Buscar en el registro

Employee was performing regular maint. on boiler tubes. Employee alleges that the rebar he was using became lodged between two tubes. When he pulled rebar out he felt a pain in left shoulder. Employee started physical therapy as of 11/29/2007.

Employee used his own pocket knife to cut a plastic clip off a quard so he could do some repair work. Knife slipped and cut left hand.

Employee was rolling over a hammer on the secondary hammer mill. He alleges that while he was bent over putting a bar under the hammer he felt something give.

Employee was working at # 3 Kiln Pier #1 prying on bearing cap to pull off and felt pain between shoulders.

Employee was pulling on bar in screw box to line up holes to put bolts in screw.

Employee using rebar to remove loose buildup of hot dirt in between boiler tubes. Employees claims he felt a sharp pain and elbow started swelling.

HE WAS HAMMERING A METAL PLATE INSIDE A BALL MILL AND A PIECE OF PLATE CHIPPED OFF AND STUCK IN HIS RIGHT LEG.

EMPLOYEE WAS SCOOPING CLINKER IN THE WALKWAY ONTO THE BELT. DUST FROM SCOOPING LINGERS IN THE AIR. EMPLOYEE FELT DUST GET IN HIS EYES.

EMPLOYEE WAS PUTTING A FINAL PIECE OF EQUIPMENT AND TIGHTENING BOTTOM BOLTS WHEN WRENCH SLIPPED OFF AND HE FELL BACK ONTO A WHEEL BARREL ABOUT 5 FT BEHIND HIM. HE BRUISED BACK AND RIGHT KIDNEY AREA.

EMPLOYEE WAS HAMMERING ON STEEL PLATE AND FRAGMENT CHIPPED OFF STRIKING HIM ON THE RIGHT CHEEK.

EMPLOYEE WAS CLEANING OUT HOPPER PIPE WITH A HAMMER. THE HAMMER SLIPPED AND HIT HIS FINGER.

EE WAS TRYING TO PIVOT THE CRADLE WITH A SET OF COMEALONGS THE BOLT THAT HE WAS USING TO PULL WITH CAME LOOSE & STRUCK HIM IN THE BACK

EE AND CO WORKERS WERE LOOSENING BOLTS ON LINE SHAFT BEARING AT NORTH PRIMARY MILL. INJURED WAS HOLDING WRENCH WHILE CO WORKER WAS HITTING WRENCH WITH SLEDGE HAMMER. WHILE IN BACK SWING, SLEDG E HAMMER HIT MILL CAUSING SLEDGE TO MIS-HIT ON WRENCH AND HIT INJURED S LEFT HAND.

EMPLOYEE WAS OPENING #8 BAY DOOR AT BAG HOUSE USING A CHEATER BAR. THE DOOR HAS A VACUUM SEAL TO BREAK. THIS IS DONE AT LEAST TWICE A WEEK. TWO DAYS LATER EMPLOYEE'S LEFT WRIST BECAME SWOLLEN. WENT TO COMPANY DR. 4-9-98. X-RAYS TAKEN - NO BONE BROKEN. ARTHRITIS DIAGNOSIS. EMPLOYEE PLACED ON RESTRICTED DUTY ON WEEK MAKING THIS REPORTABLE.

EE WAS PREPARING TO REMOVE BROKEN COMPRESSOR AT FINISH END TO INSTALL A NEW ONE. HE WAS LOOSENING UP NUTS & BOLTS & STRAINED HIS LOWER BACK.

EE WAS TRYING TO MOVE DRIVE MOTOR TO ADJUST BELT TENSION ON NO. 1 CLINKER COOLER HAMMERMILL. HE WAS USING A HANDBAR TOMOVE THE MOTOR WHEN HE SPRAINED HIS RIGHT SHOULDER.

EMPLOYEE WAS CUTTING TWO TIE ROPES FROM WIRES USING A KNIFE. FIRST WAS HARD TO CUT AND OFFERED SOME RESISTANCE. SECOND TIE CUT AWAY EASILY, SOME PRESSURE HAD BEEN APPLIED, WHICH ALLOWED KNIFE TO GO THE OTHER 6" AND CUT INDEX FINGER LEFT HAND.

