Buscar en el registro

Employee was using a sledge hammer to try to free the wear plate on a D10 dozer blade. A metal fragment broke off the plate and struck the employee in the leg.

Employee suffered a neck strain when a sledge hammer head came off of a hammer, striking them on the hardhat. The hammer was being held by another worker as the injured miner was assisting loosening a bolt.

Prying cobble on inside slide with a section of pipe

Employee was using a bar to clear a sand hopper. Five days later, employee said elbow was hurting. Employee reported the injury on 12/20/2016.

Employee was installing rubber screens with a slide hammer in the middle deck of a screen. When he was hitting one screen in the bottom of the hammer slipped off the panel and causing the whole slide hammer to fall suddenly and smash his finger between the handle of the hammer and the bucker bar rail on the top deck.

Employee was on p-8 stacker to perform a belt splice. While securing the tail of the belt to the splicing board the employee struck his right thumb with a hammer.

While removing the use liner from the head of an Omni Cone Crusher, the employee was lifting with a crane and hitting the liner with a 3 lb hammer to break it loose. The hammer struck the employee's right middle finger.

Employee was prying worn rubber that had been siliconed to a chute with a crowbar. When the rubber came loose the crowbar slipped from the employee's grasp causing the bar to drop to the ground which caused the employee to drop to his knees striking his left knee on the center hold down bolts of a screen.

While using a 12 lbs hammer to clear rocks form a vibrating grizzly screen, the employee struck the right index finger with the hammer.

The employee began to notice pain in his low back after using a 16 lb hammer to install a head bolt of a crusher. As the pain began to intensify the employee requested medical intervention for the low back pain.

The employee was clearing out a head-box with a long bar when his left hand became caught between the bar and a piece of angle stock inside the box.

While cutting flag cable for a water conveyor extension with a short handled four pound sledge hammer, the hammer missed the correct contact. It instead struck the employee on the webbing of the left hand between the forefinger and thumb.

The employee was using a utility knife to open a package of padlocks for his work locker. He bended his knee and used the upper thigh as a wooden block for cutting purposes. The utility knife slipped and sliced open the left leg, upper thigh.

The employee was hammering a keeper pin in a new ripper shank guard on D11 dozer. He steadyed the guard with his legs while hammering, striking his left knee with the hammer.

The employee was removing the outside bolts of a tailpulley take-up unit. The inside bolt was missing from the unit which allowed the top of the take-up unit to come loose, striking the employee on the left side of his face.

The employee was using a sledge hammer to know loose a used bucket tooth from it's chank. A small, sharp fragment flew off the edge of the tooth and impaled the employee in the right calf muscle.

While removing a rock from a conveyer belt with a shovel handle, the employee was struck on the left hand thumb with the other end of the shovel. The left thumb then struck the side of the conveyer.

The employee was cutting a piece of conveyor belting. While doing so, his right hand slipped causing the razor knife he was holding to strike his left thumb.

EMPLOYEE WAS CUTTING RIBBER BELT WITH A RAZOR KNIFE WHEN THE KNIFE SLIPPED AND STRUCK THE EE'SRIGHT KNEE.

EE WAS REPAIRING A BROKEN HYDRAULIC HOSE ON THE LOWER PORTION OF DREDGE CLAMSHELL BUCKET RAM. HE WRAPPED A CHAIN COME-ALONG AROUND THE SHAFT OF THE RAM TO MOVE THE RAM BACK FOR ACCESS TO THE HOSE FITTINGS. AFTER TENSION WAS APPLIED TO THE COME-ALONG, THE EE REACHED BEHIND THE RAM TO REMOVE THE BROKEN HOSE & THE HOSE FITTING. THE CHAIN ATTACHED TO THE RAM SLIPPED & ARM WAS CAUGHT.

The employee was tightening the conveyor belt on F1 conveyor. Employee hit is left hand fingers between a ratchet handle and conveyor frame.

