Buscar en el registro

At or around 6:50 pm on 10/23/2013, a DuPont Operator was in the process of clearing an obstruction from the turn table with an alignment bar when the employee's thumb was pinched between the alignment bar and structure. The EE was transported to the hospital for treatment.

On Thursday 07/22/10 at 1:45 P.M., a mechanic pinched the ring finger of the right hand while replacing belts on a 600 HP pump/motor assembly. The mechanic was using an 18" aluminum pipe wrench to turn the 48" diameter sheave to roll the belts on when the mechanic's gloved hand came in contact with the guard support structure pinching the ring finger.

On 05/25/10, a mechanic replaced the MXWM domestic water pump. He stood up to reach for a pipe wrench & felt a sharp pain in his back. Evaluation by the plant Dr. was a pulled muscle. Injury was classified as a FAC. On 08/04/10, MRI revealed emp. has a herniated disc. Emp. will receive further evaluation. On 08/11/10, this case was re-classified as an OER-RWC.

CONTRACT MECHANIC WAS ADJUSTING TRUNION ROLLERS WITH RATCHET WRENCH. WHILE TIGHTENING NUT THE WRENCH HIT THE HANDRAIL CATCHING MIDDLE FINGER OF LEFT HAND BETWEEN HANDLE AND HAND RAIL. X RAYS S HOWED A HAIRLINE FRACTURE. A METAL PROTECTOR WAS PLACED ON THE FINGER FOR PROTECTION FROM BUMPING AND THE MAN WAS RELEASED TO RETURN TO WORK.

A MECHANIC SUFFERED A SMALL LACERATION TO HIS UPPER LIP WHEN A PRY BAR ANOTHER EMPLOYEE WAS USING SLIPPED. THE LACERATION REQUIRED 4 SUTURES TO CLOSE. THE EMPLOYEE RETURNED TO WORK AT FULL CAPACITY FOLLOWING THE SUTURING.

ON 6-7-93, AT 11AM A MECHANIC PINCHED OFF THE FLESHY TIP OF HIS FINGER (MIDDLE INDEX) WHILE ADJUSTING A CONVEYOR WIPER USING A 15" ADJUSTABLE WRENCH. THE WRENCH SUDDENLY JUMPED AND PINCHED H IS FINGER BETWEEN THE WRENCH HANDLE AND THE PLA TFORM GRATING.

MECHANIC WAS REMOVING GEAR REDUCER AND BEARING FROM ELEVATOR HEAD PULLEY SHAFT. WHIEL WORKING FROLM A LADDER, MECHANIC USED A 30" ALIGHMENT/PRY BAR TO MOVE BEARING ALONG THE SHAFT. THE BAR S LIPPED AS THE MECHANIC PULLED THE BAR TOWARD HIMSELF. THE BAR STRUCK THE MECHANIC, LACERATING HIS UPPER LIP.

REPAIRS IN SCREEN DRIVING PINS OUT OF SPACER H;IT RING FINGER WITH HAMMER

OPERAOTR WAS USING HACKSAW TO REMOVE RESTRAINING CHAIN FROM DREDGE SLEEVE BAND WHEN SAW SLIPPED, CUTTING OPERATORS INDEX FINGER, LEFT HAND THROUGH GLOVE.

EMPL WAS ADJUSTING PACKING FOLLOWER ON 20" DREDGE PUMP 1-1/4" OPEN END WRENCH WRENCH SLIPPED ALLOWING THE R HAND TO STRIKE THE METAL HOSE CLAMP ON THE ADJACENT SEAL WATER SUPPLY LINE THE METAL CLAMP END CUT THROUGH THE LEATHER GLOVE AND INTO THE BACK OF HIS R HAND

WAS STRIPPING ELECTRICAL INSULATION FROM 3/0 CABLE

EMPLOYEE WAS ADJUSTING SQUEEZER ON THE WASH WATER SUPPLY TO SPIRALS ADJUSTABLE WRECH SLIPPED, ALOOWING HAND TO STRIKE THE STRAP BAND CLAMP WHICH PUNTURED THE HAND AT THE THUMB.

