Buscar en el registro

SHOVELING DEBRIS IN & AROUND CHUTE & SMASHED FINGER

EE was removing a thermocouple from the tower using a pipe wrench. The pipe wrench slipped off the thermocouple and pinched left pinky between the pipe wrench and the handrail.

While striking a bar with a hammer a small piece of the bar splintered off of it going into ee left forearm

Employee was removing a come along from a forklift and set of cribbing. Forklift shifted and employee's right middle finger got lacerated.

EE was lowering a blastline into a column when his left 4th and 5th fingers became caught between the pulley and the rope. This resulted in lacerations to these fingers. The employee's wounds were immediately treated on site and he was then taken to a clinic to be examined. He was diagnosed with a nail avulsion, given 3 stitches, and a tetanus shot. He was then released to work.

The EE was putting the pin gate in on 41WF06 with a hammer. He was in an improper position for the task and hurt his back.

EE was swinging a hammer at a return roller on a belt conveyor and missed it. This caused his hand to in between the roller and conveyor belt.

EE was prying on a door and the pry bar slipped. When the bar slipped it pinched his left index finger in between the pry bar and the kiln hood causing a cut to the tip of his finger.

EE was driving a pin into the drive track of the drill. After striking the pin with a hammer a small sliver of metal from the pin entered EE's left hand.

Employee was cutting skirt rubber with a utility knife. As he was cutting the rubber, he cut through the rubber faster than he anticipated and the knife slipped and cut his lower right thigh just above the knee.

Employee was pulling on a coupling with a porta-power and was hitting the coupling with a sledge hammer to jar it loose when a piece of the coupling broke loose and struck the employee in the face. The employee suffered some contusions on the left side of the face.

Employee was assisting with the retorque of a 1 1/2" Cap screw and re-agrivated and old hernial injury.

Employee strained the lower back using a 60 lb bar to strike the door to #3 ball mill to break the seal so the door could be opened.

EE was attempting to loosen a bolt for the drive mechanism on 34BC08 and strained his right shoulder while pulling on a wrench.

EE reports that in February or March of 2006, he strained his neck and L shoulder while dislodging oversized material at the Tower A grizzley. EE reported the incident to management on July 27, 2006. the incident is being investigated for compensability.

EE WAS SPLICING A CONVEYOR BELT, CUTTING THE BELT WITH A RAZOR KNIFE. HE WAS CUTTING TOWARD HIMSELF. THE KNIFE SLIPPED OUT OF THE BELT & WAS PULLED ACROSS RIGHT KNEE CAUSING A LACERATION ABOVE RIGHT KNEE CAP.

OPERATING COMEALONG HEARD POP IN LEFT SHOULDER.

HITCHING TRAILER, JACK COLLAPSED, TRAILER ROLLED AND HIT EE IN ELBOW (RT).

A 20 LB SLEDGE HAMMER WAS BEING USED TO HIT A BEATER BAR TO REMOVE A LARGE NUT. THE SLEDGE MISSED THE BEATER CAUSING HIM TO FALL BACKWARDS AND SLEDGE DROPPED ON HIS LITTLE FINGER RESULTING INA FRACTURED BONE.

SMASHED INDEX FINGER WHILE PRYING.

MAKING A SILO CHANGE, RIGHT HAND SLIPPED BAR FELL SMASHING RIGHT MIDDLE FINGER.

WHILE PULLING 4" PLASTIC HOSE TO CATWALK APPROX. 10' OFF GROUND HAD ROPE ATTACHED TO HOSE TO HELP PULL UP WAS BENT OVER AND FELT FELT PULLING IN LOWER BACK MUSCLE.

EMPLOYEE WAS PUTTING ULTRAVAC WITH 2 YD LOADER. DID NOT MAKE WIDE ENOUGH TURN CAUSING ULTRAVAC TONGUE TO JAM UNDER RIGHT TIRE. EMPLOYEE REMOVEDBOLT TO RELEASE TONGUE. TONGUE WAS UNDER A LOT OF TENSION AND SNAPPED UP AND HIT EMPLOYEE 'S RIGHT THIGH AND LEFT SHIN.

EE WAS ATTEMPTING TO LOOSEN THERMOCOUPLE WITH LARGE CRESCENT WRENCH. EE PUSHED TOO HARD AND STRAINED HIS RIGHT THUMB, BECAUSE THERMOCOUPLE HAD STUCK.

EE WAS INSTALLING TRANSMISSION TO ENGINE ON GARAGE SHOP FLOOR. ENGINE AND TRANSMISSION SLIPPED OFF JACK. HE GRABBED TRANSMISSION TO KEEP IT FROM FALLING.

EMPLOYEE WAS BARRING DOWN ON BRICK USING A LONG BAR (IN KILN) WHILE BARRING DOWN EMPLOYEE FELT SHARP PAINS IN HIS HANDS ARMS & BACK

54736YEE WAS REMOVING CHUNKS FROM FEEDER.BAR SLIPPED AND HIT SIDE OF FEEDER.

EMPLOYEE WAS REMOVING TURN BUCKLE FROM BURNER PIPE. PIPE WAS ONLY RIGGED WITH 1 COM-A-LONG FOR ONE DIRECTION. PIPE MOVED PINNING HAND BETWEEN FRAMEWORK AND TURN BUCKLE CRUSHER LEFT HAND.

EMPLOYEE WAS LAYING BRICK IN THE KILN.WHEN HE HIT THE BRICKS WITH A MALLET TO MOVE THEM,MORTAR SPLASHED AND WENT INTO THE RIGHT EYE.

EE WAS TIGHTENING FUEL LINES ON BLUE DUST TRUCK 9097, WHEN HAND SLIPPED OFF THE WRNECH AND HAND WENT INTO FAN BLADE.

EMPLOYEE WAS CUTTING COVERS WITH TIN SNIPS OUT OF TIN. EMPLOYEE REPORTED NUMBNESS OF RIGHT THUMB TO SUPERVISOR ON 7-26-91.

EMPLOYEE WAS ATTEMPTING TO REMOVE A KEYSTOCK WITH A HAMMER MATERIAL GAVE AWAY & FLEW UP STRIKING HIM IN THE CHIN