Buscar en el registro

Un atascamiento en la boquilla #3 de la BC-M cuando encuentra que tiene unas piedras obtruyendo, una procede a utilizar barra para desalojar la piedra. Realizando un tipo de apalancamiento ejerce presión sobre la barra en direccion hacia el cuando de momento esta se va en blanco, lo que hace que la mano derecha choque con la pared del bajante.

An employee was measuring silo levels, when the measuring tape got caught & employee used a long bar to move the part that was stuck. When the tape was freed, employee's right hand moved hitting the side of the silo opening causing a laceration in employee's right little finger joint. Employee received 4 sutures.

Employee was cleaning a conveyor belt's transition bellow the conveyor pushing accumulated material with a bar, the bar was pushed by the material causing it to slip, the employee tried to grab the bar and it pinched left middle finger with a ladder causing a cut.

The employee was installing bricks inside the kiln and adjusting them with a brick hammer. During the process, he hold a brick with his left hand and finger hammer the tip of the index finger. First Aid was provided in the dispensary and was sent to a Hospital, where four stitches were taken to the base of his left index finger nail. The employee returned to work.

EE was performing cleaning duties with an iron bar at belt conveyor # 3. Accidentally the iron bar touched the belt. After this action the iron bar pulled his arm towards the conveyor. His right ring finger was pinched between the belt and conveyor roller.

EE was performing cleaning duties on a clinker bin discharge with a small chipping hammer. After a while he began to feel back pain.

EE was performing cleaning duties at Conveyor M. After a while he took a piece of pipe that he found on the floor to clean the conveyor. Suddenly the pipe, that had a ragged edge, slipped on his hand causing him an open wound.

While opening a 5 gallon paint can with a retractable knife EE accidentally cut his left index finger with the knife causing him an open wound

Employee was holding a steel bar while a coworker hit it with a sledgehammer. During one of the swings the sledgehammer did not hit the rod dead center and bounced of the rod hitting him above his lips.

EE WAS TRYING TO ALIGN TWO PIECES OF BRACING TOGETHER. HE WAS USING A SMALL MALLET WITH WHICH HE HIT HIMSELF ON HIS LEFT HAND, SUSTAINING AN OPEN LACERATION ON HIS LEFT INDEX FINGER.

EE WAS CUTTING BRUSH WEEDS WITH A MACHETE IN OUR TREE BREEDING AREA. DURING ONE OF HIS SWINGS OF THE MACHETE IT GOT STUCK WITH SOME OF THE BRUSH. WHEN HE PULLED BACK HE ACCIDENTLY HIT THE BACK OF HIS LEFT HAND, NEAR HIS MIDDLE FINGER, WITH THE BLUNT SIDE OF THE MACHETE CAUSING AN OPEN WOUND.

EE WAS SHOVELING CEMENT DUST THROUGH A HOLE ON THE METAL CASING OF A SCREW CONVEYOR. SUDDENLY THE SHOVEL SLIPPED FROM HIS HANDS, HIT THE SCREW CONVEYOR AND REBOUNDED HITTING HIS UPPER LIP.

THE EMPLOYEE LEAN OVER A SCREW CONVEYOR CASING TO TIGHTEN A SCREW, AND FELT A PAIN IN HIS RIGHT SIDE.

WHILE INSTALLING THE LINERS IN THE MILL #11. HE SLIP, AND THE HYDRAULIC JACK HE WAS USING PINCH HIS MIDDLE AND RING FINGER OF HIS LEFT HAND.

THE EE WAS STANDING ABOUT 10'FROM ANOTHER EE THAT WAS USING SLEDGE HAMMER TO INSTALL THE LINERS IN THE MILL #11. WHEN A SMALL PIECE OF METAL FLEW & INCRUSTED ITSELF IN THE LEFT SIDE OF HIS NECK.

INJURED AND CO-WORKER WERE INSTALLING A SEPARATOR ROTOR IN CEMENT MILL #12. THEY WERE PUSHING THE ROTOR WITH AN HYDRAULIC JACK AND AN IRON PIPE. WHEN THE ROTOR FELL INTO PLACE THE IRON PIPE SL IPPED FROM THE ROTOR AND HIT HIM IN THE ABDOMINAL AREA.

