Buscar en el registro

Employee was flipping cutting edges on a D-11 bulldozer. The employee was using a 24-inch pry bar to rotate the cutting edge. When the cutting edge unexpectedly shifted employee got right pinky finger pinched between the pry bar and the shop floor. Employee was wearing leather gloves.

Employee was replacing the wheel studs on 605 fuel/lube truck, using a punch and hammer. Employee was holding the punch with gloved right hand when the hammer glanced off the punch striking EE's thumb.

EE was replacing the idler arms on a D10 dozer. EE was using a RAD torquing wrench on inside bolt. The reaction arm was pointing upward. EE placed right hand on reaction arm & left hand on the trigger of the wrench. When EE applied torque pressure to the wrench, the reaction arm rotated causing right hand to be caught/pinched between the idler & the reaction arm.

Using a pry bar to remove Becket from Dump Rope Socket. Pry bar slipped, smashing employee's thumb between pry bar and dump rope sheave. An x-ray showed a fracture of the tip of employees left thumb. The employee was wearing gloves at the time of this incident.

While assembling a retainer on 104 dragline on left propel case. Employee was using a pry bar to adjust alignment of retainer. The bar was too long to get in a comfortable position and was being used overhead. The bar slipped smashing right thumb between bar and bull gear cover.

Employee was using a 36" pipe wrench to open a valve. The valve opened suddenly, employee pinched finger between the wrench and circulating pump fracturing finger.

During a wire rope resocket the employee got his left hand pinched between a pry bar and the wire rope. Stitches were required on the little finger of the left hand.

Working on the camshaft of a C27. While removing the bolts the socket wrench slipped and caused left hand to smash up against the camshaft. The drive gear cut left finger at base.

When adjusting an irrigation pipe, a tye wrap needed to be cut to move the piping. A pocket knife was used, in the process the knife slipped cutting the person's left thumb requiring stitches.

EE was working on equipment using a hammer to remove pin and piece of metal came off pin and embeded in left forearm.

Employee was cutting discharge hose with a utility knife. Discharge hose was propped up on his leg. During process of cutting hose, the knife slipped out of the hose and cut his leg.

Mechanic was putting new bushings on a dozer cylinder. When the bushing became stuck he hit it with a hammer, which flaked off striking him in the arm. In removing the sliver of metal, the doctor required a stitch to close the entry point. Mechanic was wearing leather gloves and a face shield at time of incident.

While lowering the axle on a Dart CH-160 trailer, the axle began to roll off of the jacks and extentions, When the axle began to fall, it hit the torsion bar and the bar hit employee in the left shoulder, knocking him away from the falling axle.

While working on a Dart CH-160 Trailer, ee was lowering the axle on jacks and extentions and the axle began to roll off of the jacks and landed on ee's left foot and crushed it.

EE WAS REMOVING A BUSHING FROM A TRACKHOE BUCKET WHEN STRUCK IN LEFT ARM BY A FRAGMENT OF METAL. THE PIECE OF METAL WAS REMOVED AND STITCHES APPLIED TO CLOSE THE IMPACT AREA.

EMPLOYEE WAS REMOVING OIL FILTER. FILTER WRENCH WOULD NOT LOOSEN FILTER, SO HE DROVE A SCREWDRIVER THROUGH THE FILTER, BREAKING THE FILTER. WHILE REMOVING THE FILTER IT SLIPPED AND CUT HIS HAN D.

EE WAS REMOVING AN OLD TOOTH FROM THE EASI MINER CUTTING HEAD WITH A HAMMER. A PIECE OF THE TOOTH BROKE OFF AND STRUCK THE EE IN THE RIGHT THIGH. A PHYSICIAN REMOVED THE SLIVER OF METAL AND US ED STITCHES TO CLOSE THE WOUND.

EMPLOYEE WAS PULLING ON A WRENCH WHEN HE FELT SOMETHING POP IN HIS RIGHT SHOULDER.

EE WAS INSTALLING A BEARING IN THE SOUTH ARM BUSHING OF #202 EASI-MINER WITH A 21LB SLEDGE HAMMER. A SPLITNER OF METAL HIT LEFT THUMB REQUIRING STITCHES.

EE WAS UNLOADING A 10-1/2' X 2" WIRE SLING. HE CUT THE BANDING THAT HOLDS THE SLING IN A LOOP. THE SLING RECOILED & STRUCK HIS LEFT THUMB CAUSING A LACERATION.

MAINTENANCE TECH RECEIVED A LACERATION TO THE LEFT HAND WHILE SHARPENING A GASKET SCRAPER WITH AFILE.

