Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
EE WAS TIGHTENING A NUT ON SHAKER #52. THE SOCKET SLIPPED OFF OF THE NUT, PINCHING HIS RIGHT PINKY BETWEEN THE RATCHET HANDLE AND SHAKER FRAME.
CREW WAS LOOSENING THE MANTEL ON A CONE CRUSHER.THEY HAD A CHAIN 3/8 GR. 80 TIED TO THE MANTEL &HOOKED TO A LOADER PULLING ON IT. A PORTA-POWER WAS BEING USED IN CONJUNCTION WITH THE CHAIN. TH E PORTA-POWER FAILED BINDING THE MANTEL UP WHICH CAUSED AN OVERLOAD ON THE CHAIN, THE CHAIN BROKE, WHIPPING EE ON THE LEFT SHIN/CALF AREA.
WAS DIGGING PORTABLE #3 CRUSHER TIRES WHEN GRUBBING HOE STRUCK A ROCK STRAINING HIS LEFT WRIST.
EE WAS CUTTING A BOLT NOTCH OUT OF A STRIP OF WIPER RUBBER. HIS LEFT HAND WAS NEAREST TO HIM AND HE WAS PULLING THE KNIFE TOWARD HIM. THE KNIFE SLIPPED RUNNING ACROSS HIS LEFT THUMB AREA LEAVI NG A MULTI LAYERED LACERATION ON THE TOP OF HIS THUMB.
WAS REMOVING A STUCK ROCK FROM #1 BELT OUT OF FEEDERS, EE WAS USING A PRY BAR AND OTHER EE WAS PULLING ON IT. AT THIS TIME HE FELT A MINOR PAIN IN HIS LUMBAR BACK AREA.
EMPLOYEE WAS DOING MANUAL CLEAN UP WITH A HAND SHOVEL HIS ENTIRE SHIFT. HE WOKE UP THE NEXT DAYWITH SOME DISCOMFORT. HE WAITED TO SEE IF HE WOULD FEEL BETTER IN A COUPLE OF DAYS. HE DID NOT SO HE REPORTED IT.
EE WAS LOOSENING NUTS ON SHAKER #57. THE NUT BROKE LOOSE AND PINCHED HIS RIGHT PINKY BETWEEN THE RACHET HANDLE AND THE SHAKER FRAME.
EMPLOYEE WAS USING A BAR TO CLEAN A CHUTE AT THE SAND CLASSIFIER. ON A DOWN STROKE HE STRUCK HIS LEFT PINKY FINGER ON A METAL HOOK USED TO TIE THE CHUTE UP WITH. THIS RESULTED IN A CONTUSION TO THE FINGER THAT WAS ADDRESSED WITH FOUR SUTURES.
EE WAS HITTING PLUGGED SCREEN WITH BRACE HAMMER, HEAD OF HAMMER WENT THROUGH SCREEN OPENING ALLOWING HIS FINGER TO BE PINCHED BETWEEN SCREEN AND HAMMER HANDLE.
EMPLOYEE WAS SWINGING A SLEDGE HAMMER TRYING TO MOVE AN OBJECT. ONE OF HIS SWINGS MISSED HIS TARGET AND HIS RIGHT SHOULDER WAS STRAINED. THIS WAS NOT REPORTED UNTIL 10-31-00.
TWO EE'S WERE REMOVING BUCKET TEETH. INJURED HELD A PUNCH ON THE RETAINING PIN WHILE CO-WORKER SWUNG THE HAMMER. ONE OF THE STRIKES CAUSED A CHIP OF METAL TO FLY OFF AND STRIKE HIM IN THE THIG H. THE METAL PIECE PUNCTURED AND LODGED INSIDE HIS THIGH.
EE WAS LOWERING THE OVERHEAD SHOP DOOR USING THECHAIN & PULLY SUPPLIED AS HE WAS PULLING THE CHAIN HE STRAINED A MUSCLE IN HIS LOWER BACK
CO-WORKER WAS HITTING THE RIPPER SHANK GUARD TO REMOVE IT FROM THE SHANK. ONE OF THE HITS FROM THE 10# STEEL HAMMER CAUSED A PIECE OF METAL TO CHIP OFF & HIT EE IN THE BACK OF HIS LEFT LEG.
