Buscar en el registro

On August 23rd at 9:45 the conditions are good, sunny outside around 92 degrees. Work area was well lit with little debris on the ground. EE was working on the hammer mill crusher trying to mock up the grates for repairs. When the soft sling EE was using wasn't choked all the way slid off center smashing EE's hand between the hammer mill crusher frame and the grate.

Individual was attempting to clear what was thought or appeared to be an obstruction on a conveyor belt roller. Individual used the handle of a hammer to knock away what appeared to be mud but was a hole in the roller. The handle was caught in the hole and slammed EE's hand into the conveyor frame.

While using sledge hammer to close crusher a slice of metal flew off of steel and struck employee in chest.

Strained back working with sledge hammer on plant. Employee did not want to seek medical care until 27July11.

Working in shop stabbed himself with screw driver.

Employee was attempting to open rail-hopper car gate. The tool he was attemting to use slipped causing him to fall hitting his head. He was taken to ER - given a CAT scan and released to work the following day.

Employee was pulling on a wrench & hurt his back.

EE WAS PRYING WITH A BAR, THE BAR SLIPPED AND HIT HIM ON THE LEFT TEMPLE.

EMPLOYEE WAS CUTTING A PIECE OF CONVEYOR BELT WITH A BOX KNIFE AND CUT HIS HAND.

EMPLOYEE WAS REACHING FOR A 3/4" RATCHETT. IT FELL HITTING HIM ABOVE HIS RIGHT EYE.

EMPLOYEE WAS HELPING REPLACE A WEAR PLATE ON A LOADER BUCKET. WHEN HE HIT THE PLATE WITH A SLEDGE HAMMER, A PIECE CHIPPED OFF THE PLATE AND HIT HIM IN THE CHEST.

EE WAS HITTING BUCKET TOOTH ON A FRONT END LOADER WITH A SLEDGE HAMMER AND A PIECE CHIPPED OFF THE TOOTH HITTING HIS LEG.

EE WAS HOLDING A WEDGE WHILE ANOTHER EE HIT IT WITH A SLEDGEHAMMER. HE GOT HIS FINGER BETWEEN THE WEDGE AND THE SLEDGEHAMMER AND SMASHED THE TIP OF HIS RING FINGER.

EE WAS CUTTING A SECTION OF CONVEYOR BELT WITH A BOX KNIFE. THE KNIFE CAME APART AND THE BLADE CUT HIS FINGER.

EE WAS REPLACING A WHEEL ON A TRUCK AND HURT HIS BACK PULLING ON A WRENCH. HE CONTINUED TO WORK UNTIL11-07-01 WHEN HE BEGAN LOSTING TIME FROM WORK.

EE CUT A COTTER PIN WITH A PAIR OF PLIERS, THE CUT END OF THE PIN FLEW UP AND EMBEDDED IN HIS EYE.

WRENCH SLIPPED-EE HIT TOP OF HAND ON METAL BRACKET. CUT TOP OF HAND.

EMPLOYEE WAS REMOVING A RUBBER GROMMET OUT OF A HYDRAULIC HAMMER WITH A SCREWDRIVER WHEN IT SLIPPED AND JABBED HIS LEFT FOREFINGER.

EE WAS SWINGING A SLEDGE HAMMER & FELT PAIN IN HIS BACK THAT CONTINUES TO HURT. Y

EMPLOYEE WAS USING A BAR TO OPEN A RAILCAR DOOR AND WHEN HE PULLED ON THE BAR HE FELT A PAIN IN HIS LOWER RIGHT ABDOMEN.

EE WAS CLEANING THE CAB OF HIS SCRAPER WITH A SMALL BRUSH & GOT A SMALL PARTICLE OF ROCK IN HIS EYE.

EE WAS WORKING ON A FRONT END LOADER IN A BENT OVER POSITION. HIS BACK BEGAN TO HURT AND CONTINUED TO GET WORSE AFTER WORK.

EMPLOYEE WAS DOING CRUSHER REPAIR AND A HYDRAULIC JACK FELL AND MASHED HIS THUMB.

EE WAS REMOVING THE CAP ON THE WATER TRUCK SPRAY BAR WITH A LARGE WRENCH AND HURT HIS BAKC WHEN HE PULLED ON THE WRENCH.

EMPLOYEE WAS PRYING ON THE CRUSHER HAMMERS WITH A BAR. HE RAISED THE BAR AND PINCHED HIS THUMB BETWEEN THE BAR AND THE EDGE OF THE CRUSHER.

EE WAS HITTING ON A BIN WITH A SLEDGE HAMMER AND A PIECE OF STEEL CHIPPED OFF AND WENT INTO HIS EYE HE DID NOT GO TO A DR UNTIL 10-5-92 AND DID NOT REPORT THE INJURY UNTIL 10-12-92.

EMPLOYEE WAS HITTING THE BUCKET OF A SCRAPER WITH A SLEDGEHAMMER WHEN A SMALL ROCK FLEW UP AND HIT HIM IN THE EYE.

EMPLOYEE WAS PULLING ON A C CLAMP, TH CLAMP PULLED LOOSE AND HE HIT HIS HAND ON THE EDGE OF THE FRAME.

EMPL WAS HITTING CHUTE WITH SLEDGE HAMMER & PULLED USCLE IN NECK.

EMPL HITTING CHUTE WITH SLEDGE HAMMER ,SLIPPED AND FELL BREAKING A RIB.WENT TO DR 5-24-91.

EMPLOYEE WAS MOPPING A FLOOR WHEN HER ELBOW BEGAN TO HURT. INJURY WAS REPORTED ON 10-23-89/WENT TO DR. ON 10-26-89-NO RX. BEGAN PHYSICAL THERAPY ON 11-1-89.

EMPLOYEE WAS USING A HAMMER TO STRAIGHTEN A BENT BRAKE DRUM AND A PIECE OF STEEL CHIPPED OFF THE DRUM PIN AND IMBEDDED IN HIS ARM.

EMPLOYEE AS CLEANING OFF A PIECE OF STEEL TO MARK IT WITH A PENCIL, WHEN HE SCRAPPED THE DIRT OFF A SMALL PIECE CHIPPED OFF AND HIT HIS EYE.

EMPLOYEE WAS USING A BAR TO PRY UP THE DRIVE SHAFT ON A TRUCK,THE BAR SLIPPED AND THE SHAFT FELL ON HIS LEFT HAND.

EMPLOYEE WAS DR3VING A STEEL PIN WITH A HAMMER AND A SMALL PIECE OF STEEL CHIPPED OFF THE PIN STRIKING THE EMPLOYEE IN THE LEG. STEEL CHIP WAS EMBEDDED IN LEG-DOCTORS RECOMMENDED THAT THE CHI P BE LEFT IN EM1LOYEE'S LEG, HOWEVER, APPROX. 30 DAYS LATER THE CHIP BEGAN TO CAUSED PROBLEMS SO IT WAS REMOVED.

EMPLOYEE WAS PRYING ON SHAFT SEAL WITH BAR BAR SLIPPED AND HIS HND HT EDGE OF SHAFT KEYWAY CUTTING HIS FINGER