EE WAS TIGHTENING A SCREW ON A AIR COMPRESSOR WHEN HE FELT A SHARP PAIN ON HTE LEFT SIDE OF HIS BACK.

EMPLOYEE WAS CLEANING THE ALKALI BY PASS AND RESTRICTORS AREA AT THE PREHEATER TOWER STRIKING AN IRON BAR WITH A SLEDGE HAMMER. AFTER A FEW HOURS HE BEGAN TO FELL PAIN IN HIS BACK AND RIGHT SH OULDER.

EE WAS CLEANING THE ALKALY BY PASS AT THE PREHEATER TOWER WITH AN IRON BAR. AFTER A WHILE THE BAR SLIPPED FROM HIS HAND AND WHEN HE TRIED TO GRAB THE BAR HE PINCHED HIS RIGHT LITTLE FINGER AGA INST THE BAR AND THE POTHOLE BOARDER.

EE AND OTHERS WERE OVERTURNING A BUCKET ELEVATORCHAIN WITH STEEL PIPES. SUDDENLY THE CHAIN SLIPPED AND FELL INTO IT'S ORIGINAL POSITION CAUSING HIM BACK PAIN DUE TO THE FORCE AGAINST THE PIPE.

EMPLOYEE WAS HAMMERING AN EXTENSION BOOM ON A FINGERLIFT TO DISLODGE IT WHEN A PIECE OF METAL FLEW INTO HIS LEFT EYE.

EE WAS REMOVING BRICKS WITH AN IRON BAR AT KILN #6. SUDDENLY HE LOST HIS BLANACE AND FELL TO THE FLOR HITTING HIS LEFT LEG WITH A BRICK.

EMPLOYEE WAS REMOVING BRICKS AT KILN WITH A CHIPPING HAMMER. AFTER AWHILE HIS LEFT HAND SLIPPED FROM THE EQUIPMENT AND ACCIDENTLY HIS LEFT RING FINGER WAS HIT BY THE CHIPPING HAMMER.

EMPLOYEE WAS PERFORMING MECHANICAL DUTIES AT BUCKET ELEVATOR #11. THE EMPLOYEE WAS HOLDING A WHEEL AS LONG AS A PARTNER WAS HITTING THE WHEEL WITH A SLEDE HAMMER. ACCIDENTLY THE SLEDGE HAMMER SLIPPED FROM THE WHEEL AND HIT EE'S HARD HAT CAUSING HIM A CONTISION AND A SMALL WOUND.

EE WAS PERFORMING CLEANING DUTIES WITH ANIRON BAR ON THE SECOND FLOOR AT THE CRUSHING PLANT. ACCIDENTALLY HE HIT A HANDRAIL WITH HIS LEFT LITTLE FINGER CAUSING HIM AN OPEN WOUND.

EE WAS SCRAPING A RAW MILL WALL WITH A SHOVEL. ACCIDENTALLY HE HIT A COLUMN WITH HIS LEFT ELOBW CAUSING PAIN AND INFLAMMATION. THE EE REPORTED THE ACCIDENT ON 2-28-01.

EMPLOYEE WAS REPAIRING A RAW MILL HYDRAULIC CYLINDER WITH ANOTHER EMPLOYEE. HE WAS USING A 36" WRENCH TO FIX THE CYLINDER. WHILE TIGHTENING A BOLT, THE WRENCJ BROKE AND THE EMPLOYEE LOST HIS BALNCE CAUSING HIM BACK PAIN.

EE WAS DISLODGING A BUILDUP IN THE TRESTRICTOR AREA OF OUR PREHEATER TOWER. HE WAS HOLDING A STEEL BAR WHILE A CO-WORKER WAS HITTING IT WITH A SLEDGEHAMMER. DURING ONE OF THE SWINGS IF THE SLEDGEHAMMER, HIS CO-WOKER DIDN'T STRIKE THE BAR SOLIDLY ALLOWIN GTHE SLEDGEHAMMER TO TRAVEL PAST THE END OF THE BAR. WHEN HIS CO-WORKER PULLED THE SLEDGEHAMMER BACK HE NICKED EE'S NOSE.