EE WAS TRYING TO REMOVE THE CENTER PIN ON THE STABILIZATION BAR ON A CAT D-9L DOZER. POSITIONED UNDERNEATH THE MACHINE, HE BEGAN HITTING ON THE AREA SURROUNDING THE PIN. PRESSURE WAS BEING APP LIED TO THE PIN FROM THE OTHER SIDE BY A PORTABLE HYDRAULIC PRESS. ONE OF THE STRIKES W/ HAMMER HIT CENTER PIN, CAUSING A PIECE TO FLY OFF & HITEE ON CALF AREA. METAL CHIP REMOVED W/3 STITCHE
EE WAS REMOVING AN EXCAVATOR TOOTH BY HITTIJG IT WITH A HAMMER. ON ONE HIT, A PIECE OF METAL FLEW OFF THE TOOTH AND LODGED IN HIS UPPER LEFT ARM.
EE WAS SHIMMING A SUPPORT LEG OF THE CALICHE PLANT. USING A 10LB SLEDGE HAMMER WITH BOTH HANDS SGRIPPING THE HANDLE, HE WOULD SWING AND STRIKE THE SHIM, DRIVING IT IN FURTHER, REMOVING THE PLA NT IN THE SUPPROT LEG. DURING HIS LAST STRIKE, HIS RIGHT HAND THUMBNAIL CAUGHT THE EDGE OF A TIRE, WHICH IS PART OF THE PLANT. WHEN THIS HAPPEN, IT CAUSED HIS THUMBNAIL TO BE PULLED BACK OFF
EE WAS HELPING HIS FOREMAN KNOCK OUT SOME LOADER BUCKET PINS BY STEADYING A SHAFT USED AS A PUNCH MADE OF HIGH TENSIL STEEL. ONE OF THE HITS FROM THE HAMMER CAUSED A PIECE OF METAL TO FLY OFF AND HIT OSCAR IN HIS LEFT FOREARM. HE RECEIVED FOUR STITCHES.
HE WAS KNEELING INSIDE A SHAKER SCREEN TRYING TO REPLACE A 6" PIPE CONNECTING/SUPPORTING THE TWO SIDES OF THE SCREEN TOGETHER. A RAM PLACED WITH A LONG PIPE WERE BEING USED TO HELP SPREAD TEH SIDES ENOUGH TO SLIDE THE NEW SUPPORT PIPE IN PLACE. BETWEEN THE RAM AND THE PUSH PIPE WAS A PIECE OF STEEL PLATE. IT IS THOUGHT THIS PLATE HIT THE FLOOR OF THE SCREEN, BOUNCED AND HIT HIM.
CLEANING GRIZZLY HITTING IT WITH SLEDGE, ROCK SHATTER LG PC FLEW UP HIT IN MOUTH TEETH CRACKED
I.NAME UNDERNEATH DUMP TRUCK LOOKING UP TO WATCH A PART MOVE AS ANOTHER PRYED THE PART.WHEN PIECE MOVED,FOREIGN MATERIAL FELL ON FOREHEAD,THEN ROLLED INTO EYE.SMALL PIECE OF STEEL WAS REMOVED BY EYE SPECIALIST.
EMPL WAS HOLDING HAMMER TO BEARING CASING WHILE ANOTHER MAN HIT EMPL'S HAMMER TO DRIVE BEARING CASING ON SHAFT. AFTER ONE OF HITS CASING BROKE CAUSING SPLINTER OF METAL TO EMBED INTO EMPLS LEF T ARM. DR REMOVED EMBEDDED METAL SPLINTER & GAVETETANUS SHOT.
EMPL WAS TRYING TO OPEN POUR SPOUT ON PLASTIC 5 GALLON CONTAINER OF OIL. PRYING POUR SPOUT OPEN WITH KNIFE IN LEFT HAND & SECURING CONTAINER WITH RIGHT HAND WHEN BLADE SLIPPED OFF POUR SPOUT & PUNCTURED RIGHT HAND. RIGHT HAND RECEIVED 3/4" PUNCTURE WOUND LOCATED BETWEEN THUMB & INDEX FINGER & RECEIVED SIX STITCHES.
