Buscar en el registro

EE & EE WERE REMOVING A 4IN PIPE OT OF A 12IN CONCRETE WALL EE WAS HOLDING A PUNCH EE WAS HITTING IT W/A 8LB SLEDGE HAMMER TO DRIVE THE PIPE OUT OF THE WALL EE MISSED PUNCH & HIT EE RT THUMB

TRIMMING SKIRT BOARD RUBBER WITH STANLEY CARPET KNIFE. EE WAS KNEELING DOWN CUTTING RUBBER ON FLOOR. THE KNIFE SLIPPED, CUTTING EE S LEFT LEG.

USING UTILITY KNIFE TO STRIP WIRE AND SLICED FINGER WITH BLADE.

EE WAS TEARING DOWN CRUSHER, USING A 3# SLEDGE HAMMER, HAND SLIPPED & IMPACT WAS MADE TO RIGHT HAND.

EMPLOYEE WAS GRINDING UNDERNEATH THE CRUSHER, USING A HAND HELD BODY GRINDER. HE HIT A PIECE OF STEEL, AND IT "KICKED" THE GRINDER BACK AT HIM, GOING INTO HIS LEFT LEG JUST ABOVE THE KNEE CAP. THE LEG WAS LACERATED, WHICH REQUIRED SUTURES.

EE WAS CLEANING DIRT FROM A FRONT END LOADER TO GET TO A BOLT. HE WAS USING A 2 LB HAMMER AND PUNCH TO FREE THE HARDENEND MUD AROUND THE BOLT. HE HIT HIS LEFT HAND INSTEAD OF THE PUNCH. THIS C AUSED THE INJURY.

EMPLOYEE WAS CHANGING SCREENS. WHILE REMOVING BOLTS, HE STRAINED BACK MUSCLE.

TAKING BELLY PAN OFF OF 988 LOADER, BOLT BROKE AND PAN FELL ON LEG.

BRUISE RIBS. TAKING BOLT LOOSE LAYING OVER WRENCH USING HIS WEIGHT TO LOOSEN BOLT.

EE WAS USING A 5 FT PRY BAR ON A ROLL AWAY STONE CHUTE TO POSITION IT PROPERLY. EE STATED HE WAS PRYING AND BENT OVER TO INSTALL A LOCKING PIN WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK.

LOOSENING BOLTS ON TRUCK TO CHANGE REAR AXLES PULLED ON WRENCH BACK WENT OUT OF PLACE

THE EMPLOYEE WAS SHOVELING SPILAGE FROM A CONVEYOR.THE PLANT OPERATOR READY TO START SOUNDED THE BUZZER.THE EMPLOYEE WAS STARTLED BY THE SOUND AND HE JUMPED BACK INTO AN IRON SUPPORT BEAM,APPR OXIMATELY 3" TO 4" FROM WHERE HE WAS STANDING.

EE WAS HOLDING A PUNCH WITH HIS LEFT HAND. OTHER WAS HITTING THE PUNCH WITH A SLEDGE HAMMER. HE MISSED, THE PUNCH HIT EE MIDDLE FINGER ON HIS LEFT HAND.

THE EMPLOYEE WAS USING A PULLER TO REMOVE SLIDE LAGGING FROM THE HEAD DRIVE ON A CONVEYOR.THE PULLER BROPKE AND THE WORKER HIT HIS RIGHT ELBOW ON THE SAFETY RAILING OF THE CONVEYOR CAT-WALK.

WAS OPENING A 50LB TIN CAN OF WELDING ELECTRODES WITH A SMALL HAMMER & CHISEL JAGGED EDGE WAS VERY SHARP CUTTING THE PALM OF HIS RT HAND WOUND WAS CLOSED WITH 5 SUTURES T E5TANUS TOXOID GIVEN RETURNED TO DUTY

I NAME WAS REMOVING POWER LINE HE WAS CUTTING NYLON STRAP WITH A KNIFE THE KNIFE SLIPPED OFF NYLON STRAP & CUT INTO I NAME LEFT THIGH

EMPLOYEE WAS SHOVELING SAND UNDER A CONVEYOR, TIWISTED AND INJURED BACK. SCIATIC NERVE WAS PINCHED AND CAUSED PAIN AND INFLAMATION IN LOWER BACK AND RIGHT LEG.

REPAIRING CYLINDER ON PLANT.DRIVING PIN INTO CLEVIS ON CYLINDER.DARK,COULDNT SEE WELL CAUSING FINGER TO BE DRIVEN IN CLEVIS.

USING A HAMMER PUNCH SMASHING FINGER WITH HAMMER.HE WAS INSTALLING A PIN AT THE TIME.FINGERNAIL HAD TO BE REMOVED AND TWO STITCHES PUT IN.

EMPLOYEE WAS US3NG PRY BAR TO CLOSE GATE WHEN BAR SLIPPED AND EMPLOYEE FELL BACK INTO "I" BEAM, HURTING HIS BACK.

TIGHTENING BOLT8 ON NEW PLANT CONTRUCTION, STRAINING LOWER BACK.

WORKING ON SCRE9N AND JACK SLIPPED.

INJ RAISING MOT2R ON CABLE WITH BLOCK & TACKLE AND WAS HOLDING CABLE AWAY FROM SIDE OF STORAGE BIN WHEN THUMB BECAME CAUGHT IN PULLEY ON CABLE.

REMOVING DECK ON 5X14 DIESTER VIB. SCREEN WITH SLEDGE HAMMER WHEN HIS HAND SLIPPED GITTING HIS FINGER CAUGHT BETWEEN HANDLE AND CABLE. BROKEN INKEX FINGER ON RIGHT HAND.

SCRAPING & PAINTING UNDER SCALES IN VERY CLOSE QUARTES-APPARENTLY WAS INJURED FROM A PINCHED NERVE IN KNEE CAUSING SENESATION OF BEING ASLEEP. DR. SAYS IT IS A PINCHED NERVE.

LOOSENING GREASE PLUG ON LOADER,HAD FOOT IN LUG OF TIRE STEPPED ON WRENCH AND FELL.

A 3/4" EYE BOLT WAS USED IN LIFTING A SECTION OF STEEL BIN WITH CHAIN FALLS FOR PAINTING OF BIN, EYE BOLT LOOKED GOOD AND BIN SECTION WAS LESS THAN 1000 POUNDS IN WEIGHT, NO CLEAR REASON FOR B OLT TO BREAK