EMP AND COWORKER WERE ADJUSTING #4 KINL ROLLS FOR BRASS INSERT WEAR WITH INJURED HOLDING 42LB WRENCH AND COWORKER STRIKING WRENCH WITH 16LB SLEDGE HAMMER. EMP THOUGHT COWORKER WAS FINISHED WIT H HAMMER AND PLACED LEFT HAND AT IMPACT POINT ONWRENCH. COWORKER SAW INJURED MOVE HAND BUT COULDNOT STOP HAMMER SWING IN TIME TO KEEP FROM SMASHING FINGER.

EMPLOYEE AND CO-WORKER WERE CHANGING OUT RETURN ROLL ON 1.6 BELT ABOVE COUNTERWEIGHT AT RAW MILL. THEY WERE LIFTING COUNTERWEIGHT WITH COME-A-LONGS WHEN COME-A-LONGS SLIPPED, JERKING EMPLOYEE INJURING HIS RIGHT SHOULDER. WEATHER WAS VERY, VERY COLD.

EE AND CO-WORKERS WERE TAKING TOP SPROCKET OFF BIG DUST ELEVATOR. EE WAS LOOSENING BOLTS WITH WRENCH. WHILE PULLING ON WRENCH HE TWISTED HIS BACK. WENT TO CO. DR. AND CHIROPRACTOR RECEIVING OM T WHICH MAKES THIS REPORTABLE.

EE WAS CLEANING WOUTH BACKHOUSING FLUES IN THE "T" JUNCTION HOPPER AT BACKHOUSING. WHEN CHUNKS DO NOT BREAK UP, EES USE A LONG PIPE HOE AND REMOVE CHUNKS THROUGH A SMALL DOOR. EE SUFFERED A MU SCLE STRAIN ON 7-15 BUT DID NOT SUBMIT AN ACCIDENT REPORT UNTIL 7-26. SAID HE THOUGHT IT WOULD GET BETTER. REQUESTED TO SEE A DR. 7-29. COMMENCED LOSING TIME 7-30.

HOPPER WAS PLUGGED UNDER #4 KILN TAIL RING. EMPLOYEE RAN A ROD UP IN THE HOPPER TO UNPLUG IT AND SOME HOT DIRT FELL OUT THE SEAL ONTO HIS EAR AND FACE.

PROD. SUPERVISOR WAS TAKING KILN GUN OUT OF #3 KILN WHEN HE INJURED RT SHOULDER. A PULLEY IS USED TO UNLOAD AND LOAD GUNS OFF A CART INTO KILN AND REVERSE PROCEDURE WHEN THROUGH SHOOTING RINGS . EE DID NOT REQUEST TO SEE DR UNTIL 6-19 WITH APPOINTMENT WITH CO DR ON 6-21. DR INJECTED CORTISONE INTO SHOULDER AND DIAGNOSED TENDONITIS. EE HAS REQUESTED SECOND OPINION.

PRODUCTION SUPERVISOR WAS SHOOTING BUILD-UP ON NOSE RING IN #1 KILN AND HAD HOT COATING FLY BACK HITTING RIGHT SIDE OF NECK. WAS WEARING FACE SHIELD, DUST MASK, EAR MUFFS AND A RAG ON HEAD WH ICH OCVERED BOTH EARS AND BACK OF NECK.

WORKING ON PUFF, TURNING BOLTS WITH WRENCH TO TIGHTEN, WHEN HE FELT A STEAIN IN LOWER BACK.

EE WAS TRYING TO CLOSE TAILGATE ON DUMP TRUCK. HE WAS CLEANING THE DRIED MUD OFF THE AIR LOCK ARMS AND CLEANING TAIL GATE GROVE OUT USING A HAMMER. IMPACT OF HAMMER ON DRIED MUD INJURED RIGHT SHOULDER.

