Buscar en el registro

EE reported feeling a popping sensation in left wrist while using a pipe wrench. EE reported some tenderness in outer part of left wrist. No swelling or deformity noted.

EE reports via phone that while working to replace the dump cables on the #3 dragline, when beating them out of their sockets and missed the swing. EE reports that this missed swing caused the movement to snatch the EE left's shoulder. EE reports left shoulder pain with movement.

EE reports pulling on a wrench and experiencing a pop in the right-side chest muscle. EE states pain with movement of arm. On physical exam there is a tender lump in the muscle.

Employee (EE) reported to the Clinic on 03/12/2024 and stated that while attempting to loosen a bolt with a ratchet, while pulling handle towards their body, they felt lower back pain. EE was referred to Company Care. Restrictions were given that cannot be accommodated. EE is off work until further notice.

On 12/29/23 Employee was using a pry bar to open a door on a pit pump. The pry bar slipped and struck the EE in the face causing a partial thickness facial laceration. EE was treated at the onsite clinic and returned to work, with no restrictions or lost time to report.

On 09/27/2023 Employee-EE stated they pinched their right hand between a wrench and a cylinder and reported swelling and pain in the area. EE was referred to Co. Care for eval. and treatment. EE has returned to work with restrictions until further notice.

EE was using a pry bar to turn the pump assembly for alignment when the bar slipped and struck the employee on the nose. The impact caused a laceration to the left side of the nose. EE went to a clinic for evaluation and treatment.

EE was using a pry bar to take swing brake off swing motor. When EE applied pressure to bar EE experienced pain under right pectoral muscle, initially filed as report only. Employee contacted Clinic 12/15/22 requesting evaluation & treatment due to on-going pain stating unable to breathe normally or sleep normally due to pain. EE went to LCMC-ED for treatment. No restrictions.

EE was installing a packing in WBC matrix pump. EE was turning shaft to tighten impeller against the packing sleeve, using a 48" pipe wrench to turn impeller shaft. Shaft became difficult to turn but was not fully seated against packing. When EE pulled with force, EE felt pain in right elbow. EE was sent to company care and will be out of work, follow up appointment scheduled.

Employees were tying in a pipe on #4 Dragline area attempting to get bolts in pipe. Co-worker was using 1 5/8 wrench to tap the bolt in when injured employee placed a hand in the way causing wrench to contact left hand. EE transferred to Medical, appt scheduled with Ortho institute on 8/9/22. Possible crush injury to left hand.

Employee was using a pry bar to remove a stump that was stuck in a pump when EE's finger became pinched between pry bar and a solid metal surface. Right ring finger has small bruise under the fingernail with slight abnormal bend to fingertip. EE was sent off-site for evaluation, x-ray was negative. Diagnosis was crush injury to tip of right ring finger, placed on modified duty.

Employee was tasked with replacing belts on a pump. As EE was turning the pump sheave with a pipe wrench, the momentum of sheave caused the employee's finger to get pinched between the pipe wrench handle & a belt guard mounting bracket. EE was seen by onsite EMT & sent to LCMC where x-rays showed a fracture in tip of finger. EE will have surgery on 6/23/21.

EE was clearing debris from hydraulic ditch with potato rake. EE was pulling up on rake, it got hung up and EE felt shoulder pop, felt a sharp pain and cannot move it past a certain point. EE went to an emergency room, referred to an Ortho clinic on 3/18. EE has not returned to work.

HEO was assisting a Ut.Op remove stump from suction of #4 pit pump. A 10' rod used to force debris from end of vertical section of pipe. They placed rod in suction inspection door & on stump, rod slipped off stump & dropped. Finger was pinched between flange of inspection door & handle of rod. HEO was taken to clinic then to hospital, staff cleaned wound & prescribed antibiotics.

Employee was attempting to trim a plastic tab on hard hat halo attachment using a pocket knife when the knife slipped and caused a laceration to left thumb below the first joint.

Employee was standing near 10-wheeler boom truck about 12-15" from hoist cables at #2 D/L. Two other employees were using a 8 lb. sledge hammer and RR maul to drive wedge out of hoist socket. A piece of metal sheared from the maul and traveled approx. 12-15" striking employee in back of right calf.

Employee hit his left thumb with small sledge hit as he was driving a bull pin in a plate dog installing steel panels inside a tank. suffered a laceration and fractured left thumb tip. laceration required sutures to close wound

Employee was closing bottom door on railcar using bar, while pushing on bar, it slipped out of the hole on door closing mechanism. Employee felt sharp pain in right side of lower back.

Employee stated that while he was mopping the floor inside the house at #3 dragline, he felt discomfort in his lower back.

Employee was replacing a damaged hyraulic line on a D8R tractor. Employee had to lie on his stomach to access the connection of the line. He then had to reach as far as possible to get his wrench on the bolt heads. As he went to loosen the bolts, his wrench slipped off the bolt causing a sudden jerk, straining his neck. Employee recently began physical therapy for treatment.

EE HAD THE TASK OF REMOVING PARTS FROM A 3406 CAT D8N ENGINE. IN REMOVING PART FROM THE CYLINDER HEAD, EE HAD A PROBLEM WITH THE BOLTS SECURING THE TURBO MOUNT TO EXHAUST MANIFOLD. THE NUTS WE RE NOT HEAT RESISTANT AND HAD ROUNDED OFF. EE MADE THE DECISION TO USE A CHISEL. EE HAD ALMOST FINISHED THE CUTTING, WHEN HE MISSED CAUSING THE CHISEL TO HIT HIS L THUMB AGAINST MANIFOLD, CUT