EE MECHANIC WAS REMOVING A A/C FALL COVER WITH RAZOR UTILITY KNIFE AT ONE POINT THE KNIFE SLIPPED & THE BLADE STRUCK HE FELT INDEX FINGER LACERATING THE END WHERE 5 STITCHES WERE REQUIRED TO REPAIR REPAIR

WELDER WAS CHIPPING ON WELD IN THE BASE OF DRAGLINE WHEN SMALL PARTICLE WENT IN RT EYE PARTICLE WASNT EMBEDDED ONLY STUCK ON LID WELDER WAS WEARING SAFETY GLASSES

MECHANIC WAS CHANGING TEETH ON A 1224 EASIMINER.HE WAS STRIKING THE TOOTH WITH A SLEDGE HAMMER. AT THE END OF THE SHIFT, HE FELT PAIN IN HIS LEFT SHOULDER. HE VISITED THE CHIROPRACTOR ON 9-8-94. THE CHIROPRACTOR KEPT HIM OFF WORK UNDERHIS CARE UNTIL FURTHER NOTICE, WITH TREATMENT ONGOING DAILY.

EMPLOYEE WAS MOVING PIPE INTO BASE OF DRAGLINE FOR WELDER. THE BAR HE WAS USING TO MOVE THE PIPE SLIPPED, CAUSING A PLATE TO MOVE, SMASHING A FINGER ON EACH HAND. LEFT MIDDLE FINGER (DISTAL DI GIT) HAD 2 CM LACERATION AND FRACTURE. RIGHT RING FINGER (DISTAL DIGIT) WAS FRACTURED AS WELL.

EMPLOYEE WAS USING A 20 LB SLEDGE HAMMER TO REMOVE SHOVEL TEETH. DURING THE OPERATION HE STRAINED HIS BACK. ON 8-23-94 HE WENT TO THE CHIROPRACTOR AND REQUIRED TIME OFF RELATED TO THIS INJURY.

DRAGLINE CREW WAS IN THE PROCESS OF REPLACING BUCKET TEETH ANDWEARPLATES ON DRAGLINE 102 A 1570 BE DRAGLINE. THE OEPRATOR WAS IN THE PROCESS OF KNOCKING OFF HTE WEARPLATES WITH A 20 LB SLEDGE HAMMER. THE OPERATOR HIT THE WEARPLATE WITH THE HAMMER AND A SLIVER O FMETAL FLEW OFF THE WEAR PLATE AND STRUCK THE OILER IN THERIGHT FOREARM. THE OILER WAS TAKEN TO THE E.R. ROOM WHERE 7 S

WELDER WAS SWINGING A HAMMER AND REPORTED TWISTING HIS BACK.

CO-WORKER WAS DRIVING DOWEL PIN ON PROPEL CAM BUSING OF BUCYRUS ERIE WALKING DRAGLINE WITH A SLEDGE HAMMER. THE HAMMER GLANCED OFF THE DOWELL STRIKING A 2 FOOT BAR WHICH FLEW OUT OF THE HOLE, STRIKING INJURED EMPLOYEE ON THE NOSE.

EE WAS USING PRY BAR OUT OF POSITION FELT A POP IN CHEST WHILE APPLYING FORCE TO PRY BAR.

55061S OPENING ROD CAN HIS HAND SLIPPED AGAINST EDGE OF CAN LACERATING 5 TH FINGER APPROX. 1 1/2 INCH LONG REQUIRING 3 STITCHES.

39783ENING BOLTS ON BORING EQUIPMENT. WRENCH SLIPPED ELBOW STRUCK ANGLE IRON.

EMPLOYEE WERE REPLACING DRAGROPE IN SOCKE TWHEN, IN THE PROCESS, THE DRAG ROPE HUNG UP. AS INJURED PARTY PUSHED ON THE ROPE WITH A PRY BAR, THE 5/16" STEEL CHOKER BROKE, ALLOWING THE DRAG ROP E TO SPRINGFREE, STRIKING EMPLOYEE'S RIGHT LEG.

EMPLOYEE WAS TIGHTENING BOLTS ON AN EASI-MINER OIL COOLER PUMP WHEN IT SLIPPED OUT OF THE VISE IN WHICH IT HAD BEEN SECURED.THE EMPLOYEE STEPPED BACK;HOWEVER,THE PUMP STRUCK HIM ON THE LEFT FO OT.EMPLOYEE HAD A NON-DISPLACED FRACTURE OF THE FIFTH METATARSAL.

EMPLOYEE WAS PULLING WINCH CABLE FROM CATERPILLAR DOZER WINCH WHEN HE MASHED HIS RIGHT INDEX AND MIDDLE FINGERS.

EE WAS JACKING UP HIS PICK UP TRUCK AFTER HAVING THE RIGHT REAR TIRE BLOW OUT HIS RIGHT HAND SLIPPED OFF THE HANDLE OF THE JACK AND SLIPPED AND HIT BASE OF JACK CAUSING A FRACTURE OF HIS RIGHT RING FINGER.