EE WAS REPAIRING THE COOLING WATER SYSTEM AT CEMENT MILL #11. WHEN HE WAS LOOSENING A NUT THE WRENCH SLIPPED FROM THE NUT CAUSING HIM BACK PAIN AND A RIGHT HAND TRAUMA.

EE WAS REMOVING A PINION FROM A TRANSMISSION SHAFT USING A SLEDGE HAMMER. WHEN HE HIT THE PINION WITH THE SLEDGE HAMMER A PIECE OF METAL DISLODGED AND BECAME EMBEDDED IN HIS LEFT LEG.

EE WAS MOVING A STONE WITH AN IRON BAR AT HAMMERMILL #1. SUDDENLY THE IRON BAR SLIPPED FROM THE STONE AND PINCHED HIS LEFT INDEX FINGER BETWEEN THE IRON BAR AND THE STONE.

EE WAS PERFORMING CLEANING DUTIES AT SPRAY TOWER #1. WHILE HE WAS HOLDING AN IRON BAR OUTSIDE THE SPRAY TOWER, MATERIAL FELL OUT FROM THE TOWER PINCHING HIS LEFT RING FINGER BETWEEN A STONE AN D THE IRON BAR.

EMPLOYEE WAS HAMMERING A PIN INTO A CHAIN LOCATED AT CEMENT MILL 11 WITH A SLEDGE HAMMER. SUDDENLY, THE SLEDGE HAMMER SLIPPED OVER THE PIN CAUSING HIM TO STRIKE HIS LEFT ELBOW WITH A HOIST CHA IN THAT WAS HOLDING ANOTHER CHAIN.

EE WAS PERFORMING ELECTRICAL REPAIR DUTIES AT CRANE #2. WHEN HE WAS CLEANING AN ARCH SHIELD, HE ACCIDENTALLY PUNCTURE HIS LEFT THUMB WITH A KNIFE HE WAS USING TO CLEAN THE EQUIPMENHT CAUSING A N OPEN WOUND.

EMPLOYEE WAS CLEANING THE ACCUMULATED MATERIAL ON THE SPRAY TOWER #2 OUTSIDE THE MANHOLE WITH ANIRON BAR. SUDDENLY MATERIAL FELL OVER THE BAR. THIS PULLED THE BAR AGAINST THE MANHOLE AND PINCHED HIS RIGHT INDEX FINGER CAUSING AN OPEN WOUND.

EE WAS CLEANING THE RAW MILL TRIPLE GATE WALLS WITH AN IRON BAR. WHEN HE WAS TRYING TO STICK THE BAR IN THE CLAY THE BAR SLIPPED OVER THE CLAY. THIS ACTION CAUSED THE BAR TO COME AGAINST HIS F ACE STRIKING ABOVE HIS LEFT EYE-BROW.

EE WAS CLEANING A FUNNEL SECTION IN THE HAMMER MILL #3 WITH AN IRON BAR. HE STUCK THE BAR IN THE CLAY, WHEN HE PUSHED IT FORWARD HE PINCHED HIS LEFT MIDDLE FINGER BETWEEN THE BAR AND THE METAL STRUCTURE OF THE FUNNEL CAUSING HIM AN OPEN WOUND.

EE WAS REMOVING A UNION FROM A FORKLIFT DRIVE SHAFT. HE POSITIONED THE SHAFT ON A WORK TABLE AND STRUCK IT WITH A HAMMER WHICH CAUSED THE SHAFT TO GIRATE AND PINCH HIS RT THUMB.

EE WAS INSTALLING A FITTING ON A HOSE USING AN ASSEMBLING MACHINE. WHEN HE WAS PUSHING THE HOSE TO MATE IT WITH THE FITTING, THE FITTING SLIPPED OFF THE VISE. THIS CAUSED HIS LEFT HAND TO SLIP OFF THE HOSE VISE ASSEMBLY AND GET CAUGHT BY THE VISE.

