Buscar en el registro

Operator was cutting a conveyor belt section. EE was almost all the way through the belt when the knife slipped through and hit EE's upper leg. About 8" up from the knee.

EE was adjusting a tail pulley with a breaker bar. EE was using a wrench to loosen the pulley when the breaker bar loosened suddenly, causing EE's body to jerk and fall to ground landing on right knee. Injury resulted in an indicated meniscus and ACL tear.

Employee was using a bar to poke chute when a rock fell onto the bar. Employee held on to bar as it pulled him, causing a muscle strain in his left shoulder

Cutting rubber tabs off of a screen panel. Knife slipped and cut left index finger. 3 stitches were required. Returned to work the same day.

Using pry bar and porter power to repair water drain for belt press. Pry bar slipped and jarred his left arm. Neck Sprain.

While using a utility knife, the knife slipped off and he cut his leg. Stitches.

Employee was using a hoe to pull rock off of shot. Another rock rolled off screen and struck ee in month. We recently received aother and dx from dentist.

Installing wedges that hold ball liner in crusher. Was holding wedge in one hand and using hammer in other hand. Struck tip of right thumb with hammer.

Putting platform on drill rig, when wrench he was using slipped off. Left arm slipped and he felt pain in left shoulder. Shoulder strain.

EE WAS UNWIRING MOTOR OF BLACKTOP PLANT. MOTOR WAS TAPED WITH ELECTRICAL TAPE- EE WAS CUTTING TAPE OFF WITH RAZOR KNIFE. KNIFE SLIPPED AND CUT THROUGH GLASS, LACERATING RIGHT INDEX FINGER.

EE WAS WORKING ON CRUSHER LOOSTENING MOTOR BASE BOLTS. LEFT HAND SMALL FINGER WAS PINCHED BETWEEN WRENCH & MOTOR BASE.

PULLING UTILITY KNIFE ACROSS STIRTING A SECONDARY CRUSHER. KNIFE SLIPPED & LACERATED R FOREARM.

HAMMERING WEDGE THAT HOLDS 4' CRUSHER TIGHT, MISSED WEDGE AND STRUCK LEFT SMALL FINGER.

TIGHTENING BOLTS IN CRUSHER - STRAINED BY PULLING ON RATCHET. SAW OWN CHIROPRACTOR - FEW SESSIONS.

OPENING UP CHAIN LINK USING HAMMER. STRUCK LT. THUMB WITH HAMMER.

DRIVING TRACK CHAIN PIN IN PLACE WITH 12 LB. SLEDGEHAMMER. A CHIP FROM TRACK PIN LACERATED INSIDE OF LT. THIGH.

CUTTING A FLOOR MAT FOR THE TRUCK, USING UTILITY KNIFE. KNIFE SLIPPED AND LACERATED RIGHT UPPER THIGH.

WHILE CUTTING USED CONVEYOR BELT, SLIPPED WITH UTILITY KNIFE AND LACERATED LEFT HAND AT BASE OFTHUMB.

EMPLOYEE WAS TIGHTNING A 5" DIAMETER BOLT ON TRAYLOR CRUSHER, USING A 3-0 CAST WRENCH AND 1.5 TON COME-A-LONG. THE WRENCH SNAPPED AT THE NECK. THE EMPLOYEE FELL BACKWARDS; STRIKING HIS HEAD ON ANGLE IRON OF HANDRAIL.

EE WAS CUTTING JOINT IN RM BELT WHEN HE SLIPPED WITH A RAZOR KNIFE CUT R THUMB NO GLOVES.

CHANGING DECK PLATES IN PRIMARY CRUSHER. HAMMERING ON PLATE TO LOOSEN. AFTER 3RD HIT WITH HAMMER, PLATE (200 LBS) BLEW OUT OF ITS SEAT AND HIT EE IN THE LFT LEG.

WAS USING A 4.0 PRYBAR TO UMPLUG A CHUTE. BAR SLIPPED & HIT SAFETY GLASSES & LEFT EYE.

WAS JACKING FLYWHEEL WHEN A PIECE OF ANGLE IRON BEHIND HIM FELL STRICKING HIM IN HIS BACK (300 LBS) 4X4 ANGLE WITH 3/8 PLATE WELDING TO FLYWHEELCAUSED ANGLE TO SHIFT & FALL. METAL FATIGUE AND DIRT BUILD UP DIDN'T SEE BROKEN BITT (HAMMERING ON ANGLE

WAS TRYING TO TIGHTEN SCREW ON OIL STICK OR WELDER USING A JACK KNIFE FOR A SCREW DRIVER AND IT FOLDED ON RIGHT INDEX FINGER.