EMPLOYEE, ALONG WITH TWO OTHERS, WERE CHANGING BUCKET TEETH AND SEGMENT ON EQUIPMENT. THE TEETH AND SEGMENTS FIT OVER ADAPTERS SECURED WITH PINS THAT ARE DRIVEN THROUGH ALIGNMENT HOLES IN THE WEAR PART AND THE ADAPTOR. ONE OF THE SECTIONS WOULD NOT LINE UP WITH THE PINHOLE SO THE EMPLOYEE TAPPED ON IT WITH A HAMMER. A METAL SPLINTER FROM THE SEGMENT FLEW UP AND HIT THE EMPLOYEE IN

EE WAS USING A BOTTLE JACK AND A PIECE OF PIPE TO RAISE THE ENGINE ON A LOADER. HE RAISED THE FRONT OF THE ENGINE AND INSTALLED A 1" PLATE TO MAKE ROOM TO REMOVE THE OIL PAN. THE EMPLOYEE LOWE RED THE JACK AND REMOVED THE JACK AND PIPE. THE PIPE SLIPPED OUT OF HIS HAND AND FELL ON HIS ARM CAUSING A LACERATION TO THE LEFT ARM.

EMPLOYEE WAS DIGGING DIRT AND GRAVEL FROM AROUND THE BASE OF OMNI #2 CONE CRUSHER. MUSCLE SPASMS IN THE BACK OF THE RIGHT SHOULDER CREATED PAIN FOR THE EMPLOYEE.

EE WAS USING A HAMMER TO ADJUST RETURN ROLLERS ON A BELT CONVEYOR. HE MISSED THE ROLLER AND STRUCK THUMB. INJURY REQUIRED SUTURES TO CLOSE.

WRENCH SLIPPED OFF BOLT, STRIKING EE ON CHIN

WHILE SPLICING F-1 CONVEYOR KNIFE SLIPPED AND STRUCK HIS LEFT THIGH.

PULLING ON STEEL PLATE WITH CHAIN HOIST. WELD BROKE LOOSE FROM LIFTING EYE ON STEEL PLATE. LIFTING EYE AND HOOK FROM CHAIN HOIST HIT EMPLOYEE IN FACE. FACIAL LACERATION REQUIRING SUTURE.

WHILE REPLACING BUCKET LINE ON DREDGE LADDER WITH TWO OTHER REPAIRMEN, A 1 1/2 BAR THAT IS USED TO PUSH OUT PINS, ROLLED OFF DREDGE LADDER, THE END OF BAR STRUCK THE TOP OF LEFT FOOT.

EMPLOYEE WAS HITTING CLAM SHEEL WITH A SLEDGE HAMMER MISSED CLAM SHELL AND HIT HIS OWN RIGHT MIDDLE FINGER WITH SLEDGE HAMMER.

EE WAS CUTTING RUBBER SKIRTING WHEN KNIFE CAME LOOSE AND CUT INISDE OF LEFT HAND.

EMPLOYEE WAS PREPARING TO DISLODGE ROCKS FROM THE CAVITY OF A KUE KEN JAW CRUSHER WITH A PRY BAR. WHILE ATTEMPTING TO DISLODGE THE ROCKS, A ROCK WEIGHING APPROX. 75 LBS SLID DOWN A SLIDE AT A 45 DEGREE ANGLE FOR APRPOX. 4.2 FEET MAKING CONTACT WITH EMPLOYEE'S LEFT HAND PINKY FINGER.

INJURED AND ANOTHER EMPLOYEE WERE INSTALLING A BOLT ON THE PORTABLE CRUSHER WHEN THE SOCKET WRENCH SLIPPED OUT OF EMPLOYEE'S HAND STRIKING HIS UPPER LIP.

EMPLOYEE WAS SECURING T-5 SCREEN ON 711 SHAKER Y HAMMERING WEDGE INTO PLACE. EMPLOYEE FAILED TO HIT THE HEAD OF THE WEDGE WITH #4 HAMMER AND LOST CONTROL OF HAMMER, WHICH CONTINUED DOWNWARD AN D HIT THE TOP OF HIS RIGHT FOOT.