EMPLOYEE WAS REPLACING BOLTS ON #1131 FRONT END LOADER.HE HAD DRIVEN THE PIN OUT AND LINED UP THE BOLT HOLES.WAS IN PROCESS OF DRIVING PIN BACK IN WHEN HE FELT SOMETHING GIVE IN HIS LEFT SHOUL DER CAUSING INTENSE PAIN.HE STOPPED AND SHOOK ITOFF.PAIN INCREASED SO HE FINISHED JOB.LATER PAIN RETURNED.CO DR OUT OF TOWN.APPT WITH DR R OSBORN REFERRED HIM TO SOUTHEAST KS ORTHOPEDICS,CHAN

EMPLOYEE WAS RODDING OUT THE HOPPER WHEN DUST SLID DOWN, BLOWING OUT. EMP WAS BURNT ON BOTH ARMSWENT TO CO DR 12-15 WHO RELEASED HIM FOR WORKINGAWAY FROM HEAT. EMP WENT TO PHYSICIANS ASST - CE RT AT CHERRYVALE CLINIPUT HIM OFF WORK 12-16-95.

EMP WAS REMOVING BOLT FROM COVER LID ON QUARRY HAMMERMILL. WHEN HE TURNED, HE FELT PAIN IN HIS BACK. EMP WENT TO CO DR WHO PERFORMED OMT, MAKINGTHIS REPORTABLE.

EE HAD DUST PIPE, 24" X 20' LONG, HANGING AT APPROX. 60 DEGREE ANGLE, SUSPENDED ON BOTH ENDS BY CHAIN FALLS. EE WAS STANDING ON ENCLOSED SCAFFOLD ABOUT 10' OFF FLOOR AT LOWER END OF PIPE. HE L EANED INTO PIPE TO REPOSITION THE LOWER CHAIN. CHAIN SLIPPED ALL THE WAY UP PIPE, TAKING HIM WITH IT, PULLING HIM DOWN ABOUT 10' AND OVER ABOUT 14' FROM THE SCAFFOLD.

EMPLOYEE WAS HELPING CO-WORKERS FREE UP JACKHAMMER BIT THAT WAS STUCK IN CASTABLE AT NORTH BOILER. WHYEN PRYING ON BIT SOME CASTABLE BROKE LOOSE AND HIT EMPLOYEE IN LEFT EYE. HE WAS WEARING PRESCRIPTION SAFETY GLASSES.

EE AND COWORKER WERE PUTTING SEAL INTO PLACE ON #3 KILN. EE WAS WORKING OFF A LADDER AND STRAINED HIS BACK PRYING SEAL INTO PLACE. EE HAS A HISTORY OF BACK STRAINS AND SPRAINS.

EE WAS CLEANING A DUST SPILL AT NEW DUST SCREW AT ROCK SILOS. HE WAS PREPARING TO MOVE DUST AWAY FROM SCREW BOX. HE HAD PLACED A HOE LEANING AGAINST A STEEL COLUMN. THE HOE HAD FALLEN TO FLOOR . AS HE MOVED, HE STEPPED ON BLADE OF HOE, CAUSING HANDLE TO STRIKED HIM ON UPPER LIP.

EE WAS MAKING A CLINKER PULL TO FILL CLINKER TANKS. CLINKER HOPPER BRIDGED OVER MAKING IT NECESSARY TO ROD HOPPER TO GET CLINKER TO COME DOWN HOPPER. WHILE RODDING INSIDE OF HOPPER WITH A BAR IN HOLE ON SIDE OF HOPPER, WORKING UP AND DOWN MOTION, HE HIT GRATING INSIDE OF HOPPER AND FELT A SHARP PAIN IN HIS RIGHT SHOULDER.

EE WAS ROLLING FLYWHEEL BACK ON BEDESHI TO CLEAN IT. HE WAS PRYING ON FLYWHEEL WITH A SOLID STEEL BAR APPROX. 4' LONG TO ROLL FLYWHEEL BACK. AS HE WAS PRYING WHEEL MOVED AND BAR CAME DOWN PINN ING HIS FINGER BETWEEN BAR AND A CONCRETE BASE. SPLIT END OF HIS LITTLE FINGER LEFT HAND.

EMPLOYEE AND CO-WORKERS WERE USING 6 TON PULLERS TO GET #2 KILN HOOD AWAY FROM KILN. INJURED WAS PULLING ON PULLERS WHEN HE NOTICED NUMBNESS IN HIS LEFT ARM.

