Buscar en el registro

Employee was pulling on tire chain. Employee was using a tee bar with a hook on the end to pull the chain in place. The employer was pulling hard and the hook slipped of the chain causing the employee to fall on back

Removing small center shaft on loader with come-along. Shaft got hung up on bolt and slid to strike forehead. Cut on forehead, cleaned and placed band-aid on cut. Sent to care center to just have them evaluate. They place two stitches and returned EE to work with no restrictions.

Employee was removing a bolt on a 330CL Excavator to change out attachments and when the bolt broke loose his left thumb was smashed between the wrench and the boom. His left thumb began to swell after a while. A co-worker and the employee talked and decided to be safe to have his left thumb looked at.

During disassembly of transmission pump, a hammer and punch were used to remove the shaft from the housing. On the third strike a chip flew off the punch and struck the upper lip. Employee requested a band-aid and declined a trip to the doctor.

Employee was assisting with the assembly of the upper frame of a Pegson cone crusher. A driving maul tool and 20 pound sledge were being used to help drive the concave wedges in place as a metal chip struck the employee in the left hand. The employee was taken to a local healthcare facility and stitches were required to treat lacerations in his left index & middle fingers.

EE was working on vehicle 22-311. While working on suspension he heard a popping type sound. He immediately pulled his left arm away from bolts being tightened. The leaf springs may have shifted. Springs were not under load.

Prying on a bearing rack with a heelbar inside a gear box. The heelbar slipped which caused my right forearm to hit the gear box housing. The edge of the housing was fairly sharp.

While driving a stake into a wattle, employee's hand & stake moved causing sledge hammer to hit his left hand.

Driving a bushing with a chisel when a piece of the chisel broke off and punctured left knee.

Installing safety latch on wire rope hook using screw driver, and screw driver slipped and went across knuckle on left index finger.

BACKING OFF BRAKE ADJUSTMENT NUT, WRENCH SLIPPED AND HIT HIM IN THE RIGHT EYE CUTTING UPPER & LOWER LID, KNOCKING OFF SAFETY GLASSES.

PLACING DIFFERENTIAL IN ROCK TRUCK FELT SOMETHING PULL IN LEFT SHOULDER WHILE PULLING WRENCH.

OPERATING CORDLESS DRILL, AIRTOOLS & HAMMER, HE STARTED EXPERIENCING SHARP PAIN IN RIGHT LOWER ELBOW.

EE PLACED VALVE IN VICE, USED WRENCH TO REMOVE FITTING WHILE PULLING THE RIGHT HAND WAS CRUSHED BETWEEN VALVE AND VICE.

EE WAS TRYING TO STRAIGHTEN A RADIATOR HOOD OFF OF A 988F. WHILE HE WAS HITTING A PIECE OFF THE HOOD WITH A HAMMER, IT CAME LOOSE STRIKING HIM ON THE RIGHT INDEX FINGER.

EE WAS SHOVELING OUT SAND THAT HAD BUILT UP INSIDE THE GRIZZLEY TUNNEL. HE STOOD DOWN UNDER A BELT AND CAUGHT HIS LEFT SHOULDER ON A STEEL BAR SUPPORT.

LIFTING GENERATOR HALF AND SHACKEL SLIPPED AND LET PART FALL ABOUT 4" AND SMASHED 2 FINGERS ON LEFT HAND.

EMPLOYEE WAS INSTALLING A BEARING ON A SPINDLE WITH HAMMER AND PUNCH. A SLIVER OF METAL CAME OFFOF THE PUNCH. AND IMBEDDED IN LEFT FOREARM.

WHILE LIFTING A BAR NEEDED TO DISLODGE A ROCK FROM A CHUTE, EMPLOYEE PULLED A MUSCLE IN HIS LOWER BACK.

CHANGING TOOTH ON DRAGLINE BUCKET. WHILE DRIVING TOOTH OFF WITH A 6 LB HAMMER A CHIP BROKE OFF OF TOOTH AND STRUCK THE RIGHT KNEE. SLIVER OF METAL WAS IMBEDDED INTO THE SOFT TISSUE.

PULLING CABLE ON DRAGLINE USING A 3 FOOT PRY BAR TO PRY CABLE FROM SHEAVE.

EE WAS ADJUSTING A ROLLER WITH A PIECE OF ANGLE BAR. THE BAR SLIPPED AND PUNCTURED HIS RIGHT INDEX FINGER.

HOLDING PUNCH & HAMMER GLANCED OFF PUNCH AND HIT HAND.

EE WAS USING A FENCE POST HAMMER TO INSTALL A GRUND ROD AT A PORTABLE FEEDER. WHILE DRIVING THE GROUND ROD, HE LIFTED THE HAMMER TOO HIGH AND ON THE NEXT STROKE MISSED THE ROD AND LET THE HAMM ER FALL ON HIS FOOT.

LABORER WAS CUTTING FLASHING WITH A SHEETROCK KNIFE. THE KNIFE SLIPPED AND CUT HIS LEFT LEG ABOVE KNEE HE RECEIVED THREE STITCHES.

FINISHING CONCRETE USING HAND TOOLS STARTED NOTICING TINGLING IN FINGERS

CHANGING LINERS. PIECE OF METAL HIT WORKER IN LEG.

A ROCK GOT STUCK IN JAW ON MAIN PLANT AND EMPLOYEE WAS USING A PRY BAR AND ANOTHER ROCK CAME DOWN AND HIT THE BAR, AND HIS FINGERS GOT SMASHED BETWEEN THE BAR AND THE SIDE OF METAL PLATE ON IN SIDE JAW.