EE WAS CLEANING KILN#6 RESTRICTORS AREA WITH AN IRON BAR THROUGH A PORT HOLE. WHILE HE WAS HOLDING THE BAR MATERIAL FELL ON THE END OF THE BAR INSIDE THE RESTRICTOR CAUSING THE OTHER END TO LI FT UP AND STRIKE HIS CHIN CAUSING AN OPEN WOUND Y

EMPLOYEE WAS LOOSENING A NUT FROM GRINDER TO REPLACE THE DISC WHEN THE WRENCH SLIPPED OFF THE NUT AND HIS RIGHT WRIST STRUCK THE GRINDER'S GUARD

2 EMPLOYEES WERE CLEANING THE PREHEATER TOWER'S RESTRICTORS WITH A STEEL ROD AND A SLEDGE HAMMER. INJURED WAS HOLDING ROD WHILE OTHER WAS HAMMERING IT. BOTH WERE POSITIONED ON THE SAME SIDE OF THE ROD. ON THE LAST SWING EE MADE HE FAILED TOHIT THE ROD DEAD CENTER WHICH CAUSED THE SLEDGE-HAMMER TO CONTINUE ITS TRAVEL AND HIT INJURED ON THE RIGHT SIDE OF HIS CHEST.

EMPLOYEE WAS REPAIRING THE RAYMOND MILL MACHINE WITH EMPLOYEE. WHILE EMPLOYEE WAS HOLDING A COUPLING, EMPLOYEE ACCIDENTALLY HIT EMPLOYEE'S LEFT RING FINGER WITH A SLEDGE HAMMER HE WAS USING TO DRIVE THE COUPLING INTO PLACE.

EMPLOYEE WAS SHARPENING THE EDGE OF A METAL PLATE WITH A FILE. HE WAS FILING AGAINST THE SHARP EDGE OF THE PLATE WHEN THE FILE SLIPPED OFF THE END OF THE PLATE CAUSING HIS RIGHT HAND THUMB TO STRIKE THE EDGE OF THE PLATE.

EE WAS LOOSENING SCREWS ON ROLLER MILL'S 3 ROLLER WHEN THE WRENCH HE WAS USING SLIPPED WHICH CAUSED HIM TO LOSE HIS BALANCE AND FALL. WHEN HE LANDED HIS RIGHT LEG STRUCK A SHARP METAL ON THE R OLLER ASSEMBLY CAUSING A WOUND IN HIS RIGHT LEG.

EE WAS SWEEPING AND SHOVELING CEMENT IN THE CEMENT MILL AREA. THE MOVEMENT OF HIS ARMS AND HANDSCAUSED THE CUFFS OF THS GLOVES TO RUB AND LACERATE BOTH WRISTS. HIS SWEAT MIXED WITH CEMENT AGGRAVATED THE INJURY.

EE WAS CLEANING BELT CONVEYOR 3 & 4 TRANSITION POINT WITH A STEEL ROD WHEN HIS LEFT WRIST BEGANTO BOTHER HIM.. HE RECD 1ST AID TREATMENT IN OURDISPENSARY. ON 11/6/97 HE RETURNED TO THE DISPEN SARY WITH IHS LEFT WRIST SWOLLEN & WAS SENT TO STATE INSURANCE FUND.

EE WAS HAMMEIRNG A STEEL PLATE WHEN HE FELT A OBJECT STRIKE HIS LEFT WRIST. EE WAS SENT TO THESTATE INSURNACE FUND ON 10/21/97 FOR MEDICAL TREATMENT.

EE WAS REMOVING BUCKET ELEVATOR 9'S CHAIN FROM THE MOTOR AND SPEED REDUCTION ASSEMBLY. WHEN HE PULLED THE CHAIN, THE BACK SIDE OF HIS RIGHT WRIST STRUCK THE ASSEMBLY'S SPOKET.

EMP WAS HAMMERING WITH A SLEDGEHAMMER WHILE PERFORMING CLENAING DUTIES IN CEMENT MILL AREA WHEN HE FELT A SHARP APIN IN BACK.