INSTALLING ROPS ON LOADER, BAR SLIPPED, R INDEX FINGER GOT CAUGHT BETWEEN BAR & CAB OF MAHCINE.

INSTALLING A PTO MACK PUMP INTO MOUNT WHILE TIGHTENING NUTS & BOLTS, WRENCH SLIPPED & STRUCK LOWER LIP.

EE ALLEDGES HE WAS PERFORMING EXCESSIVE SHOVELING IN AN AWKWARD POSTION COMBINED WITH BENDING OVER TO EMPTY LARGE CRUSHER OF SEVERAL STONES.

EE STATES THAT WHILE ATTEMPTING TO FIX A CONVEYOR WAS USING A PRY BAR UNDER A ROLLER. PRY BAR SLIPPED CAUSING EE TO FALL AGAINST PRY BAR.

EE STATES PRYING ROCK OUT FROM CHUTE OF PRIMARY CRUSHER--EXPERINECED PAIN LEFT LOWER BACK.

EE STATES DISMOUNTING ROLL CRUSHER TIRE USING A PRY BAR. BAR SLIPPED STRIKING EE IN MOUTH RESULTING IN A CHIPPED TOOTH.

EMPLOYEE WAS CHANGING THE BUSHING ON A WALKING BEAM OF A DUMP TRUCK. HE WAS CUTTING AWAY THE RUBBER ON THE OUTSIDE OF THE BUSHING WHEN THE KNIFE SLIPPED AND CUT THE LEFT INDEX FINGER.

EMP WAS HITTING A PIN WITH HAMMER. PIECE OF METAL FLEW OFF HITTING HIM IN THE CHEEK.

EMPLOYEE WAS REPAIRING CRACKED GRIZZLY BA AT RIP-RAP PLANT. THE BAR SLIPPED OUT OF THE CHAIN AND HIT EMPLOYEE ON THE LEFT ARM AND SHOULDER. EMPLOYEE WAS TAKEN T O ALBNY MED FOR EVALUATION AN D RELEASED. NO TIME LOST ACCIDENT.

EMPLOYEE WAS REMOVING A LODGED ROCK FROM BETWEEN TWO TANDEM TIRES HE SWUNG A HAMMER AT THE ROCK THE HEAD OF THE HAMMER FLEW OFF & STRUCK THE EMPLOYEE IN THE MOUTH THE EMPLOYEE REQUIRED STITCHE S TO CLOSE HIS UPPER LIP HIS FRONT RT TOOTH WAS CHIPPED BY THE HAMMER HEAD

EMPLOYEE WAS TIGHTENING BOLTS ON A CRUSHER WHEN HIS ELBOW STRUCK THE FRAME OF THE CRUSHER.

EMPLOEYE SHOVELING AT TAIL PULLEY OF SHORT CONVEYOR HIT THUMB (LEFT) ON GUARD AS HE PLUNGED SHOVEL INTO MATERIAL (STONE) BUILT UP UNDER TAIL PULLEY.

INJURED WAS TURNING A CRUSHER BOLT WITH A WRENCH. WRENCH SLIPPED OFF HEAD OF BOLT CAUSING EMPLOYEE TO FALL, THEREBY TWISTING HIS KNEE.

PAINTING A SEALER COATING ONTO ROOF OF MILL CONTROL ROOM. WOKE UP NEXT MORNING TO A PAINFUL BACK.

PUNCHING HOLE IN RUBBER BELTING WITH A HAMMER & HOLE PUNCH UPON IMPACT PIECE OF STEEL CAME OFF OF PUNCH & ENTERED LEFT THUMB NEAR JOINT

WORKING ON CRANE CLUTCH. USING WRENCH, WHICH SLIPPED AND SMASHED RIGHT HAND.

JACKING TWO PIECES OF METAL APART. JACK SLIPPED & HIT EMPL IN HEAD.

PULLING TOGETHER AND CLIPPING BELT ON 5 1/2 IN MILL BELT TIGHTENER ARM LET LOOSE AND CAUGHT FINGER