OPERATOR WAS PL5CING A 4X4 TIMBETR UNDER 22 IN PIPE TO POSITION IT SO A CABLE COULD BE USED TO LIFT THE PIPE. THE PIPE WAS BEING LIFTED BY A CABLE WITHA HOOK CAUGHT OVER THE END OF THE PIPE. THE HOOK SLIPPE8 DROPPING THE PIPE ON THE END OF A TIMBER. THE TIMBER CAME UP AND STRUCK THE OPERATOR IN THE CHEST

TWO EMPLOYEES W9RE ON THE WORK BOAT ATTEMPTING TO PULL A PONTOON LOOSE FROM THE BANK. THEY WERE USING A 2 INCH MYLON ROPE. WHEN THEY APPLIED POWER, THE ROPE STRETCHED, AND THEN SLIPPED OFF THE BIT AND RECOIL9D INTO THE BOAT CAB THE ROPE STRUCK THEM ON THE LEGS AND ANKLES, CAUSING CONTUSIONS.

TWO EMPLOYEES W9RE ON THE WORK BOAT ATTEMPTING TO PULL A PONTOON LOOSE FROM THE BANK. THEY WERE USING A 2 INCH NYLON ROPE. WHEN THEY APPLIED POWER, THE ROPE STRETCHED, AND THEY SLIPPED OFF THE BIT AND RECOIL9D INTO THE BOAT CAB. THE ROPE STRUCK THEM ON THE LEGS AND ANKLES, CAUSING CONTUSIONS.

A MECHANIC WAS 1OSITIONING A PIECE OF PIPE WITH A COME-ALONG. THE COME-ALONG WAS NEW & HAD NEVER BEEN USED. THE UPPER HOOK ON THE COME-ALONG FAILED & IT FELL ON T HE MECHANICS FINGER BREAKIN G & LACERATING 7HE TIP OF THE FINGER. HIS FINGER WAS SUTURED & PLACED IN A SPLINT.

EMPLOYEES WERE 9EMOVING A PIECE OF 20" DIAMETER BY 40' LONG STEEL PIPE FROM A PILE OF PIPE. A CABLE HOOP WAS PUT IN THE END OF THE PIPE SO THE PIPE COULD BE RAISED. THE INJURED EMP WAS ATTEMPT ING TO SUPPORT 7HE PIPE WITH A PRYBAR WHEN THE HOOK SLIPPED AND THE PIPE FELL. THE PIPE KICKED THE PRYBAR UP AND IT STRUCK HIM IN THE FACE, HIS NOSE AND EYELID WERE CUT AND REQUIRED SUTURES

ELECTRICIAN WAS3TIGHTENING A NUT WITH A RATCHET WRENCH THE WRENCH SLIPPED OFF THE NUT AND HIS HAND HIT A METAL FRAME HIS LITTLE FINGER WAS CUT AND REQUIRED TWO SUTURES

MECHANIC WEDGIN1 APART CLAMP WITH CHISEL.CHISEL STUCK IN PLACE UNDER TENSION.AS HE TRIED TO REMOVE CHISEL,IT RELEASED SUDDENLY AND TWISTED THROUGH HIS HAND.HIS HAND WAS CUT AND REQ 11 SUTURES.

EE WAS USING APOCKET KNIFE TO CUT A SHEET OF RUBBER. THE KNIFE BLADE FOLDED UP & CUT HIM ON T HE THUMB. THE CUT REQUIRED 3 SUTURES.

EMPLOYEE WAS USING A KNIFE TOCUT OFF A SECTION OF HOSE. THE KNIFE SLIPPED ANDCUT HIS LEFT THUMB. THE CUT REQUIRED THREE SUTURES.

OPERATOR WAS USING RATCHET WRENCH TO TURN BOLT. THE RATCHET MECHANISM SLIPPED AND HIS FINGER CAUGHT BETWEEN THE WRENCH HANDLE AND A PIECE OF STEEL. HIS RIGHT RING FINGER WAS CUT AND REQUIRED S IX SUTURES.

ELECTRICIAN USING KNIFE TO STRIP INSULATION OFF WIRE.KNIFE SLIPPED AND HE CUT FOREARM.CUT REQ 2 SUTURES.

EMPLOYEE WAS USING A KNIFE TO CUT A CREDIT CARD. THE KNIFE SLIPPED AND SHE CUT HER LEFT INDEX FINGER. THE CUT REQUIRED TWO SUTURES.

USING HAND HOIST.