WRENCH SLIPPED ALLOWING FINGER TO CONTACT METAL TAB WELDED TO TRAILER

EMPLOYEE WAS PUTTING TIRE ON A GRADER. HE WAS LIFTING TIRE WITH A BAR AND THE TIRE ROLLED ON THEWHEEL CAUSING HIM TO LOOSE HIS FOOTING AND STRAIN HIS BACK IN ATTEMPT TO CATCH THE TIRE.

EE WAS WORKING ON THE STACKER CHUTE CUTTING THE LINER WHEN THE KNIFE SLIPPED & HE CUT HIS LEG

WHILE DRIVING OUT A TILT CYLINDER PIN ON A 988D WHEEL LOADER WITH AN EIGHT POUND HAMMER, THE HAMMER SLIPPED AND GLANCED OFF THE PUNCH AND HIT HIS LEFT ARM. THE INCIDENT HAPPENED ON 8-2-99, BUT WAS NOT REPORTED TO SUPERVISOR UNTIL 8-4-99 BECAUSE HE FELT IT WAS NOT THAT BAD OF AN INJURY.

WHILE CLEANING THE CRUSHER OUT WITH A WATER HOSE. THE HOSE WAS TIED TO THE STRUCTURE WITH PLASTIC WIRE TIES, EE CUT ONE OF THE TIES WITH A POCKET KNIFE, WHEN IT CUT THROUGH THE HOSE, SLID TOW ARD EE HIS HAND CAME BACK AT HIS ARM WITH THE KNIFE, CUTTING HIS ARM.

PULLY WAS STUCK AT SAND TUNNE. EE WAS TRYING TO MAKE PULLY TURN BY PUTTING A PIPE WRENCH ON THE SIDE OF THE PULLY & TRIED TO BREAK IT LOOSE. THE2ND TIME HE TRIED IT CAME LOOSE & HIS HAND GOT SMASHED BETWEEN THE PIPE WRENCH & THE PAN/PULLY

WAS HOLDING A BAR, AND A PIECE OF METAL CAME OFF WHEN THE HAMMER HIT IT AND LANDED IN THE BACK OF LEFT HAND & CUT IT.

EE WAS MOUNTING A TRUCK TIRE WHEN TIRE BAR SLIPPED OFF RIM AND HIT RIGHT KNEE.

EE ORIGINALLY INJURED HIS BACK ON 4-25-96. HE IS CURRENTLY WORKING THE PRIMARY CRUSHER JOB UNDER FULL TIME MODIFIED DUTY. ON 4-7-98 EE FELT SOMETHING SLIP IN HIS BACK WHILE LEANING OVER THE GU ARD RAIL AT THE GABION PLANT JAW CRUSHER. EE HAD A BAR AND WAS TRYING TO UNPLUG THE JAW. THIS INJURY IS A FLARE UP OF THE ORIGINAL INJURY PER DOCTOR REPORT. WE WERE FIRST NOTIFIED OF THIS INJ

WAS PRUNING TREES AND PLANTS AT C.M. SYAR'S HOUSE. WHEN PULLING ON IVY, THE VINES BROKE AND HAND AJMED INTO SHEARS HELD BY OTHER HAND.

WHIE WORKING ON THE SCREEN WITH EE HIS HAND SLIPPED OF THE WRENCH AND HIT A NUT CUTTING HIS LITTLE FINGER.

HE HIT HIS LEG WITH A SLEDGE HAMMER WHILE REMOVING A BIG ROCK FROM JAW CRUSHER.

EE INHALED DUST THRU BROKEN RESPIRATOR. EE WAS CLEANING UNDER PRIMARY CRUSHER. HE WAS COUGHING EXCESSIVELY. THE FOREMAN TOOK HIM TO THE HOSPITAL WHEN EE STARTED COUGHING UP BLOOD.

THE EYE BOLT IN THE METAL CLAMP BROKE WHILE SPLICING THE BELT. THE BELT CLAMP CAME LOOSE AND HIT HIM ON LEFT LEG AND FOOT.

WHILE CLEANING OUT BUILT UP MATERIAL IN THE 3' CRUSHER WITH THE DIGGING BAR HE MISSED THE SHUT AND CUT HIS LEFT LITTLE FINGER.

WHILE USING A HYDRAULIC JACK TO PRESS OUT A "U" JOINT OUT OF A DRIVE LIEN THE JACK SLIPPED & BOUNCED OFF FRAME HITTING EMPLOYEE IN THE RIGHT SIDE OF THE HEAD CAUSING A CUT OVER THE RIGHT EYE

WHILE REPAIRING CRUSHER USING SLEDGE HAMMER TO POUND IN WEDGES A PIECE OF METAL FLEW UP CUTTING FINGER.

WHILE BEATING ON A CUTTING EDGE TO MAKE IT FIT PROPERLY ON A LOADER, A PIECE OF METAL FLEW OFF AND HIT HIS LEFT CHEEK.

WHILE WORKING ON THE ERECTION OF WATER TANK.HIT A BOARD WITH A NAIL IN IT. THE BOARD FLEW BACK THE NAIL IN THE BOARD PIERCED RIGHT EAR LOBE. DID REQUIRE TREATMENT. AFTER THE EAR WAS STITCHED UP EMPL RETURNED TO WORK WITHOUT ANY RESTRICTION

USING AN ALIGNING BAR TO PLACE WEAR PLATE IN PUGMILL AT ASPHALT PLANT #2. THE PLATE SLIPPED OFF THE BAR AND THE PLATE CAME DOWN ON THUMB OF LEFT HAND.

EE WAS POUNDING ON SCREEN DECK AND SOMETHING GOT IN HIS EYE.

PUT GIZZLY BAR ON SHOULDERS TO LIFT AND FELT A STRAIN IN LOWER LEFT NECK.