INJURED WAS ATTEMPTING TO CUT THE LUGS FROM THE SHORT CONVEYOR BELT ON THE HURON EASI-MINER (WHERE THE FASTENER'S HOLD THE BELT TOGETHER). INJURED WAS HOLDING THE BELT UP WITH HIS LEFT HAND AN D CUTTING WITH HIS RIGHT. THE KNIFE CUT THROUGH EASIER AND FASTER THAN ANTICIPATED CUTTING 2 FINGERS ON THE LEFT HAND.

EMPLOYEE WAS REMOVING CUTTING TEETH FROM EASI-MINER WHEN THE SOCKET HE WAS USING SLIPPED & STRUCK HIS LEFT INDEX FINGER

EMPL WAS ASSISTING WITH CHANGING TEETHON DRAGLINE BUCKET WHEN HE STRUCK WEAR PLATE WITH 8 LB SLEDGE HAMMER TO LOOSEN PLATE. WHEN HAMMER CONTACTED WEAR PLATE PIECE OF STEEL BROKE LOOSE STRIKING EMPL IN FINGER.

INJURED WAS CUTTING PAPER WITH A PAPER CUTTER. IN THE CUTTING PROCESSS INJURED THUMNB WAS IN THE WAY RESULTING IN THE THUMBNAIL BEING RIPPED OFF.

INJURED WAS USING A 20 LB HAMMER AND A PIN HAMMER WHILE REPAIRING A COLD ROLL PIN ON DUMP ROPE SOCKET OF A BUCYRUS ERIE 1570 DRAGLINE DUMP ROPE DURING THE PROCEDURE THE SLEDGE HEAD SLIPPED OFF THE HEAD OF THE PIN HAMMER CATCHING LEFT THUMB BETWEEN THE SLEDGE HAMMER HANDLE AND THE DUMP ROPE SOCKET

INJURED WAS INSTALLING A NEW TRACK ON A CATERPILLAR D-9L INSO DOING A 308 IN CHAIN WAS BEING USED TO PULL THE TRACK OVER THE FINAL DRIVE OF THE MACHINE THE CHAIN WAS TO SHORT SO ANOTHER CHA IN WAS CONNECTED LEAVING THE HOOK OF THE FIRST CHAIN DRAGGING THE CHAIN SLIPPED WHICH CAUSED THE DRAGGING HOOK TO GO THROUGH THE INJURED HAND AND CUT OPEN HIS HAND

WHILE CLEARING 4ILLOW TREES WITH A MACHETE THE INJURED CUT HIS ARM WHEN SWINGING THE MACHETE

INJURED WAS DRI5ING A BOLT OUT WITH A FOUR POUND HAMMER WHILE SWINGING THE HAMMER HE HIT THE FINGER NAIL DEFECTING THE HAMMER CAUSING HIM TO SMASH HIS FINGER

INJURED WAS TRI4MING LIMBS OFF OF A DEAD AND TREE WITH A MACHETTE. THE MACHETTE GLANCE OFF AND STRUCK RIGHT KNEE CAUSING A LACERATION.

KNEELING ON KNE9S APPLYING DOWNWARD PRESSURE ON BREAK-OVER WRENCH, NUT BROKE LOOSE AND PALM OF R HAND CONTACT SHOP FLOOR

GROUNDMAN WAS STANDING ON LIP OF DRAGLINE BUCKET WHILE CHANGING BUCKET TEETH. GROUNDMAN WAS USING A SLEDGE HAMMER TO DRIVE TOOTH RETAINING PINS BACK INTO POSITION. AS GROUNDMAN WAS SWINGING HA MMER, IT GLANCED OFF OF PIN AND STRUCK INJURED IN THE MOUTH.

WHILE OBSERVING GROUNDMAN DRIVE A PIN INTO A NEW DRAGLINE BUCKET TOOTH, A SLIVER OF STEEL BROKE FROM THE PIN WHEN STRUCK BY THE HAMMER, HITTING THE EMPLOYEE IN THE RIGHT ARM AND IMBEDDING ITSE LF UNDER THE SKIN.

EMPLOYEE WAS USING PIPE WRENCH AND WORKING IN SMALL CONFINED AREA. HE PULLED ON THE WRENCH AND IT SLIPPED AND HIT HIM IN THE MOUTH.

EMP WAS WORKING OUT OF BUCKET ON THE PICKER LIFTING PIN FOR CABLE. PIN WAS TIED WITH COME ALONG AND CHAIN. CHAIN CAME LOOSE AND PIN DROPPED ABOUT 1 FOOT AND HE CAUGHT IT, PULLING HIS BACK