Buscar en el registro

USING A WRENCH TO TIGHTEN BOLTS. THE WRENCH SLIPPED, CUTTING HIS RIGHT RING FINGER.

EE WAS USING A HAMMER, MISSED AND HIT HIS RIGHT INDEX FINGER.

EE WAS STRIKING A SHAFT WITH A SLEDGEHAMMER WHEN A PIECE OF METAL CHIPPED OFF AND EMBEDDED IN HIS ARM.

EE WAS BEATING ON THE KILN DISCHARGE SCREW HOPPER WITH A 10FT PIECE OF HEAVY STEEL. HE HAD BEEN INSTRUCTED TO WAIT UNTIL THE PROPER TOOL HAD BEEN BROUGHT (SLEDGE HAMMER). HE REACHED OVER HIS H EAD AND PULLED A MUSCHLE.

CREW WAS WORKING TO REMOVE LARGE SPRING FROM SOUTH PIT CRUSHER. HYDRAULIC JACK WITH SPACERS WAS IN USE TO ALLOW REMOVAL OF SPRINGS. SPACER WAS NOT TIED OFF AND FLEW OUT HITTING EE IN THE HEAD, SLIGHTLY DEFLECTED BY HIS HARD HAT AND SAFETY GLASSES.

EE WAS USING 20 LB SLEDGE HAMMER TO DRIVE OUT BRAKER BELT IN CRUSHER. EE STATED THAT HE PULLED HIS BACK.

WAS USING A 2 INCH PIECE OF PIPE 3 FT LONG TRYING TO PRY THE TUB AWAY FROM THE CHAIN CHAIN WAS RUBBING IN TUB WHILE ATTEMPTING TO DO THIS HIS LEFT HAND SLIPPED OFF THE PIPE CAUSING HIM TO HIT THE TOP OF HIS FINGERS ON HIS LEFT HAND AGAINST THE ROUGH PART OF THE GUARD.

WHILE CUTTING RUBBER FOR WIPER ON BELT KNIFE SLIPPED OUT RIGHT LEG ABOVE KNEE.

EMPLOYEE WAS HELPING MECHANIC HOLDING THE ROD UP ON OPPOSITE SIDE OF EQUIPMENT WHILE BEING RAISED BY A JACK THE ROD JERKED FORWARD CAUSING EMPLOYEE TO LOOSEUP & THREW HIMSELF BALANCE CAUGHT HI MSELF FROM FALLING TO FLOOR & HAND HIT STEERING KNUCKLE THAT WAS ON THE FLOOR

EMPLOYEE WAS HOLDING A PIECE OF KEY STOCK 1 1/2" X24" ON A BUSHING WHILE BEING HIT WITH HAMMER BY ANOTHER EMPLOYEE. HE SLIPPED WITH KEY STOCK WHILE BEING HIT AND CUT FINGER ON STEEL OF 3 SP.R EDUCER.

ASSEMBLING DRIVE CHAIN ON DRAGLINE. DRIVING PIN INTO PLACE WITH A HAMMER. PIECE OF METAL SPLINTERED OFF PIN AND WENT INTO LEFT FOREARM.

EE WAS STRIPPIN1 WIRE WITH A KNIFE WHEN IT SLIPPED ON INSULATION & CUT ARM. .

EMPLOYEE WAS RE4OVING BOLT WHEN WRENCH SLIPPED GREASE ON HANDLE. HIT LEFT BAND ON JAGGED PIECE OF FRAME WHEN HE SLIPPED.

USING RATCHET W9ENCH REASSEMBLING PUMP CASING-FELT PAIN IN RIGHT SHOULDER.

EMPL BUILDING S7AFFOLD AND HIT FINGER WITH HAMNMER.

EMPLOYEE WAS CU7TING A PIECE OF CONVEYOR BELT FOR THE TALLGATE ON BOHINER 2 KNIFE CUT THRU BELT SUDDENLY AND WENT INTO RIGHT THIGH.

THE DRAGLINE OP9RATOR HAD A PISTOL ON THE DRAGLINE IT ACCIDENTLY WENT OFF AND HIT THE OILER IN THE LEG

EMPLOYEE WAS CH5NGING SCREENS ON TOP OF THE PLANT, AND THE BAR SLIPPED AND FELL ON HIS THUMB.

EMPLOYEE WAS GR5BBING SHEETS THAT WERE BEING PULLED UP AND HELPER PULLED ROPE AFTER I.NAME GRABBED SHEET AND THE SHEET STRUCK HIS ARM AND CUT IT

EMPLOYEE, A SHOVEL OPERATOR WAS ATTEMPTING TO INSTALL A SPRING ON THE CABLE TRIP CONTROL HIS HAND SLIPPED OFF THE SCREWDRIVER THAT HE WAS USING AND HIS HAND WENT INTO THE CABLE SPOOL OR GEAR.

EMPLOYEE WAS ON TOP OF DRAGLINE ADJUSTING DRAG BRAKES THE WRENCH HE WAS USING SLIPPED AND EMPLOYEE FELL FROM THGE TOP OF DRAGLINE AND LANDED ON THE DRAGLINE TRACK ON HIS BACK

EMPLOYEE CUTTING CONVEYOR WITH JACKKNIFE IT FOLDED AND HE CUT MIDDLE FINGER AND TOP LEFT HAND REQUIRED SEVERAL SUTURES

USING PIPE WRENCH WORKING ON PUMP SHAFT,WRENCH SLIPPED HIT LITTLE FINGER ON STELEL PIPE CASING.