EMPLOYEE WAS USING HACKSAW TO CUT PIPE - SAW SLIPPED OUT OF CUT GROOVE AND CUT LEFT INDEX FINGER.

EE WAS HITTING WEAR SHROUD ON THE BUCKET OF 858 LOADER TO REMOVE IT, WHEN A SMALL PIECE ABOUT THE SIZE OF A MATCH HEAD FLEW OFF AND STRUCK EE IN THE LEFT THIGH.

EE WAS INSTALLING SCREENS ON HEWIT ROBINS SCREEN WHILE TIGHTENING TENSION BOLTS HE MISSED AN HIT HIS LEFT HAND, INDEX FINGER WITH A 4 LB HAMMER.

EMPLYOEE WAS TRYING TO REMOVE A BEARING INSERT BY HITTING THE INSERT WITH A 3 LB HAMMER. A PIECE OF THE INSERT FLEW OFF AND LODGED ITSELF IN EMPLOYEE'S LEFT FOREARM.

WHILE USING SMALL SLEDGE HAMMER TO POUND ON A PLUGGED HOPPER,THE HANDLE HEAD BROKE CAUSING THE HEAD OF THE HAMMER TO FALL ON INJ HAND.

EMPLOYEE WAS HOLDING A WRENCH ON THE ANCHOR BOLT NUT,WHILE HIS PARTNER WAS TIGHTENING THE BOLT.EMPLOYEE LOST CONTROL OF THE WRENCH THE WRENCH FELL AND STRUCK HIM ON THE NOSE.

COME A LONG 3X3X5 CONCRETE BLCOK FROM GRAVITY TAKE UP BOX WHEN RED HEADERS THAT WERE DRILLE INTO BLOCK CAME OUT. EE ARM WAS FULLY EXTENDED AND UNDER STAIN WHEN COME A LONG CAME LOOSE, HURTING EE RIGHT SHOULDER. '

ATTEMPT TO TURN PULLEY WITH PRY BAR STRAINED R SHOULDER

MECHANIC WORK WAS BEING DONE ON AN OUT OF SERVICE TRUCK. HH WAS STANDING ON THE TRUCK AND WAS POUNDING IN A PIN TO THE HOIST RAM ON THE TRUCK BED. HH WAS 2 FT BEHIND OTHER EMPLOYEE, WHEN A SIL VER OF METAL FLEW OFF OF THE PIN AND STRUCK HIM IN THE THROAT. BOTH MECHANICS WERE WEARING SAFETY GLASSES AND STEEL TOED BOOTS. ALL SAFETY & WORK RULES WERE COMPLIED TO. BOTH MECHANICS DISPLA

INJURED WAS CUTTING A CONVEYOT BELT WHEN HIS KNIFE SLIPPED AND CUT HIS LEG.

EMPL WAS SHOVELING DIRT IN TIGHT AREA & HIT METAL PLATE BEHIND HIM. BOLT WAS STICKING OUT OF PLATE.

PULLING COMEALONG ,CHAIN BROKE HITTING LEFT SHOULDER.

WORKING ON CRUSHER.REOCCURENCE OF PRIOR INJURY TO RIGHT KNEE-5-9-87. NOTIFY OF PROBLEM TO RIGHT KNEE AGAIN 2-9-90.

ADJUSTING JAW CRUSHER USING BOTTLE JACK JACK FELL HITTING THE R BIG TOE

EMPL WAS SHARPENING KNIFE WITH A FILE WHILE HE WAS HOLDING THE KNIFE AGAINST HIS LEG THE FILE HOOKED BLADE AND FLIPPED KNIFE OVER CUTTING HIS LEG

WHILE SWINGING A SLEGE HAMMER TRYING TO LOOSEN NUTS ON CRUSHER. HE TWISTED AND INJURED HIS BACK.