HE WASUSING A 4 LB. HAMMER AND WHEN HE WENT TO HIT AT A ROLLER, HE MISSED AND HIS HAND WENT BETWEEN THE ROLLER AND THE BELT.

HE WAS REMOVING A SPRAY NOZZLE FROM A SPRAY BAR & THE WRENCH SLIPPED & HE HIT HIS RIGHT HAND ON ANOTHER SPRAY BAR NOZZLE.

HE WAS BREAKING PIPE UNION APART WITH A PIPE WRENCH.

EMPLOYEE WAS IN SHOP WORKING BETWEEN TANDEM WHEELS OF STOCK TRUCK BENT OVER IN AN AWKWARD POSITION AND INJURED HIS BACK TIGHTENING BOLTS ON FRAME.

HE WAS HAMMERING IN SLIDES ON SAND GATES IN M-23 TUNNEL.

HE WAS STRIPPING COATING OFF OF A FLEX CONDUIT WITH A UTILITY KNIFE & THE KNIFE SLIPPED & CUT HIS RT INDEX FINGER

HE WAS USING A 1 1/2 TON COME ALONG TO PULL A CONVEYOR BELT TOGETHER SO THAT IT COULD BE SPLICED . HE WAS APPROXIMATELY 15 FT FROM THE GROUND WHEN THE COME ALONG EITHER SLIPPED OR FAILED TO WORK PROPERLY CAUSING HIM TO LOOSE HIS BALANCE AND FELL.

HE WAS HELPING TO CHANGE THE DRIVE SIDE ECCENTRIC BEARING. HE WAS SWINGING THE HAMME (SLEDGE) HORIZONTALLY TO DRIVE THE HOUSING BACK IN PLACE. HE FELT A POP IN HIS MIDDLE BACK.

EMPLOYEE WAS USING A 2" WRENCH TO HIT SKIRTING ON #4 TAIL PULLEY TO LINE UP BELT. WRENCH CAME BACK AND HIT EMPLOYEE, CUTTING HIS RIGHT INDEX FINGER.

EMPLOYEE WAS CHIPPING SLAG WHEN A PIECE HIT HIS EYE.

EMPLOYEE WAS INSTALLING HIM IN JAW CRUSHER WHEN HE HIT HIS FINGR WITH HAMMER 9 STICHES IN RIGHT INDEX FINGER.

REMOVING LARGE SPROCKET ON HEAD ON #1 CONVEYOR. CHAIN GUARD WAS OFF, EXPOSING ANGLE IRON THAT HOLDS GUARD IN PLACE. STRUCK HEAD ON SAME AS HE GOT UP FROM KNEELING POSITION.

HE WAS RELINING THE CHUTE TO M-5. HE WAS WORKING THE COME ALONG TO PULL THE LINER IN PLACE. HE PUT PRESSURE ON THE COME ALONG AND THE HANDLE SLIPPED AND HIT THE TOP OF HIS HAND.

HE WAS SPLICING ON M-67 CONVEYOR. AS HE WAS SQUARING THE BELT, HIS KNIFE CUT HIS THUMB.

HE WAS HELPING CHANGE BUCKET TEETH ON PIT LOADER UNIT #49 AS HE WAS HITTING THE BUCKET TOOTH WITH A SLEDGE HAMMER A PIECE OF THE TOOTH CHIPPED OFF & STRUCK HIM IN THE LEFT LEG

INJURED WAS DRIVING IN WEDGES ON K-5 SHAKER WHEN A PIECE OF METAL HIT HIM IN THE EYE.

HE WAS WORKING GATES IN M-23 TUNNEL BECAUSE OF FROZEN LUMPS.WHILE STRIKING THE BIN GATE WITH AHMMER,HE INADVERTETLY HIT HIS ARM.