EMPLOYEE WAS INSIDE SILO #21 HOEING TYPE S MASONRY INTO AN AIRSLIDE FOR PACKING. AS HE WAS HOEING CEMENT INTO AIRSLIDE LOOSE CEMENT FEW ONTO HIS FACE, ENTERING HIS EYES. HE WAS WEARING SAFETY GLASSES.

54736YEE WAS SHOVELING SOLIDS MATERIAL WHEN THE RIGHT ELBOW POPPED. THEN WHILE EMPLOYEE WAS HAMMERING ON A SOLIDS TOTE THE EMPLOYEE HIT HIS RIGHT ELBOW.

EE WAS RODDING OUT COAL TANK HOPPER WITH A 7FT STEEL BAR WHEN HE FELT PAIN IN HIS LOWER BACK.

EMPLOYEE WAS HOEING RAPID SET CEMENT INTO SCREW BOX INSIDE SILO #8 TO CLEAN OUT SILO AND GOT CEMENT DUST IN HIS EYES.

AFTER GETTING A GYPSUM HORN ALARM, EMPLOYEE PROCEEDED TO FEEDER WEIGHT FLOOR WHERE HE PUT A BAR UNDER ALARM ARM AND GYPSUM FEEDER. AFTER RSTARTING FEEDERS, HE CLIMBED STAIRS TO TO PFLOOR AND STARTED BLOWING SYPSUM DOWN. HE BEGAN HAVING PAIN IN HIS LOWER BACK AND LEGS.

ADJUSTING RUBBER SCRAPER ON HEAD ROLL REACHING ACROSS USING HANDLE OF WRENCH HEARD SOMETHING POP

EMPLOYEE WAS USING A CEMENT HOE TRYING TO EMPTY BIN #5 OF UNFLOWING CEMENT INTO A SCREW WITHDRAWAL SYSTEM. EMPLOYEE WAS STANDING IN CEMENT FOR QUITE SOME TIME. EITHER HAD CEMENT BURN OR REACTI ON TO CEMENT.

RODDING CHUNKS FROM BELOW HOT FLUE BEHIND 2 KILN CHUNKS BROKE LOOSE INJ BURNED HOT DUST CHUNKS

EMPLOYEE WAS REACHING DOWN AND IN WITH BODY STRETCHED OVER OUTSIDE RAILING OF VIBRATING SCREEN IN FINISH MILLS TO REMOVE NUT FROM HOLD-DOWN BOLT. BOLT WAS EXTREMELY HARD RUNNING AND REQUIRED H ARD PULLING ON WRENCH. INJURED FELT ONLY SLIGHT BURNING AND DIDN'T FIND RUPTURE UNTIL TAKING SHOWER AT HOME APPROX. 5 PM 4-19-91/

INJURED WAS REPAIRING MAIN LINE SWITCH. HE WAS LIFTING RERAILER INTO LOADER BUCKET WITH USE OF CHAIN TO DRAG IN LOADER BUCKET. HE FELT A SLIGHT PAIN IN LOWER BACK.

THERE WAS BUILDUP UNDERNEATH BEDESCHI ROLLS WITH CLEANOUT DOOR THAT YOU OPEN TO REACH UNDERNEATH ROOLS TO CLEAN REPIRED TO TAKE BAR & LAY ON BACK & PICK BUILDUP OFF OF ROLLS. AFTER NORTH SIDE WAS CLANED HAD TO REACH INSIDE DOOR FURTHR TO REACH BUILDUP ON SOUTH SIDE. BY LAYING ON BACK & HAVING TO REACH UP EMPL OVERSTRAINED LEFT SHOULDER.

EMPLOYEE WAS TURNING SHAFT ON ELEVATOR CONTROL ROOM PASSENGER ELEVATOR MOTOR USING CHANNEL LOCK PLIERS. HE EXPERIENCED A STRAIN-RIGHT TESTICAL AND TUBE BETWEEN TESTICAL AND PROSTATE GLAND.

SHOVELING DUST FROM ROCK SILO SCREW, DUST PUFFED BACK, STRIKING FACE

INJURED WAY TRYING TO REMOVE GUDGEON FROM SCREW CONVEYOR IN FINISH DEPT WITH PINCH BAR. SCREW SLIPPED OFF OF BAR CATCHING FINGER IN PINCH POINT.