EE WAS CLEANING THE DISCHARGE CHUTE BENEATH SECONDARY CRUSHER BY HITTING THE MATERIAL WITH A PRY BAR. DURING ONE OF HIS JABS, THE PRY BAR CONTINUED PAST AN ANTICIPATED POINT WHICH CAUSED HIS L EFT FINGER TO HIT THE SIDE OF THE DISCHARGE CHUTE. THIS CAUSED THE FINGER NAIL TO BE LOST AND RECEIVED THREE STITCHES IN THE SAME AREA.
HE WAS KNOCKING THE SHANK GUARD OFF OF THE RIPPER SHANK ON A D-9L CAT COZER. ON HIS THIRD STRIKE USING A 5# HAMMER, A PIECE OF METAL BROKE OFF OF THE GUARD AND BECAME EMBEDDED IN HIS LEFT LEG -CALF AREA.
I.NAME LAYING ON BACK TIGHTENING ADJUSTING NUTS ON TAIL PULLEY.WHEN JOB COMPLEWTED,STOOD UP & FELT SOMETHING IN LEFT EYE.WASHING IT DIDNT HELP.WENT TO DR WHO REMOVED SMALL PIECE OF METAL ,RX.
A. NAME WAS USING A PRY BAR TO UNEARTH SOME DE-ENGERGIZED ELECTRIAL CABLE BURIED SEVERAL INCHES BENEATH THE GROUND. AS HE WAS HITTING THE GROUND AND APPROACHING A CONTROL HOUSE STAND MADE OF 3" PIPE, HE HIT THE STAND ON A DOWNWARD THRUST, CATCHING HIS MIDDLE FINGER TIP AND RING FINGER NAIL OFF THE MIDDLE FINGER AND CUT THE TIP OF HIS RING FINGER.
I,NAME WAS TRYI3G TO REMOVE A U-JOINT FROM A DRIVE SHAFT. HE HAD THE DRIVE SHAFT POSITIONED UP RIGHT ON A WORK BENCH AND WAS HAMMERING THE U-JOINT WITH A SMALL 1# SLEDGE HAMMER. AFTER ONE OF H IS STRIKES, A P3ECE OF METAL FLEW OFF OF THE BEARING SURFACE OFTHE U-JOINT ANDBECAME IMBEDDED IN HIS LEFT LEG ON THE SIDE OF HIS KNEE.
I NAME WAS USIN1 PRY BAR ON RT SIDE OF LOADER TO PRY OFF A CARRIER BEARING ON FRONT DRIVE WHILE AT THE SAME TIME ANOTHER MECHANIC ON LEFT SIDE WAS HITTING THE CARRIER BEARING WITH HIS HAMMER O ONE OF THE STRI5ES PRODUCED A FLYING CHIP OF METAL WHICH LODGED IN I NAMES RT FOREARM NEAR HIS WRIST THE CHIP OF METAL MEASUREED APPROX 6 MM LONG X 2 MM IN DIAMETER
I.NAME & 2 OTHER EMN IN THE SHOP WERE ATTEMPTINGTO FREE A DRILL HAMMER FROM THE INSIDE OF ITS CYLINDE. THE CYLINDER WAS BRACED BETWEEN THE FORKLIFTS ARMS THAT RESTED ON THE GROUND. AFTER HEA TING THE CYLINDER ONE MAN HIT THE DRILL HAMMER USING A 10# SLEDGE. I.NAME WAS STEADYING THE CYLINDER WITH ONE FOOT & STANDING IN FRONT OF THE MAN HITTING THE HAMME. AS A BLOW WAS STRUCK A PI
I NAME WAS HELPING BREAK A LARGE ROCK CAUGHT IN THE FEEDER WHEN HE SWUNG THE SLEDGE HAMMER DOWN THE BUTT OF THE HANDLE HIT HIS LEFT SHIN.
NOELIO WAS WELDING BRACKETS ON SAND SCREW DIRECTLY ABOVE HIM ON PLATFORM WERE MARK MOTHERAL AND RUBEN MONTALVO WHO WERE TURNING A SAND CLASSIFIER USING A PRY BAR RUBEN WAS PRYING WITH THE BA R AS MARK WATCHED FOR ALIGNMENT BAR SLIPPED AND CAME DOWN HITTING NOELIO BELOW THE BACK OF NECK BAR DID NOT FALL FREELY AS RUBEN HELD ON TO IT REDUCING FORCE OF IMPACT HE DID NOT SEE PHYSICA